2013 JEEP GRAND CHEROKEE radio

WARNING!(Continued)
could detect the ball mount and hitch ball assem-
bly, depending on its size and shape, giving a false
indication that an obstacle is behind the vehicle.
PARKVIEW® REAR BACK UP CAMERA — IF
EQUIPPED
Your vehicle may be equipped with the ParkView® Rear
Back Up Camera that allows you to see an on-screen
image of the rear surroundings of your vehicle whenever
the shift lever is put into REVERSE. The image will be
displayed on the Navigation/Multimedia radio display
screen along with a caution note to “check entire sur-
roundings” across the top of the screen. After five sec-
onds this note will disappear. The ParkView® camera is
located on the rear of the vehicle above the rear License
plate.When the vehicle is shifted out of REVERSE, the rear
camera mode is exited and the navigation or audio screen
appears again.
When displayed, static grid lines will illustrate the width
of the vehicle while a dashed center-line will indicate the
center of the vehicle to assist with aligning to a hitch/
receiver. The static grid lines will show separate zones
that will help indicate the distance to the rear of the
vehicle. The following table shows the approximate
distances for each zone:
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255

NOTE:If snow, ice, mud, or any foreign substance
builds up on the camera lens, clean the lens, rinse with
water, and dry with a soft cloth. Do not cover the lens.
Turning ParkView® On Or Off — With
Navigation/Multimedia Radio
1. Press the “menu” hard-key.
2. Select “system setup” soft-key.
3. Press the “camera setup” soft-key.
4. Enable or disable the rear camera feature by selecting
the “enable rear camera in reverse” soft-key.
5. Press the “save” soft-key.
Turning ParkView® On Or Off — Without
Navigation/Multimedia Radio
1. Press the “menu” hard-key.
2. Select “system setup” soft-key.
3. Enable or disable the rear camera feature by selecting
“enable rear camera in reverse” soft-key.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257

Before You Begin Programming HomeLink®
Be sure that your vehicle is parked outside of the garage
before you begin programming.
For more efficient programming and accurate transmis-
sion of the radio-frequency signal it is recommended that
a new battery be placed in the hand-held transmitter of
the device that is being programmed to the HomeLink®
system.
Erase all channels before you begin programming. To
erase the channels place the ignition in the ON/RUN
position and press and hold the two outside HomeLink®
buttons (I and III) for up 20 seconds or until the red
indicator flashes.NOTE:
•Erasing all channels should only be performed when
programming HomeLink® for the first time. Do not
erase channels when programming additional buttons.
•If you have any problems, or require assistance, please
call toll-free 1–800–355–3515 or, on the Internet at
www.HomeLink.com for information or assistance.
Programming A Rolling Code
For programming garage door openers that were manu-
factured after 1995. These garage door openers can be
identified by the “LEARN” or “TRAIN” button located
where the hanging antenna is attached to the garage door
opener. It is NOT the button that is normally used to
open and close the door. The name and color of the
button may vary by manufacturer.
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Canadian/Gate Operator Programming
For programming transmitters in Canada/United States
that require the transmitter signals to “time-out” after
several seconds of transmission.
Canadian radio frequency laws require transmitter sig-
nals to time-out (or quit) after several seconds of trans-
mission – which may not be long enough for HomeLink®
to pick up the signal during programming. Similar to this
Canadian law, some U.S. gate operators are designed to
time-out in the same manner.
It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage
door or gate motor.
1. Cycle the ignition to the ON/RUN position.
2.
Place the hand-held transmitter 1 to 3 in (3 to 8 cm)
away from the HomeLink® button you wish to program
while keeping the HomeLink® indicator light in view.
3. Continue to press and hold the HomeLink® button,
while you press and release (“cycle”), your hand-held
transmitter every two seconds until HomeLink® has
successfully accepted the frequency signal. The indi-
cator light will flash slowly and then rapidly when
fully trained.
4. Watch for the HomeLink® indicator to change flash
rates. When it changes, it is programmed. It may take
up to 30 seconds or longer in rare cases. The garage
door may open and close while you are programming.
5. Press and hold the programmed HomeLink® button
and observe the indicator light.
•If the indicator light stays on constantly, program-
ming is complete and the garage door/device should
activate when the HomeLink® button is pressed.
•To program the two remaining HomeLink® buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

ROOF LUGGAGE RACK — IF EQUIPPED
The crossbars and siderails are designed to carry the
weight on vehicles equipped with a luggage rack. The
load must not exceed 150 lbs (68 kg), and should be
uniformly distributed over the luggage rack crossbars.
NOTE:If not equipped with crossbars, your authorized
dealer can order and install MOPAR® crossbars built
specifically for this roof rack system.
Distribute cargo weight evenly on the roof rack crossbars.
The roof rack does not increase the total load carrying
capacity of the vehicle. Be sure the total load of cargo
inside the vehicle plus that on the external rack does not
exceed the maximum vehicle load capacity.
To move the crossbars, loosen the attachments, located at
the upper edge of each crossbar, approximately eight
turns using the anti-theft wrench provided with the
MOPAR® crossbars. Then, move the crossbar to thedesired position, keeping the crossbars parallel to the
rack frame. Once the crossbar is in the desired position,
retighten the with the wrench to lock the crossbar into
position.
NOTE:
•To help control wind noise when the crossbars are not
in use, place the front and rear crossbars approxi-
mately 24 in (61 cm) apart. Optimal noise reduction
can then be achieved by adjusting the front crossbar
forward or aft using increments of 1 in (2.5 cm).
•If the rear crossbar (or any metallic object) is placed
over the satellite radio antenna (if equipped), you may
experience interruption of satellite radio reception. For
improved satellite radio reception, avoid placing the
rear crossbar over the satellite radio antenna.
•The grab handles on the back of the vehicle (if
equipped) are not to be used as a towing feature.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 295

▫Keyless Enter-N-Go™ Display —
If Equipped.........................335
▫Compass / Temperature Display..........336
▫Customer-Programmable Features
(System Setup).......................338
Uconnect® 730N/430/430N CD/DVD/HDD/
NAV — If Equipped....................347
▫Operating Instructions (Voice Command
System) — If Equipped.................347
▫Operating Instructions (Uconnect® Phone) — If
Equipped...........................347
Uconnect® 130.........................347
▫Operating Instructions — Radio Mode.......348
▫Operation Instructions — CD MODE For
CD And MP3 Audio Play................351▫Notes on Playing MP3 Files..............353
▫Operation Instructions - Auxiliary Mode.....356
Uconnect® 130 WITH SATELLITE RADIO.....356
▫Operating Instructions — Radio Mode.......356
▫Operation Instructions — CD MODE for
CD and MP3 Audio Play................362
▫Notes On Playing MP3 Files..............364
▫LIST Button (CD Mode for MP3 Play).......367
▫INFO Button (CD Mode for MP3 Play)......367
▫Operating Instructions (Uconnect®
Phone) — If Equipped..................368
▫Uconnect® Multimedia (Satellite
Radio) — If Equipped..................368
298 UNDERSTANDING YOUR INSTRUMENT PANEL

iPod®/USB/MP3 CONTROL —
IF EQUIPPED.........................373
▫Connecting The iPod® Or External USB
Device.............................373
▫Using This Feature.....................374
▫Controlling The iPod® Or External USB Device
Using Radio Buttons...................375
▫Play Mode..........................375
▫List Or Browse Mode...................376
▫Bluetooth Streaming Audio (BTSA).........378
UCONNECT® MULTIMEDIA — VIDEO
ENTERTAINMENT SYSTEM (VES)™ — If
Equipped.............................380
▫Getting Started.......................380
▫Single Video Screen....................380▫Play Video Games.....................384
▫Listen To An Audio Source On Channel 2 While A
Video Is Playing On Channel 1............386
▫Important Notes For Single Video Screen
System.............................388
▫Play A DVD Using The Touch-Screen Radio . . .389
▫VES Remote Control – If Equipped.........391
▫Remote Control Storage.................393
▫Locking The Remote Control.............394
▫Replacing The Remote Control Batteries......394
▫Headphones Operation.................395
▫Controls............................396
▫Replacing The Headphone Batteries.........397
4
UNDERSTANDING YOUR INSTRUMENT PANEL 299

▫Unwired® Stereo Headphone Lifetime Limited
Warranty...........................397
▫System Information....................398
STEERING WHEEL AUDIO CONTROLS — IF
EQUIPPED...........................415
▫Radio Operation......................416
▫CD Player...........................416
CD/DVD DISC MAINTENANCE...........417RADIO OPERATION AND MOBILE PHONES . .417
CLIMATE CONTROLS...................418
▫Dual-Zone Manual Heating And
Air Conditioning.....................418
▫Dual-Zone Automatic Temperature
Control (ATC) — If Equipped............422
▫Operating Tips.......................429
300 UNDERSTANDING YOUR INSTRUMENT PANEL