2013 Citroen C3 PICASSO RHD warning

1
Monitoring
33
Engine oil level indicator
This information is displayed for a few seconds
when the ignition is switched on, after theservice information.
Oil level correct
Oil level low
Oil level indicator fault

Dipstick
This is indicated by the flashing of "OIL", linked with the ser vice warning lamp, accompanied
by an audible signal and a message in themultifunction screen.
If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to
prevent damage to the engine. This is indicated by the
flashing of "OIL--"
. Contact a CITROËN dealer or a qualified
workshop.
Re
fer to the "Checks" section to locate the
dipstick and the oil filler cap on your engine.
Th
ere are 2 marks on the
dipstick:-A= max; never exceed thislevel (risk of damage to the engine), - B= min; top up the level via
the oil filler cap, using thegrade of oil suited to your engine.
The level shown will only be correctif the vehicle is on level ground and the engine has been off for more than 30 minutes. S
ystem to inform the driver of whether theengine oil level is correct or not.

2
Multifunction screens
35













Monochrome screen A
Controls

Displa
ys in the screen

This displays the following information:


- time,

- date,

- ambient temperature
(this flashes if there isa risk of ice),

- state of the openings (doors, boot, ...),

- audio sources (radio, CD, ...),

- trip computer (refer to the end of the section).
Warning messages or information messagesmay appear temporarily. These can be cleared
by pressing the "Back"button.


Main menu
)
Press the "MENU"
button for access to
the main menu
, then press the "  " or " " buttons to scroll through the variousmenus:
- radio-CD,
- vehicle configuration,
- options,
- displa
y settings,
- language,
- units.)
Press the "OK"button to select the menurequired.
From the audio equipment control panel, youcan: )
press the "MENU"
button for access to themain menu
, )
press the " 
" or " " buttons to scroll
through the items on the screen, ) press the "MODE"
button to change the
permanent application (trip computer, audiosource, ...),) press the "  " or " " buttons to change asetting value,)
press the "OK"button to confirm,or )
press the "Back"button to abandon the
operation in progress.



Radio-CD
With the audio equipment switched on, once
the "Radio-CD" menu has been selected youcan activate or deactivate the functions linkedwith use of the radio (RDS, REG) or the CD(introscan, shuffle, CD repeat).
For more information on the "Radio- CD"
application, refer to the "Audio s
ystem" section.

Multifunction screens
38







Monochrome screen A associated with the eMyWay satellite
navigation colour screen
This displays the following information:
- ambient temperature (this flashes if there isa risk of ice),
- trip computer (refer to the end of the
section).
Warning messages or information messagesmay appear temporarily. These can be cleared
by pressing the "Back"
button.


Controls

There are three display control buttons:


- "Back"
to abandon the operation in
progress,-"MENU"to scroll through the menus or sub-menus, -"OK"
to select the menu or sub-menu
required.


Main menu
)Press the "MENU"
button to scroll through
the various menus of the main menu:- vehicle configuration,
- options,
- language,
- units. )Press the "OK"button to select the menurequired.
Displays in screen A

Multifunction screens
42

"Trip computer" menu
Alert log
This summarises the active warning messages,
displaying them in succession in the multifunction screen. Once this menu has been selected,
you canconsult information concerning the status of the
vehicle (alert log, status of functions, etc.)

Defi ne the vehicle parameters
Once this menu has been selected, you can
activate or deactivate the following systems:


- wiper linked with reverse gear (refer to the
"Visibility" section),

- daytime lighting, (refer to the "Visibility" section),

- "guide-me-home" lighting


"Personalisation-
Confi
guration" menu
Once this menu has been selected, you can gain access to the following functions:


- define the vehicle parameters,

- display configuration,

- choice of language. Status of functions
This summarises the status (active or inactive)of the vehicle's functions.
Enter distance to destination
This allows you to enter an approximate
distance until your final destination.
)
Press the "MENU"button for access to the
main menu. ) Press the arrows, then the "OK"
button toselect the " Tr ip computer " menu.
)
In the " Tr ip computer "menu, select one of the following applications:

Access
66
Locating your vehicle
)Press the closed padlock to locate your locked vehicle in a car park.
This is indicated by lighting of the cour tesylamps and flashing of the direction indicators for a few seconds.


Electronic engine immobiliser

The key contains an electronic chip which has
a special code. When the ignition is switched
on, this code must be recognised in order for
starting to be possible.
This electronic engine immobiliser locks theengine management system a few minutes
after the ignition is switched off and prevents
starting of the engine by anyone who does not have the key.
Anti-theft protection
In the event of a fault, you are
informed by illumination of this
warning lamp, an audible signal and a message in the screen.
Folding the key
)First press this button to fold the key.
If you do not press the button when foldingthe key, there is a risk of damage to the mechanism.

Ignition switch



- Position 1: Stop

- Position 2: Ignition

- Position 3: Starting


Starting the vehicle
)Inser t the key in the ignition switch.
The system recognises the star ting code. )Turn the key fully towards the dashboard toposition 3 (Starting).)When the engine starts, release the key. In this case,
your vehicle will not start; contact
a CITROËN dealer as soon as possible.
Keep safely the label attached to the keys given
to you on acquisition of the vehicle.

Access
70

Reinitialisation
Deactivating the rear window and door controls
)
For the safety of your children, press switch 5to prevent operation of the rear
windows irrespective of their position.
With the indicator lamp on, the rear controls aredeactivated.
With the indicator lamp off, the rear controls are
activated.
When the
function is activated,
this warning lamp lights up on the
instrument panel for a few seconds.
This control also deactivates the interior rear door controls (see "Child safety -Electric child lock" section).
In the event of contact during operationof the windows, you must reverse the movement of the window. To do this,press the switch concerned.
When the driver operates the passenger
electric window switches, they mustensure that no one is preventing correct closing of the windows.
The driver must ensure that the passengers use the electric windowscorrectly.
Be aware of children when operating the windows.
Safety anti-pinch
The one-touch electric windows are fitted with a safety anti-pinch function.When the window rises and meets an obstacle, it stops and partially lowers again.

In the event of unwanted opening of thewindow on closing (for example in the presence of frost): )press the switch until it opens completely, )then pull it immediately until itcloses,)continue to hold the switch for approximately one second after thewindow has closed.
The safety anti-pinch function is not active during these operations.

In the event of a malfunction you must reinitialise
the o
peration of the electric windows: )release the switch and pull it again until the
window closes completely, )hold the switch for approximately onesecond after closing,
)press the switch to lower the window automatically. The safety anti-pinch function is not active
during these operations. Always remove the key from the ignition when
leaving the vehicle, even for a shor t time.

4
Access
71











Doors


From outside
)After unlocking the vehicle using theremote control or the key, pull the door handle.
From inside
)
Pull the front door control to open the door;
this unlocks the vehicle completely. ) Pull the rear door control to open the door;
this unlocks only the door opened.

Closing
-when the engine is running
, this
warnin
g lamp comes on, accompanied
by a message in the multifunction screen for a few seconds,

Opening

When a door is not closed correctly:

- when the vehicle is movin
g
(speed higher than 6 mph (10 km/h)), this warning
lamp comes on, accompanied by an
audible signal and a message in the multifunction screen for a few seconds.

Access
74
)After unlocking the vehicle using theremote control or the key, pull the handleand raise the tailgate.











Boot
- when the engine is running
, this
warning lamp comes on, accompanied
by a message on the multifunction
screen for a few seconds,
Tailgate release

Unlocking
)Fold back the rear benchseat to gainaccess to the lock from inside the boot. )Insert a small screwdriver into hole Aof thelock to unlock the tailgate.




Closing

If the tailgate is not closed correctly:
Opening
-when the vehicle is moving
(speed above 6 mph (10 km/h)), this warning lamp comeson, accompanied by an audible signal anda message on the multifunction screen for a few seconds.

)
Lower the tailgate using the interior grab handle.
System for mechanical unlocking of the boot
in the event of a battery or central lockingmalfunction.