2013 Citroen C3 RHD wheel bolts

Practical information
152














Changing a wheel
The tools are installed in the boot under the
floor.
To gain access to them: )open the boot, )raise the floor,)remove the polystyrene storage box,)unclip and remove the box containing the
tools.
Access to the tools
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.

List of tools

All of these tools are specific to your vehicle. Do not use them for other purposes.
1.Wheelbrace.
For removing the wheel trim and removal of
the wheel fixing bolts. 2. Jack with integral handle.
For raising of the vehicle. 3. "Bolt cover" tool.
For removing the bolt protectors (covers)on alloy wheels. 4.Socket for the security wheel bolts (located
in the glove box).
For adapting the wheelbrace to the special "security" wheel bolts (if your vehicle has
them).

11
Practical information
153

Wheel with trim
When removing the wheel
, firstdetach the trim using the wheelbrace 1pulling at the valve passage hole. When refitting the wheel
, refit thetrim star ting by placing its cut-out at the valve and press around its edge withthe palm of your hand.

Access to the spare wheel
The spare wheel is installed in the boot under
the floor.
According to country, the spare wheel may be steel or of the "space-saver" type.
To gain access to it, refer to the paragraph
"Access to the tools" on the previous page.
Fitting the steel or "space-saver" type spare wheel

If your vehicle is fitted with alloy wheels, it is normal to notice, when tightening the bolts on fitting, that the washers donot come into contact with the steel or "space-saver" type spare wheel. Thewheel is secured by the conical contactof each bolt.

11
Practical information
155
Removing a wheel

List of operations
)
Remove the bolt cover from each of the bolts using the tool 3(with alloy wheels
only).) Fit the security bolt socket 4
on thewheelbrace 1to slacken the security bolt(if your vehicle has them).)
Slacken the other bolts using the
wheelbrace 1only.
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level,stable and not slippery. Apply the parking brake, switch off theignition and engage first gear *
to lock the wheels. If necessary, place a chock under thewheel diagonally opposite the wheel to be changed. It is imperative that you ensure that the occupants get out of the vehicle andwait where they are safe.Never go underneath a vehicle raisedusing a jack; use an axle stand.
*
position R
for an electronic gearbox; position P
for an automatic gearbox.

Practical information
156
Place the jack 2 in contact with one of the
two front A or rear Blocations provided on
the underbody, whichever is closest to the
wheel to be changed. )Extend the jack 2 until its base plate is in contact with the ground. Ensure that thecentreline of the jack base plate is directly below the location A
or Bused.
)
Raise the vehicle until there is sufficient space between the wheel and the ground
to admit the spare (not punctured) wheeleasily. ) Remove the bolts and store them in a clean
place.
) Remove the wheel.

11
Practical information
157

List of operations
)
Put the wheel in place on the hub. )
Screw in the bolts by hand. )
Pre-tighten the security bolt (if your vehiclehas them) using the wheelbrace 1
fitted
with the security bolt socket 4.
)
Pre-tighten the other bolts using the
wheelbrace 1only.

Fitting a wheel
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. When using the "space-saver" typetemporary use spare wheel, do notexceed 50 mph (80 km/h).Have the tightening of the bolts and thepressure of the spare wheel checkedby a CITROËN dealer or a qualified workshop without delay. Have the punctured wheel repaired and replace it on the vehicle as soon aspossible.Do not drive with more than one temporary use spare wheel fitted to the vehicle at one time.

Practical information
158
Tighten the security bolt (if your vehicle has
them) using the wheelbrace 1 fitted with thesecurity bolt socket 4
. )
Tighten the other bolts using the
wheelbrace 1 only.)
Refit the bolt covers on each of the bolts. )
Store the tools in the box.
)Lower the vehicle fully. )Fold the jack 2
and detach it.

11
Practical information
185
"Comfort" sun blinds, door deflectors, insulated module, smoking kit, fragrance car tridges, front centre
armrest, moveable mirror, reading lamp, front and rear parking sensors, cup holder, coat hanger for head restraint, solar film for
windows, security film for windows...
"Security and safety":
anti-theft alarm, wheel security bolts, stolen
vehicle tracking system, breathalyser, first aid
kit, warning triangle, high visibility vest, dog
guard, snow chains, non-slip covers, foglamps
kit, child seats and booster cushions, pet
transpor t protectors...


Conversion kits

You can obtain an "Enterprise" kit to conver t a
trade vehicle to a private car and vice-versa.

"St
yle":leather steering wheel, gear lever knobs,front spoiler, rear diffuser, bumper trims, front foglamp trims, parking brake lever trims, aluminium footrest, alloy wheels, wheel trims, chrome tailgate finisher, chrome tailpipe finisher, chrome mirror shells, chrome door
handles...
"Transport solutions":boot tray, boot carpet, boot net, bootcontainers, transverse roof bars, bicycle carrier,
ski carrier, roof boxes, towbars, towbar wiring
harnesses...





Accessories A wide range of accessories and genuine par ts is available from the CITROËN dealer network.
These accessories and par ts have been tested and approved for reliability and safety.
They are all adapted to your vehicle and benefit from CITROËN's recommendation and warranty.

*
To avoid any risk of jamming of the pedals:
- ensure that the mat is positioned and
secured correctly,
- never fit one mat on top of another.
"Protection":
mats * , mudflaps, seat covers, door sillprotectors, bumper protection strips, vehicleprotective cover, side protectors, boot mat, boot
liner...
If a towbar and wiring are fitted outsidethe CITROËN dealer network, this must be done making use of the vehicle's electrical pre-equipment and followingthe manufacturer's recommendations.