2013 INFINITI EX ignition

*See your Owner’s Manual for information.
01
INSTRUMENT BRIGHTNESS
cONTROL SwITcH*
02
TRIP cOMPUTER S wITcHES
03
LO w TIRE PRESSURE wARNING LIGHT
04
HEADLIGHT AND TURN SIGNAL cONTROL
05 wINDSHIELD wIPER / w
ASHER SwITcH
06
STEERING wHEEL SwITcHE S FOR
AUDIO* / BLUETOOTH® / NAVIGATION
07
INTELLIGENT cRUISE c ONTROL BUTTONS
08
PUSH BUTTON IGNITION
09 w
ARNING SYSTEMS S wITcH*
10
INTELLIGENT BRAKE ASSIST (IBA)
OFF S wITcH*
11
DYNAMIc DRIVER ASSISTANc E SwIT cH*
12
INTELLIGENT KEY PORT
13
TILT / TELESc OPIc STEERING
wHEEL S wITcH*
14
HOOD RELEASE*
15
VEHIcLE DYNAMIc cONTROL (VDc)
OFF S wITcH*
16 c
ONTROL PANEL DISPLAY ScREEN*
17
AUDIO SYSTEM
18
AUTOMATIc cLIMATE cONTROLS
19
FRONT PASSENGER AIR BAG STATUS LIGHT*
01
Behind
steering wheel Behind
steering wheel
On
steering column
0405
08
0910
16
17
18
19
11
1213
14
02
03
0706
15Behind
steering wheel

4
first drive features
INFINITI Intelligent Key™ System
The INFINITI Intelligent Key™ System allows you to lock or
unlock your vehicle, open your liftgate and start the engine.
NOTE: It is important to make sure the Intelligent Key is
with you (that is, in your pocket or purse).

The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.

To lock the vehicle, push either door handle request
switch

01 or the liftgate request switch
02 or press
the

button
03 on the keyfob.

To unlock the vehicle, perform one of the following
procedures:
• Push either door handle request switch

01 or the
liftgate request switch
02 ; the corresponding door will unlock.
Push the door handle request switch
01 or the liftgate request
switch
02 again within 1 minute; all other doors will unlock, or
• Press the

button
04 on the keyfob to unlock the driver’s side

door. Press the

button again; all other doors will unlock.

The Intelligent Key can also be used to activate the panic alarm by
pressing and holding the

button
05 for more than 1 second. Once

activated, the panic alarm and headlights will stay on for 25 seconds.
INFINITI INTELLIGENT KEY
™ BATTERY DIScHARGE

If the battery in the Intelligent Key is almost discharged,
the guide light

06 of the Intelligent Key port blinks and
the Intelligent Key insertion indicator
07 is displayed
in the dot matrix liquid crystal display.

To start the engine under these circumstances, insert
the Intelligent Key into the key port with the keyring
side facing backward until it latches into place. Then
push the ignition switch to start the engine.

To remove the Intelligent Key from the port, push the
ignition switch to turn the engine off and then pull the
Intelligent Key out of the port.

The Intelligent Key port does not charge the Intelligent
Key battery. If you see the Intelligent Key warning light

08 , replace the battery in the Intelligent Key.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)”, “Starting and driving (section 5)” and the “Maintenance
and do-it yourself (section 8)” of your Owner’s Manual.
01
02
03
04
05
F
E
07
08
06

Outside Mirror Control Switch
To select the right or left side mirror, turn the control
switch

01 right or left.

To adjust the mirror angle, move the control switch

01 up, down, right or left.

To prevent accidentally moving the mirror, turn and
set the switch to the middle “neutral” position.
REVERSE TILT-DO wN FEATURE

when backing up the vehicle, the right or left outside mirror can be selected to automatically turn
downward to provide better rear visibility.
1. Push the ignition switch to the ON position.
2. Move the shift lever to the r (rEVErSE) position.
3. choose the right or left outside mirror by operating the outside mirror control switch

01 .
4. The selected outside mirror surface moves downward.

when one of the following conditions has occurred, the outside mirror surface will return to its
original position:

• The shift lever is moved to any position other than r (rEVErSE).
• The outside mirror control switch is set to the center “neutral” position.
• The ignition switch is pushed to the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
6
first drive features
Automatic Drive Positioner (if so equipped)

Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner memory.

Follow these procedures to set the memory positions:
• Confirm the shift lever is in the P (PArk) position.
• Push the ignition switch to the ON position.
• Adjust the driver’s seat, steering column and outside mirrors to the desired positions using
the adjusting switches for each feature.
• Push the SE t switch and within 5 seconds, push the memory switch (1 or 2) for at least
1 second.
• The indicator light on the memory switch you select will illuminate for approximately 5 seconds.
• The driver’s seat, steering column and outside mirror positions are now set to your preference.

These memorized positions can also be linked to your INFINITI Intelligent Key™.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
01

7
Starting/Stopping the Engine
NOTE: It is important to make sure the INFINITI Intelligent
Key™ is with you (that is, in your pocket or purse).

Depress the brake pedal.
• If the brake pedal is not depressed, pushing the
ignition switch once enters the ACC mode.
• If the ignition switch is pushed a second time, the
vehicle will enter the ON mode.

Move the shift lever to P (PArk).

Push the ignition switch to start the engine.
TURNING THE ENGINE OFF

Move the shift lever to the P (PArk) position and apply the parking brake.

Press the ignition switch S tArt/S tOP button to turn the engine off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Headlight Control Switch
HEADLIGHT c ONTROL

Turn the headlight control switch to the position

01 to turn on the front parking, side marker, tail, license
plate and instrument panel lights. Turn the switch to the


position
02 to turn on the headlights.
AUTOLIGHT SYSTEM

The autolight system will automatically turn the headlights on when it is dark and off when it is
light. The system will keep the headlights on for a period of time after you turn the ignition off
and all doors are closed.

To activate the autolight system, turn the headlight control switch to the AU tO position
03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight

control switch to the OFF,

01 or
position
02 .

HIGH BEAM SELE cT

Push the headlight control switch forward
04 to
select the high beam function. The blue indicator
light
illuminates in the instrument panel. Pull
the headlight switch back to the original position to
select the low beam. The blue indicator light goes off.

Pull and release the headlight control switch
05 to
flash the headlight high beams on and off.
03
01
02
04
05