2013 INFINITI FX Quick Reference Guide

INFINITI Intelligent Key™ System
The INFINITI Intelligent Key™ system allows you to lock or
unlock your vehicle, open your liftgate and start the engine.
NOTE: It is important to make sure the Intelligent Key is
with you (that is, in your pocket or purse).

The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.

To lock the vehicle, push either door handle request
switch

01 once or press the
button
02 on the keyfob.

To unlock the vehicle, perform one of the following procedures:
• Push either door handle request switch

01 once;

the corresponding door will unlock. Push the door
handle request switch

01 again within 1 minute;

all other doors will unlock, or
• Press the

button
03 on the keyfob to unlock the
driver’s side door. Press the

button again; all
other
doors will unlock.

To open the liftgate, press the button
04 for more than 1 second.

The Intelligent Key can also be used to activate the panic alarm by pressing and holding the

button
05 for more than 1 second. Once activated, the panic alarm and headlights will stay
on for 25 seconds.
INFINITI INTELLIGENT KEY
™ BATTERY DISCHARGE

If the battery in the Intelligent Key is almost discharged,
the guide light

06 of the Intelligent Key port blinks and
the Intelligent Key insertion indicator
07 is displayed
in the vehicle information display.

To start the engine under these circumstances, insert
the Intelligent Key into the key port with the keyring
side facing backward until it latches into place. Then
push the ignition switch to start the engine.

To remove the Intelligent Key from the port, push the
ignition switch to turn the engine off and then pull the
Intelligent Key out of the port.

The Intelligent Key port does not charge the Intelligent
Key battery. If you see the Intelligent Key warning light

08 , replace the battery in the Intelligent Key.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)”, “Starting and driving (section 5)” and the “Maintenance
and do-it yourself (section 8)” of your Owner’s Manual.
first drive features
01
02
03
04
05
06
F
E
07
08
7

8
first drive features
Power Liftgate
When the liftgate is closed, the liftgate will open
automatically by:

Pushing the power liftgate switch
01 on the
instrument panel.

Pushing the liftgate opener switch
02 .

Pressing the button
03 on the INFINITI
Intelligent Key™ for more than 1 second.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
Power Seat Adjustments

To slide the seat forward or backward, push the control
switch

01 forward or backward .


To recline the seatback, push the switch
02

forward or backward.
SEAT LIFTER

To raise or lower the front portion or height of the seat,
push the front or back end of the switch

01
up or down.

POWER LUMBAR SUPPORT

To adjust the seat lumbar support, push the front or back end of the switch
03 .
For more information, refer to the “Safety —— seats, seat belts and supplemental restraint system (section 1)” of your

Owner’s Manual.
01
02
03
010203

9
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner memory.

Follow these procedures to set the memory positions:
• Confirm the shift lever is in the P (PARK) position.
• Push the ignition switch to the ON position.
• Adjust the driver’s seat, steering column and outside mirrors to the desired positions
using the adjusting switches for each feature.
• Push the SET switch and within 5 seconds, push the memory switch (1 or 2) for at least 1 second.
• The indicator light on the memory switch you select will illuminate for approximately 5 seconds.
• The driver’s seat, steering column and outside mirror positions are now set to your preference.

These memorized positions can also be linked to your INFINITI Intelligent Key™.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Outside Mirror Control Switch
To select the right or left side mirror, move the control
switch

01 right or left.


To adjust each mirror to the desired position, use the
control switch

02 .

To fold the outside rearview mirrors, push the switch

03 to the CLOSE
position and to unfold the outside
rearview mirrors push the switch
03 t
o the OPEN
position.
REvERSE TILT-DOWN FEATURE (if so equipped)

When backing up the vehicle, the right or left outside mirror can be selected to turn downward to
provide better rear visibility.
1. Push the ignition switch to the ON position.
2. Move the shift lever to the R (REVERSE) position.
3. Choose the right or left outside mirror by operating the outside mirror control switch

01 .
4. The selected outside mirror surface moves downward.
NOTE: The control switch
01 must be in the right or left position for the reverse tilt-down feature
to function.

When one of the following conditions has occurred, the outside mirror surface will return to its
original position:

• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch is set to the center “neutral” position.
• The ignition switch is pushed to the Off position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
01
02
03

10
first drive features
Starting/Stopping the Engine
NOTE: It is important to make sure the INFINITI Intelligent
Key™ is with you (that is, in your pocket or purse).

Depress the brake pedal.
• If the brake pedal is not depressed, pushing the
ignition switch once enters the ACC mode.
• If the ignition switch is pushed a second time, the
vehicle will enter the ON mode.

Move the shift lever to P (PARK).

Push the ignition switch to start the engine.
TURNING THE ENGINE OFF

Move the shift lever to the P (PARK) position and apply the parking brake.

Press the ignition switch START/STOP button to turn the engine off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Headlight Control Switch
Turn the headlight control switch to the position

01 to turn on the front parking, side marker, tail,

license plate and instrument panel lights. Turn the
switch to the

position
02 to turn on the

headlights.
AUTOLIGHT SYSTEM

The autolight system will automatically turn the headlights on when it is dark and off when it is
light. The system will keep the headlights on for a period of time after you turn the ignition off
and all doors are closed.

To activate the autolight system, turn the headlight control switch to the AUTO position
03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight

control switch to the Off,

01 or
position
02 .

HIGH BEAM SELECT

Push the headlight control switch forward
04 to
select the high beam function. The blue indicator
light
illuminates in the instrument panel. Pull
the headlight switch back to the original position to
select the low beam. The blue indicator light goes off.

Pull and release the headlight control switch
05 to
flash the headlight high beams on and off.
03
04
05
01
02

11
Windshield Wiper/Washer Switch
Move the lever to the following positions to operate
the windshield wipers:

01 Mist (MIST) - One sweep operation of the
front wipers.

02 Intermittent (INT) - Operates the speed-sensing
and rain-sensing (if so equipped) front wipers
intermittently. The intermittent operation speed
can be adjusted by twisting the time control
ring
03 .

04 Low (LO) - Front wipers operate at a continuous
low-speed.

05 High (hI) - Front wipers operate at a continuous
high-speed.

06 Front washer - Pull the lever toward you

to activate the front washer. The front wipers
will operate several times.
REAR WINDSHIELD WIPER AND WASHER

07 Intermittent (INT) - Rear wiper operates
intermittently.

08 Low (ON) - Rear wiper operates at a continuous
low-speed.

09 Rear washer - Push the lever forward to
activate the rear washer. The rear wiper will
operate several times.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
06
FOG LIGHT SWITCH
NOTE: The headlights must be on and the low beams
selected for the fog lights to operate.

Turn the switch (inside collar) to the position
06
to turn the fog lights on.

Turn the switch (inside collar)
to the Off position to
turn the fog lights off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
INT
ON
MIST Off
INT
LO
hI01
02
04
05
03
06
09
07
08

2013 Infiniti FX Delivery Checklist
Bluetooth® Hands-free Phone System
Ye s
1. Connect the customer’s phone


2. Explain voice tagging


3. Identify microphone location


4. Explain how to dial a number


5. Explain how to receive and end a call


Navigation System (if so equipped)
Demonstrate Ye s
1. How to operate the touch screen


and/or scrolling dial
2. How to add a home location


3. How to set a destination


4. How to search for nearby places


5. How to turn the display off

Outside Mirrors
Demonstrate Ye s
1. Outside mirror adjustment switch location

2. Right and left mirror adjustment

3. Neutral switch position


4. Mirror tilt down function (if so equipped)

Audio System
Demonstrate Ye s
1. How to tune in to the next broadcast station and


skip to the next category (if so equipped) or CD track
2. How to store a radio station in a preset


3. How to scan the broadcast stations

Seat Adjustments
Demonstrate Ye s
1. How to slide the front seat forward or backward


2. How to recline the front seat


3. How to operate the seat lifter


4. How to operate the lumbar support


5. How to operate the heated/cooled


seat controls (if so equipped)
6. How to fold the rear seats

Bluetooth®Controls

2013 Infiniti FX Delivery Checklist
Windshield Wiper/Washer Switch
Demonstrate Ye s
FRONT WINDSHIELD WIPER AND WASHER
01 MIST (one sweep) function

02 Intermittent (INT) wiper function

03 Time delay adjustment ring

04 Low (LO) speed wiper function

05 High (hI) speed wiper function

06 Front washer
function



REAR WINDSHIELD WIPER AND WASHER
07 Intermittent (INT) wiper function

08 ON wiper function

10 Rear washer function



RAIN-SENSING AUTO WIPER SYSTEM
(if so equipped)
09 Rain-Sensing Auto Wiper System operation

INT
ON
MIST Off
INT
LO
hI01
02
04
05
03
06
09
07
08
Heating, Ventilation and Air Conditioning
Demonstrate Ye s
1. AUTO mode and DUAL mode


2. Fan Speed control

3. Mode control


4. A/C function

5. Defrost and Defog operation
(include recirculation button)
All information, specifications, photographs and illustrations are those in effect at the time of printing. INFINITI
reserves the right to change specifications or design without notice and without obligation. For additional
information, see your INFINITI retailer or contact NISSAN North America, Inc. See your Owner’s Manual for
important warnings and details on vehicle operation and maintenance.
QR3E 0S51U0
Printing: June 2012 (10)
Printed in USA
Owner’s Signature Date

Sales Consultant’s Signature Date

Sales Manager’s Signature Date

12
first drive features
Automatic Climate Control (if so equipped)
01 AUTO BUTTON/DRIVER’S SIDE TEMPERATURE CONTROL DIAL


The auto mode may be used year-round. Press the AUTO button to turn the system on
and the system will automatically control the inside temperature (automatic cooling and/
or dehumidified heating), air flow distribution and fan speed.

Turn the driver’s side temperature control dial to the left for cooler air or right for warmer air.
02 DUAL BUTTON/PASSENGER’S SIDE TEMPERATURE CONTROL DIAL

Press the DUAL button to turn the passenger’s side temperature controls on or off. This
will allow the passenger’s side temperature to be adjusted independently from the driver’s
side by turning the passenger’s side temperature control dial.

Turn the passenger’s side temperature control dial left for cooler air or right for warmer air.
03 f
AN SPEED CONTROL BUTTONS

To manually adjust the fan speed, press the top button to increase the fan speed or
press the bottom button to decrease the fan speed.
04 DEfROSTING/DEfOGGING fRONT AND SIDE WINDOWS

Press the defroster control button
to turn the system on. The A/C automatically turns

on when the defroster mode is selected. This feature removes humidity from the air.

Turn the temperature control dial
01 to set the desired temperature.

To defrost the front and side windows quickly, set the temperature controls and fan speed
controls to their maximum settings.
05 MODE BUTTON


Press the MODE button
to cycle through the following air flow outlets:

Air flows from the center and side vents.

Air flows from the center, side and foot vents.

Air flows mainly from the foot vents.

Air flows from the defroster and foot vents.
06 DEfROSTING REAR WINDOW AND OUTSIDE MIRRORS

Push the rear window defroster switch to turn the system on or off.

This function automatically turns off after approximately 15 minutes.
010302
09
08
06
04
07
05