2013 FIAT 500 ABARTH turn signal bulb

ON/RUN or START position. If the key is in the OFF/
LOCK position, or not in the ignition, the air bag system
is not on and the air bags will not inflate.
The ORC contains a backup power supply system that
may deploy the air bags even if the battery loses power or
it becomes disconnected prior to deployment.
Also, the ORC turns on the Air Bag Warning
Light in the instrument panel for approxi-
mately four to eight seconds for a self-check
when the ignition is first turned on. After the
self-check, the Air Bag Warning Light will turn off. If the
ORC detects a malfunction in any part of the system, it
turns on the Air Bag Warning Light, either momentarily
or continuously. A single chime will sound if the light
comes on again after initial startup.
It also includes diagnostics that will illuminate the instru-
ment cluster Air Bag Warning Light if a malfunction is
noted that could affect the air bag system. The diagnos-
tics also record the nature of the malfunction.
WARNING!
Ignoring the Air Bag Warning Light in your instru-
ment panel could mean you won’t have the air bags
to protect you in a collision. If the light does not come
on as a bulb check when the ignition is first turned
on, stays on after you start the vehicle, or if it comes
on as you drive, have an authorized studio service the
air bag system immediately.
Driver And Passenger Advanced Front Air Bag
Inflator Units
The Driver and Passenger Advanced Front Air Bag
Inflator Units are located in the center of the steering
wheel and on the right side of the instrument panel.
When the ORC detects a collision requiring the Ad-
vanced Front Air Bags, it signals the inflator units. A large
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47

▫Appearance Care And Protection From
Corrosion...........................336
!FUSES..............................342
▫Interior Fuses........................342
▫Underhood Fuses......................345
!VEHICLE STORAGE....................348
!REPLACEMENT BULBS.................348
!BULB REPLACEMENT..................349
▫Headlamps Low beam and High beam......350
▫Front Turn Signal, Parking And Daytime Running
Lamps.............................350
▫Front Fog Lamps......................351
▫Front/Rear Side Marker Lamps............351
▫Rear Tail, Stop, Backup And Turn Signal
Lamps.............................352
▫Center High Mounted Stop Lamp (CHMSL) . . .352
!FLUID CAPACITIES....................353
!FLUIDS, LUBRICANTS AND GENUINE PARTS . .353
▫Engine.............................353
▫Chassis............................354
308 MAINTAINING YOUR VEHICLE

Exterior Bulbs
Bulb Number
Front Low and High
Beam Headlamp
HIR2
Front Parking/Daytime
Running Lamps
W21/5W
Front Fog Lamps H11
Front Side Marker Lamps W3W
Front Turn Signal Lamps WY21W
Side Direction Lamps W5W
Rear Turn Signal Lamps PY21W
Rear Side Marker Lamps W3W
Rear Tail and Stop
Lamps
PY21W/5W
Rear Backup Lamps W16W
Bulb Number
Center High Mounted
Stop Lamp
W5W
License Plate Lamps LED (See Authorized stu-
dio)
NOTE:Numbers refer to commercial bulb types that
can be purchased from your authorized studio.
If a bulb needs to be replaced, visit your authorized
studio or refer to the applicable Service Manual.
BULB REPLACEMENT
NOTE:Lens fogging can occur under certain atmo-
spheric conditions. This will usually clear as atmospheric
conditions change to allow the condensation to change
back into a vapor. Turning the lamps on will usually
accelerate the clearing process.
7
MAINTAINING YOUR VEHICLE 349

Headlamps Low beam and High beam
1. Remove the plastic cap from the back of the headlamp
housing.
2. Rotate the bulb counter-clockwise.
3. Remove the bulb and replace as needed.
4. Install the bulb and rotate clockwise to lock in place.
5. Reinstall the plastic cap.
Front Turn Signal, Parking And Daytime Running
Lamps
1. Turn the steering wheel completely to the left or right.
2. Open the wheel housing access door.
3. Remove the plastic cap from the back of the lamp
housing.
4. Rotate bulb/socket counter-clockwise.
5. Remove the bulb and replace as needed.
350 MAINTAINING YOUR VEHICLE

Rear Tail, Stop, Backup And Turn Signal Lamps
1. Open the liftgate.
2. Remove the two screws and remove the tail lamp
assembly.
3. Remove the four screws (using a T20 driver) and
separate the backplate from the lamp housing.
4. Remove the tail, stop, or turn signal bulbs by pushing
them slightly and turning counter-clockwise.
5. Remove the backup lamp bulb by pulling straight out.
6. Replace lamps as required and reinstall lamp.
Center High Mounted Stop Lamp (CHMSL)
1. Remove the two guard caps and the two fastening
screws.
2. Remove the center high mounted stop lamp assembly.
3. Disconnect the electric connector.
4. Press the retaining device and open the bulb holder.
5. Remove the snap-fitted bulb to be replaced and re-
place it.
6. Close the back cap locking it properly.
7. Reinstall the two fastening screws and reinstall the
guard caps.
352 MAINTAINING YOUR VEHICLE

Hood................................109
Lead Free Gasoline........................272
Leaks, Fluid..............................83
Life of Tires.............................262
Liftgate (Sedan)...........................25
Light Bulbs..............................83
Lights..................................83
Airbag................................47
Anti-Lock.............................154
Brake Assist Warning....................244
Brake Warning.........................153
Bulb Replacement.......................349
Engine Temperature Warning...............152
Exterior...............................83
Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..147
High Beam............................113
High Beam Indicator.....................147
Low Fuel.............................147
Malfunction Indicator (Check Engine).........151
Oil Pressure...........................151
Park.................................113
Seat Belt Reminder......................148
Service...............................349
Service Engine Soon (Malfunction Indicator) . . . .151
Tire Pressure Monitoring (TPMS)............149
Traction Control........................244
Turn Signal............................83
Voltage..............................148
Wait to Start...........................146
Warning (Instrument Cluster Description)......146
Loading Vehicle
Ti re s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..252
Locks
Automatic Door.........................23
Door.................................20
Power Door............................22
Lubrication, Body.........................322
378 INDEX