In o rder for the airbag to offer protection, it is
important t hat all vehicle occupants, especia l
l y any children, who must be in the front seat
because of exceptional circumstances, be
pro perly restrained and as far away from the
airbag as poss ible. By keep ing room between
the child's body and the front of the passen
ger c om partment, the airbag can inflate com
p letely and provide supp lemental p rotection
in certa in frontal col lis ions.
A WARNING
Not using a booster seat, us ing the boos
ter seat improperly, incorrect ly installing a
booster seat or using the vehicle safety
belt improperly increases the risk of seri
ous personal injury and death in a collision
or other emergency s ituation. To help re
duce the risk of ser ious personal injury
and/or death:
- The shoulder be lt must lie as close to the
center of the child's co llar bone as poss i
ble and must lie and snug on the upper
body.
It must never lie across the throat
o r neck. The lap belt must l ie across the
pelvis and never across the s tomach o r
abdomen. Make sure the belt lies flat
and snug. Pull on the be lt to tighten if
necessary.
- Failure to properly route safety belts
over a child's body will cause severe inju
ries in an acc ident or other emergency
situation
¢page 100.
-Children on the front seat of any car,
even with Advanced A irbags, can be seri
ous ly injured or even killed when an a ir
bag inflates.
- Never let a child stand or knee l on any
seat, for examp le the front seat.
- Never let a child ride in the ca rgo area of
your vehicle.
- Always remember that a ch ild lean ing
forward, sitt ing s ideways or out of posi
t ion in any way during an acc ident can be
struck by a deploying airbag . This will re
sult in se rious personal injury or death.
- If you must install a booster seat on the
front passenger seat because of excep-
-
Child Sa fet y 139
tional circ umstances the PASSENGER
AIR BAG OFF
li ght m ust come on and
stay on, whenever the ignition is switch
ed on .
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, perform
the checks descr ibed
¢ page 119, Moni
toring the Advanced Airbag System .
-Take the chi ld restraint off the front pas
senger seat and install it prope rly at one
of the rear seat positions if the
PASSEN
GER AIR BAG OFF
lig ht does not stay on
wheneve r the ignit ion is swi tched on.
- Always read and heed all WAR NINGS
wheneve r us ing a child res trained in ave
hicle is being used
¢page 100, Safety
belts,
¢ page 108, Airbag system and
¢ page 130, Important things to know .
Booster seats on the rear seat
Children who are about 7 years and older, who
weigh mo re than SS lbs . (25 kg) and are not
ta ller than 4'11" (1.5 m) are best protected
when properly rest rained on the rear seat.
D ue to limited rear seat head clearance c hil
dren 4'3" (1.3 m) and taller must not use
booster seats o n the rear seat of your Aud i TT
Coupe. The rear seat of your Audi TT Coupe
has been specially designed to permit ch ildren
who are betwee n 4'3" ( 1.3 m) and 4'11" ( 1.5
m) tall (about 7 to 12 years old) to use the
available th ree -point lap and s hou lde r safety
belts.
A WARNING
~ -
- T he rear sea t area is too sma ll to safely
transport passengers tal le r than 4 '11"
(1.5 m).
- Persons taller than 4'11" (1. 5 m) as well
as children in booster seats who are too
close to the rear window and roof can
suffer severe head and neck inju ries
when t he rear lid is closed or in a crash.
- The minimum clearance between the
passengers' heads and the rear w indow
•
•
interior. The child can be seriously in
jured or killed.
- Never install rear-facing child safety
seats or infant carriers on the front pas
senger seat. A child will be seriously in
jured and can be killed when the passen ger airbag inflates .
- The inflating airbag will hit the child
safety seat or infant carrier with great
force and will smash the child safety seat
and child against the backrest, door or
roof.
- Always install rear-facing child safety
seats or infant carriers on the rear seat.
- Forward -facing child safety seats or in
fant carriers installed on the front pas
senger's seat may interfere with the de
ployment of the airbag and cause serious
injury to the child.
-It is safer to install a forward-facing
child safety seat on the rear seat.
- Always read and heed all WARNINGS
whenever using a child restrained in ave
hicle is being used~
page 130. Special
precautions apply when installing a child
safety seat on the front passenger seat
~ page 110, Child restraints on the front
seat -some important things to know.
_&. WARNING
Always take special precautions if you
must install a forward or rearward-facing
child restraint on the front passenger's
seat in exceptional situations:
- Whenever a forward or rearward-facing
child restraint is installed on the front
passenger seat, the
PASSENGER AIR
BAG OFF
light must come on and stay on
whenever the ignition is switched on.
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, perform
the checks described
~page 119, Moni
toring the Advanced Airbag System.
- Take the child restraint off the front pas
senger seat and install it properly at one
of the rear seat positions if the
PASS EN-
Child Safety 141
GER AIR BAG OFF light does not stay on
whenever the ignition is switched on.
- Improper installation of child restraints
can reduce their effectiveness or even
prevent them from providing any protec
tion.
-An improperly installed child restraint can interfere with the airbag as it deploys and seriously injure or even kill the
child.
- Always carefully follow the manufactur
er's instructions provided with the child
safety seat or carrier.
- Never place additional items on the seat
that can increase the total weight regis
tered by the weight-sensing mat and can cause injury in a crash.
_&. WARNING
Forward-facing child restraints:
- Always make sure the forward-facing
seat has been designed and certified by
its manufacturer for use on a front seat
with a passenger front and side airbag.
- Never put the forward-facing child re
straint up, against or very near the in
strument panel.
- Always move the passenger seat into its
rearmost position in the seat's fore and
aft adjustment range, as far away from
the airbag as possible before installing
the forward-facing child restraint. The backrest must be adjusted to an upright
position.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched
on .
_&. WARNING
Rearward-facing child restraints:
- A child in a rearward-facing child safety
seat installed on the front passenger
seat will be seriously injured and can be killed if the front airbag inflates - even
with an Advanced Airbag System .
•
•
142 Child Safety
-The inflating airbag will hit the child
safety seat or infant carrier with great
force and will smash the child safety seat and child against the backrest, door or
roof.
- Always be especially careful if you must
install a rearward facing child safety seat
on the front passenger seat in exception
al circumstances.
-A tight tether strap on a rearward-facing child restraint attached to the front pas
senger seat can put too much pressure
on the weight-mat in the seat and regis
ter a heavier weight in the Advanced Air
bag System. The heavier weight regis
tered can make the system work as
though an adult were on the seat and de
ploy the Advanced Airbag when it must
be suppressed causing serious or even
fatal injury to the child .
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched on .
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, immedi
ately install the rear-facing child safety
seat in a rear seating position and have
the airbag system inspected by your Audi
dealer.
Activating the convertible locking retractor
Use the convertible locking retractor to se
cure a child restraint.
Always heed the child safety seat manufactur
er's instructions when installing a child re
straint in your vehicle. To activate the conver
tible lock ing retractor :
"' Place the child restraint on a seat, prefera
bly on the rear seat .
... Slowly pull the belt
all the way out.
... Route it around or through the child re
straint belt path
c:> ,& .
... Push the child safety seat down with your
full weigh t to get the safety belt really tight. "'
Insert the belt tongue into the buckle for
that seating position .
"' Guide the safety belt back into the retractor
until the belt lies flat and snug on the child
safety seat.
... You should hear a "clicking" noise as the
belt winds back into the inertia reel. Test the
convertible locking retractor by pulling on
the belt. You should no longer be able to
pull the belt out of the retractor. The con
vertible locking retractor is now activated.
... Make sure that the red release button is fac
ing away from the child restraint so that it
can be unbuckled quickly.
"' Pull on the belt to make sure the safety belt
is properly tigh t and fas tened so tha t the
seat cannot move forward or sideways more
than one inch (2.5 cm) .
A WARNING
Using the wrong child restraint or an im
properly installed child restraint can cause
serious personal injury or death in a crash.
-Always make sure that the safety belt re-
tractor is locked when installing a child
safety seat. An unlocked safety belt re
tractor cannot hold the child safety seat
in place during normal driving or in a
crash.
- Always buckle the child safety seat firmly
in place even if a child is not sitting in it.
A loose child safety seat can fly around
during a sudden stop or in a crash.
- Always make sure the seat backrest to
which the child restraint is installed is in
an upright position and securely latched
into place and cannot fold forward . Oth
erwise, the seatback with the child safety
seat attached to it could fly forward in
the event of an accident or other emer
gency situation.
- Always read and heed all WARNINGS
whenever using a child restrained in ave
hicle is being used
c:> page 130. Special
precautions apply when installing a child
safety seat on the front passenger seat
c:> page 110, Child restraints on the front
seat -some important things to know.
-
the exhaust system and this could cause
the catalytic converter to overheat.
- Do not turn off the ignition while the ve
hicle is moving .
- Do not con tinue to operate yo ur vehicle
under these conditions, as otherwise fuel
can reach the cata lytic converter . This
could result in overheating of the con
verter, requ iring its replacement.
- To assure efficient operation of the Emis
sion Control System:
- Have your veh icle ma inta ined properly
and in acco rdance with the service rec
ommendations in your Wa rranty
&
Ma intenan ce booklet.
- Lac k of proper maintenance as well as
improper use of the vehicle will impa ir
t he funct ion of the emission control
system and cou ld lead to damage.
@ For the sake of the environment
Even when the Emission Contro l System is
operating p roperly, the exhaus t gas can
have a s ulfu r- like exhaust gas smell under
some operating states. This depends on
the s ulfur content o f the fue l being used.
Using a different brand of fuel may help,
or filling the tank w ith lead-free super
grade gasoline .
Operate your vehicle
economically and
minimize pollution
General
Your personal style of driving will determine
the economy of your vehicle, as well as ex
haust and noise levels .
Fuel economy, environmental impact, and
wear on your engine, brakes and t ires largely
depend on three factors :
- your persona l driving style
- operating conditions
- technical lim itations
I f you anticipate w hat you need to do nex t and
d rive economically, you can eas ily cut your
Dri vin g and en vironm ent 161
fuel consumption by 10 -15 percent. Th is sec
tion w ill give yo u some tips on how you can
help the env ironment and your pocketbook .
(D Tips
The cons umption estimates as published
by ENVIRONME NTAL PROTEC TION AGENCY
(EPA) and Transport Canada may not corre
spond to your actual consumption on the road, which will vary depending upon vehi
cle load and speed, road and weather con
dit ions, trip length, etc.
Drive smoothly and keep a lookout
ahead
Vehicles use the most fuel when they are ac
celerating.
Avoid unnecessary accelerat ing and braking .
Vehicles use the most fuel when they are ac
ce lerat ing . If you anticipate what is going to
happe n next, you will need to brake less and,
th us, accele rate less. Let the vehicle coast
whenever possible -for examp le when you see
that the next t raff ic light is red.
Avoid full throttle
Driving at moderate speeds saves fuel and
improves your mileage.
"' Try and keep well below your car's maxi -
mum speed.
Acce lerat ing gently reduces fue l consump
tion, eng ine wear, and does not disturb the
environment.
Fuel consumpt ion, exhaust emiss ions and en
gine noise increase disproportionately at high
speeds. If you drive at approximately three
quarte rs of top speed, fuel consumption w il l
be reduced by one half. Never drive faster
t h an the posted speed limit and weathe r con
ditions perm it.
•
•
Automatic car wash
The vehicle can be washed in almost any
modern automatic car wash .
The vehicle paint is so durable that the vehicle
can normally be washed without problems in
an automatic car wash. However, the effect on
the paint depends to a large extent on the de
sig n of the fac ility, the filtering of the wash
water, the type of wash and care mater ial , etc.
If the paint has a dull appearance afte r go ing
through the car wash or is scratched, bring
this to the attention of the operator immedi
ately. If necessary, use a different car wash.
Before going through a ca r wash, be s ure to
take the usual precautions such as closing the
windows. Remove antenna if applicable .
If you have installed additional accessories on
the vehicle -such as spoilers, e tc. -it is best to
ask the car wash operator i f these should be
removed .
A WARNING
Always read and heed all WARNINGS and
the information ¢
page 164.
(D Note
- Fold the exterior mirrors -flat the re is a
risk of damaging the exterio r mirrors .
Power folding exterior mi rrors must not
be fo lded in or out by hand. Use the pow
er function!
- Compare the track of your vehicle w ith
the d istance between the guide ra ils of
the facility- there is a risk of damage to
the wheels and tires .
- Compare the width of your vehicle wit h
the width of the tu nnel at the fac ility.
Washing the vehicle by hand
A lot of water is needed when washing a vehi
cle by hand.
~ Befo re you start washing, make sure you
have read and understood the WARNINGS
¢ A in General informa tion on page 164 .
Cleaning and protec tion 165
~ First soak all dried d irt unt il it is soft, then
rinse it off.
~ As you clean yo ur vehicle, start w it h the
roof and work your way down to the bottom,
using a sponge, a sponge g love or a clean
brush .
~ Rinse the sponge o r the sponge glove often,
flushi ng it clean each time.
~ Use spec ia l car shampoo only fo r very per
sisten t dirt.
~ Rinse the car thoroughly wit h water.
~ Use a chamois leather to gent ly wipe the ex -
terior dry .
U se a separate sponge for cleaning the
whee ls, door s ills and other regions exposed
to road dirt. In this way, yo u wi ll not scratch
the paint wit h coarse particles imbedded in
the sponge the next time you wash the car.
A WARNING
- Wash your vehicle only when the ignition
is switched off to reduce the risk of a
crash .
- Always read and heed all WARNINGS and
other information ¢
page 164.
(D Note
-Never try to remove dirt, mud or dust if
the surface of the veh icle is dry. Never
use a dry cloth or sponge, s ince this
cou ld scratch your vehicle's paint or win
dows .
- Never wash your car in bright sun light.
Drops of wate r act as mag nifying lenses
and may damage yo ur paint .
- Whe n you wash your car in the winter: if
you rinse yo ur vehicle with a hose, be
c ar efu l not to aim the stream of water
directly at locks, or at doo r or hatch
openi ngs -they can free ze sh ut.
- Never use sponges designed to
remove
insec ts, or any k itche n sco uring sponges
or s imil ar p rod ucts. They can damage
your paint finish .
- Never use a dry cloth or sponge to clean
the headlights . Only use wet cloths o r
•
•
Rinse the vehicle thoroughly with water. Clean
the vehicle starting at the top and working to
ward the bottom using a
ne utral shampoo
and a soft m ic ro fi ber cloth . Stop frequently to
rinse the cloth thoroughly.
Clean the wheels and sill panels last. Use a
clean
s p on ge on these areas .
Rinse the vehicle tho roughly aga in and let it
air dry . If there are any water spots, they can
be removed using a
le athe r cloth.
Clean aga in with the s peci al cl ean er for matt e
fini sh p aint
if necessary.
R emoving stubborn dirt
B ird d ropping s or tree sap
are best removed
with p lenty of water and a m icrofiber cloth .
You should r inse
off ga soline residue immedi
ately with plenty of water .
A WARNING
-Wash your veh icle only when the ignition
is switched
off to reduce the risk of a
c rash .
- Always read and heed all WARNINGS and
othe r information
r=;> page 164.
(D Note
-Do not treat vehicle parts painted w ith
matte finish paint using polish ing mate
r ials or hard wax. These products could
cause damage to the appea rance or sur
face that cannot be repaired.
- Never use protective wax.
It can destroy
the matte fin is h effect.
- Do not p lace any st ickers or magnetic
s igns on vehicle parts painted w ith
ma tte finish paint. The pa int co uld be
damaged when the stickers or magnets
are removed .
- To prevent pa int damage, do not wash
the veh icle in direct sunl igh t.
- To prevent damage to the paint su rface,
do no t use insect removal sponges,
r o ugh kitchen sponges or similar items.
- You should remove debris (such as in
sects) from the headl igh t lenses on a
Cleaning and protec tion 167
regu lar bas is, for example when re fuel
ing your vehicle . Only clean the head
lights using a wet cloth or sponge, never
a dry one. Cleaning with soapy water is
recommended.
(D Tips
For more information on special clean ing
products designed for matte f inish paint,
see your Aud i dea ler.
Waxing and Polishing
Wa xing
A good wax coating pro tects the vehicle paint
to a large extent against the environmental
factors listed under
r=;> page 164, Washing and
even against s light scratches.
You can use a liquid car wax to protect your paint as soon as one week after your vehicle
has been delivered.
Even if you regularly use a
wa xing process in
automa tic car washes, we recommend that
you manually apply a coat of wax to g ive the
paint extra protection, part icularly if water no
longer beads on the clean paint .
Protect plastic body parts with car wax in the
same way as the veh icle body .
D uring warm weather dead insects tend to
collect on the front bumper and on the for
ward area of the hood. They are much easier
to remove from pa int that is waxed
often .
Polishing
Polish your vehicle only if the paint has lost its
shine and the g loss cannot be brought back
with wax.
If the polis h used does not contain p reserva
tive compounds, the paint must be waxed af
terwards.
A WARNING
-Always read and heed all WARNINGS and
other information
¢ page 164 .
•
•
you have the engine washed, the anti-corrosion treatment is a lmost always removed as
wel l. It is therefore essential to have a long
lasting corrosion protection reapplied to all
surfaces, seams, joints and components in the
engine compartment .
A WARNING
Be aware: The engine compartment of any
motor vehicle is a potentially hazardous
area.
- Before working in the engine compart
ment, be sure to read the informat ion
c::.>page 174.
- Before reaching into the front plenum
pane l, always remove the ignition key.
O therw ise, the windshield wipe r system
cou ld unintentiona lly be switched on,
poss ibly causing personal injury from the
moving wiper linkage .
- Never reach into the area around or
touch the radiator fan. The auxiliary fan
is temperature controlled and can switch
on suddenly- even when the ign it ion is
off.
- Do not wash, wax or dry the engine w ith
the engine running. Moving or hot parts could injure you .
- Do not clean the underside of the chas sis, fenders, wheel covers, or other hard
to reach parts w ithout protecting your
hands and arms. You may cut yourse lf on
sharp-edged metal parts .
- Always read and heed all WARNINGS and
other information
c::.> page 164.
Cleaning and protec tion 17 5
•
•
1 78 Fuel supply and filling your fuel t ank
transport fue l to use for your lawn mower,
snow blower, etc., be very careful and al
ways observe local and state laws regard
ing the use, transportat ion and storage of
such fuel containers . Make certain the con
tainer meets industry standards (A NSI/
AS TM F852 -86) .
(D Note
Never drive your vehicle unti l the fuel tank
is completely d ry. The irreg ular s upply of
fuel can cause misfir ing. Gasoline cou ld
e nte r into the exhaust system and damage
t he cata lytic conve rter.
Refuelling
Fi g. 12 9 Drive r's doo r: Un lo cki ng fuel f ille r flap
Fi g. 130 Fu el cap hooke d on the opened fuel filler flap
When adding fue l, the ignition and any ce llu
lar phones in the vehicle must be sw itched
off .
Tak ing the fuel cap off
• To open the fuel filler flap, pull the button
r:> fig. 129.
• Unscrew fuel filler cap counter-clockwise
and hang it o n the fuel filler flap ¢
fig. 130 .
Refuelling procedure
• Insert the f uel no zz le from the gasoline
pump into the fuel fi ller neck as far as it w ill
go .
• Select a med ium refuelling rate so that the
no zz le sw itches off automatically when the
tank i s full.
Putting the fuel cap back on
• After fi lling your tank, twist the fuel filler
cap clockw ise until you hear a definite click.
• Close the fue l filler flap.
T o avoid fuel s pill ing or evaporating from the
fuel tank always close fuel filler cap properly and completely . An improperly closed fuel fi ll
er cap may also cause the MIL lamp¢
page 30
to come on.
A WARNING
Imp roper refue ling or handling of fuel can
cause fire, explosion and severe burns.
- Fue l is highly flammable and can cause
severe burns and other injur ies .
- Fai lure to shut the engine off while refu
eling and/or to insert the pump nozzle
fu lly into the fuel filter neck could cause
fuel to spray out of filler neck or to ove r
f low. Fuel spray and overflowing fuel can
cause a fire.
- Never use a ce llu lar telephone whil e re
fue ling . Th e e lec tromagnet ic radiat io n
can cause spa rks th at can igni te fuel v a
pors an d cause a fire.
- N ever get back in to your vehicle whi le re
fue ling.
If in excep tio nal cir cumstances
you must get back in your vehi cle while
ref ueling, make ce rtain that you close
the door and touch metal to discharge
static electricity be fore touching the fill
er nozzle again . Static e lectr icity can
cause sparks that can ignite fuel vapors
re leased d uring refueling .
- Never smoke or have an open f lame any
where in or near your ve hicle when refu
eling or fi lling a portable fue l conta iner .