2013 Citroen C4 PICASSO RHD display

165
4
Driving
SymbolAssociated messageComments
" SYSTEM INACTIVE: S
peedunsuitable"If the speed of your vehicle is outside the operating range.
Where the speed is not suitable, a message is displayed while the speed is outside limits(below 42 mph (70 km/h) or above 93 mph (15 0 km / h), approximately). However, when
decelerating, the system is deactivated below 27 mph (45 km/h).
" System deactivated
"
On deactivating the function, in "DRIVING" display mode.
"
SYSTEM INACTIVE:Visibility reduced"The system switches to standby automatically if the sensor does not detect the vehicle in front correctly (very difficult weather conditions, sensor out of adjustment, ...).

166
Driving
The vehicle being followed may not be detected
in cer tain conditions such as, for example:
- when turnin
g,
- when changing lane,
- when the vehicle in front is out of the range
of the sensor (maximum range: around
100 m).
Operating limits
In the event of a fault with the system,
this warning lamp is displayed
accompanied by a message.

Operating fault

Have the system checked by a CITROËN
dealer or a qualified workshop.

At the first use of the system after repair, a message may be displayedindicating that the system is initialising. The system is not available while this is in progress. As soon as the message disappears the system is operationalagain. If the message does notdisappear, contact a CITROËN dealer or a qualified workshop.


The operation of the radar, located in the front bumper, may be disturbed by accumulations of grime (dust, mud...) or in certain weather conditions (snow, ice...).
The message "SYSTEM INACTIVE:Visibility reduced" is displayed to signal that the system has been put intostandby.
Clean the front bumper regularly.

168
Driving

Steering mounted controls


The information is grouped together in the
instrument panel.
6
. Speed limiter on / pause indication.
7. Speed limiter mode selection indication. 8. Speed value setting.






Speed limiter
Once the programmed speed limit is reached, additional pressure on the accelerator pedal has no effect.


The speed limiter cannot, in any circumstances,replace the need to observe speed limits, nor can it replace the need for vigilance and responsibility on the par t of the driver.
System which prevents the vehicle fromexceeding the speed programmed by the driver.

The controls are
grouped together at the
steering wheel.
1.Speed limiter mode selection wheel.
2. Value decrease button. 3.
Value increase button.
4.Speed limiter on / pause button.
5.List of memorised speeds display button.

Displays in the instrument panel
The speed limiter is switched onmanually:
it requires a programmed speed of at least
20 mph (30 km/h).
The speed limiter is paused
by operation of the control.
The programmed speed can be exceeded
temporarily by pressing the accelerator firmly
beyond the point of resistance.
To return to the programmed speed, simply release the accelerator pedal until the vehicle returns to the programmed speed limit.
The programmed speed remains in the memory when the ignition is switched off.

F
or more information on the list of memorisedspeeds, refer to the "Memorising speeds"
section.

169
4
Driving
)Turn wheel 1 to the "LIMIT"
position: thespeed limiter mode is selected but is notswitched on (Pause).)Switch the speed limiter back on bypressing button 4
, if the speed displayed
is suitable (by default, the last speedprogrammed).)You can temporarily stop the the speed limiter by pressing button 4 again: the
display confirms that it has been stopped(Pause).

You do not have to switch the speed limiter on
in order to set the speed.Once the function is selected, you can modify
the speed setting by:
- using buttons 2
and 3
, increasing or decreasing the speed displayed: )
by successive short presses, to modifyby + or -

170
Driving
On sharp acceleration, as when descending a steep hill, the speedlimiter will not be able to prevent thevehicle from exceeding the programmedspeed.
The limiter is temporarily deactivated and the displayed programmed speed flashes. An audible signal accompanies the flashing of the programmed speed when exceeding the speed is not due to an action by the driver.
The use of mats not approved by CITROËN may interfere with theoperation of the speed limiter.
To a v o i d a ny risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- do not fit one mat on top of another.


Flashin
g of the dashes indicates a fault with the
speed limiter.
Have it checked by a CITROËN dealer or aqualified workshop.


Operating fault
)Press firmly
on the accelerator pedal,going beyond the point of resistance,
toexceed the programmed speed limit.The speed limiter is deactivated temporarilyand the displayed programmed speed flashes.
An audible signal accompanies the flashing
of the programmed speed when exceeding
the speed is not due to an action by the driver (steep hill...).
As soon as the vehicle's speed returns to the programmed value, the limiter operates again:
the display of the programmed speed becomes steady again.
Switching off Te m p o r a r i l
y exceeding
the programmed speed
)Turn wheel 1to the "0"
position.
The display of information related to the
speed limiter disappears.

171
4
Driving
Steering mounted controls
The information is grouped together in the instrument panel.
6. Cruise control pause / resume indication.
7.Cruise control mode selection indication. 8.Speed value setting.






Cruise control

System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.


The cruise control system cannot, in any circumstances, replace the need to obser ve speed limits, nor can it replace the need for vigilance and responsibility on the par t of the driver.
You are advised to keep your feet near the pedals at all times.
Th
e cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph
(40 km/h) and engagement of:


- at least four th gear on a manual gearbox,

- second gear on an electronic or automatic gearbox, in manual driving mode,

- position A
on an electronic gearbox or D
on an automatic gearbox.
The controls o
f this system are grouped
together at the steering wheel. 1.Cruise control mode selection wheel.
2. Decrease value or speed setting on the flybutton.3.
Increase value or speed setting on the flybutton.
4. Cruise control pause / resume button.
5. Memorised speeds display button.
For more information on the list of memorisedspeeds, refer to "Memorising speeds" section).


Displays in the instrument panel

Switching off the ignition cancels any programmed speed value. Th
e cruise control is paused
manually or
by pressing the brake or clutch pedal or
on triggering of the ESP system for safety
reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal until the programmed cruise speed is reached again.

172
Driving
If the cruise control is on, you can then modify
the initial speed in one of the following ways:


- using buttons 2
or 3
: )
by successive shor t presses, to modify
the speed by + or - 1 mph (km/h), )
by a long press, to modify the speed insteps of + or - 5 mph (km/h),
)Turn wheel 1to the "CRUISE"position: thecruise control mode is selected but is not
switched on (Pause).)Press button 2 or 3
: your vehicle's current
speed becomes the cruise speed (selected
on the fly).
The cruise control is activated (ON).

Modifi cation of the initial speed
setting


- pressing button 5:)the six memorised speeds are displayed
in the touch screen tablet,
)choose a value: it is displayed in the
instrument panel.
Th
e selection screen closes after a fewmoments.
The modification is then accepted.
Pause
Once switched on, you can pause the cruisecontrol at any time by pressing button 4
:
the screen confirms the pause.

173
4
Driving
Flashing of the dashes indicates a fault with thecruise control.
Have it checked by a CITROËN dealer or aqualified workshop.
Operating fault

Exceeding the programmed
speed
If the programmed speed is exceeded, the
displayed speed flashes.
Once the vehicle returns to the programmedspeed, the display becomes steady again.

Switching off
)Turn wheel 1
to the "0"position.
The display of information related to the cruise control disappears.



When the cruise control is switched on,be careful if you maintain the pressure on one of the programmed speedchanging buttons: this may result in avery rapid change in the speed of your vehicle.
Do not use the cruise control on slippery roads or in heavy traffic. On a steep descent, the cruise control will not be able to prevent the vehicle from exceeding the programmed speed. On steep climbs or when towing, the programmed speed may not be reachedor maintained.
The use of mats not approved byCITROËN may inter fere with the
operation of the cruise control.
To avoid any risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- never fit one mat on top of another.