2013 AUDI TT ignition

16 Instrum ent s and w arn ing /indic ato r light s
_& WARNING
If you have a malfunction in the safety sys ­
tems, contact your authorized Audi dealer
immediate ly. Otherw ise the safety sys­
tems may not work properly in an acci­
dent.
~ Safety belt warning light
App lies to vehicles: with safety belt warning light
The warning light is a reminder to fasten
safety belts.
The warning light . comes on for a few sec ­
onds after the ignition is switched on as a re­
minder to fasten your safety be lt.
Addit ional info rmation on safety be lts
¢ page 100.
0 Generator
This warning/indicator light detects a mal­
function in the generator or in the vehicle's
electrical system .
The. warning/ind icator light illuminates
when yo u switch on the ignit ion and must go
out after the engine has started .
I f the . warning/indicator light illum inates
while you are driving, yo u should contact you r
author ized Audi dealer. Since the veh icle bat­
tery is discha rging, you should switch
off any
unnecessary electrical consumers (for exam ­
p le, the air conditioner).
~ Engine oil pressure
The red engine oil pressure warning symbol
requires immediate service or repair.
I f the . symbol appears in the display and
flashes, the oil pressure is too low . In addition
to the symbo l, the following message a lso ap­
pears in the d isp lay:
S wi tch off en gin e! Oil pr essure is t oo low
• Pull off the road and stop the vehicle .
• Shut the engine down.
• Check the eng ine oil level¢
page 185.
• Contact your authorized Audi dealer for as-
sistance if necessary .
Engine oil level too low
If the engine oil level is too low , top off oil to
t h e proper level
¢ page 185.
Engine oil leve l OK
If the . symbol starts flashing again even
though the eng ine oil level checks OK on the
dipstick,
do not start dri ving again and d o
not l et th e engine run at idl e.
Instead, con­
tact yo ur auth o rized Aud i dea ler fo r ass is­
tance .
(D Tips
- The engin e oil pr essure symbol. is
n ot an indi cato r for a l ow eng in e oil lev ­
e l. Do not rel y on i t. In ste ad, che ck th e
o il le vel in yo ur engine at regul ar inter­
vals, p referably ea ch time you refuel ,
a nd a lw ay s befo re going on a long t rip.
- The yellow oil le vel warning indication
Ill r equires oil refill or wor kshop s erv ­
ic e w ithout delay. Do not wait until the
red oil pressure warni ng sy mbol.
s tarts to flash before you re spo nd to
th e lo w oil level warning
111-By then,
y our engin e may already ha ve suffer ed
s er iou s damag e.
-L Engine cooling system
A malfunction in the engine cooling system
must be repaired as soon as possible .
When the. symbol in the d isplay flashes,
then either the engine coolant
temperature i s
too high, or the coolant
level is too low . In ad­
dition to the symbo l, the following message
also appears in the d isp lay:
Swit ch off en gin e and chec k coolant level
• Pull off the road and stop the veh icle.
• Turn
off the engine.
• Check coolant level
¢page 187.
• Add coolant if necessary¢ page 188.
• Continue driv ing on ly after the engine cool-
ant wa rning/ind icator light goes out. ..,.

Instrument s and warnin g/indic ator ligh ts 17
~ Contact your authorized Audi dea ler for as -
sistance if necessary.
If the engine coolant level is co rrect, then the
radiator fan may be the cause of the malfunc­
tion.
If the generator wa rning/ind icator light
should also illuminate
r:!:> page 16, then the
fan belt may be damaged.
A WARNING
- If your vehicle should break down for
mechanical or other reasons, park at a
safe distance from moving traffic, turn
off the engine and turn on the hazard
warning lights
c> page 45, Emergency
flasher &.
-
-Never open the hood if you see or hear
steam or coolant escap ing from the en­
gine compartment - you risk being scald­
ed . Wait until you can no longe r see or
hear steam or coo lant escaping.
- The engine compartment of any ve hicle
is a da ngerous a rea. Before you perfo rm
any wor k in the engine compartment,
turn off the engi ne and a llow i t to cool.
F ollow the wa rning stickers
¢ page 180.
(D Note
Do not co nti nu e d riving if the. symbol
illum inates. There is a ma lf u nct ion in the
eng ine cooling system -you co ul d damage
your eng ine.
@ Electro-mechanical power assist
If the indicator lig ht illuminates w hile you are
driving, there is a malfunction in the electro­
mechanical steering. If the ind icator light is
show ing ,£"~ . there may be a reduction in pow­
er steering assist. If the ind icator light is
show ing . , there may be a total loss of pow­
e r steering assist. The stee ring m ust be in­
spected immediately by a qua lified wor kshop
¢ ,&. .With the engine no t running (e.g. when
the car is being towed), there is a lso no power
assist avai lab le .
A WARNING
-
If there is a ma lf u nction, the indicator
light for the electro-mechanical power as­
sist illuminates. Seek professional assis­
tance.
~ Clutch pedal
App lies to vehicles: wit h manual transmiss ion
T he ind icator light [~l ill uminates if you do
not press the clu tch pedal when s ta rting the
engine. For safety reasons, the eng ine will on ­
ly start when the clutch peda l is pressed.
;;,I C; Electronic Stabilization Control
(ESC)
If the hJ indicator lamp blinks while dr iv ing,
the ESC or ASR (Anti-Slip Regu lation) is active ­
ly regulating .
If the
G! indicator lamp illuminates, the sys­
tem has switched the ESC off. In th is case, you
can switch the ignition off and then on to
switch the ESC on again. The system is func­
t ion ing complete ly when the ind icator lamp
swi tches off.
If the
I) indicator lamp illuminates, the ESC
was switched off w ith the
[ru button .
Stabilization program and AB S fault! See
owner 's manual
If the G! indicator lamp and the [I] ABS indi­
cator lamp illum inate and the driver message
appears, the ABS or electron ic different ia l lock
is malfunct io ning . This also interrupts the
ESC. The brakes still function with their nor ­
mal power, but ABS is not active.
Drive to your authori zed A udi dealer immedi­
ate ly to have the malfunction corrected .
For more information abo ut the ESC
¢ page 150.

18 Instruments and warning/indicator lights ABS/
{i§l) Anti-lock brake system
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL) .
The warning/indicator light & (USA mod­
els)
;tlJ (Canada models) will come on for a
few seconds when the ignition is switched on .
The l ight will go out after an automatic check
sequence is completed.
There is a malfunction in the ABS when:
-The warning/indicator light does not illumi­
nate when you switch the ign ition on .
- The warning/indicator light does not go out
after a few seconds .
- The warning/indicator light illuminates wh ile driving.
The ESC indicator light also illuminates if
there is a malfunction in the ABS . The mes­
sage
Stabilization program and ABS: fault!
See owner's manual
also appears in the in­
strument cluster display and a warning tone
sounds .
The brake system will still respond even
without the assistance of the ABS system.
See your authorized Audi dealer as soon as
possible to restore full braking performance.
For more informat ion regarding the ABS
¢ page 150.
Malfunction in the brake system
If the brake warning light¢ page 14 and the
ABS warning illuminate
together there may be
a malfunction in the ABS, and there may also
be a ma lfunction in the brake system itself
¢ ,&.. The ABS will not work and you will no­
tice a change in braking response and per­
formance.
In the event of a malfunction in the brake
system
t h e warn ing/ indicato r light 1111
(USA models) . (Canada models) in the in­
strument cluster flashes
9 page 14 .
Malfunction in the electronic differential
lock (EDL)
The EDL works together with the ABS. The
ABS warning light will come on if there is a malfunction in the
EDL system
¢page 150.
See your authorized Audi dealer as soon as
possible.
A WARNING
"---
- If the E (USA mode ls)l ii] (Canada
models) warning light does not go out,
or if it comes on whi le driving, the ABS
system is not work ing properly . The vehi­
cle can then be stopped only with the
standard brakes (without ABS). You w ill
not have the protection ABS provides.
Contact your Audi dea ler as soon as pos­
sible.
- USA models: If the 1111 warning ligh t,
the
J;.J warning light and the & warn­
ing light come on together, the rear
wheels could lock up first under hard
brak ing. Rear wheel lock-up can cause
loss of vehicle control and an accident.
Have your vehicle repaired immediately
by your authorized Audi dealer or a quali­
fied workshop. Dr ive slow ly and avoid
sudden, hard brake applications.
- Canada models: If the brake warning
light ., the
DJ warning light and the
ABS warning light
[( Gi a come on together,
the rear wheels could lock up first under
hard braking. Rear wheel lock-up can
cause loss of vehicle contro l and an acci­
dent . Have your vehicle repaired immedi­
ately by your authorized Audi dealer or a
qualified workshop. Drive s lowly and
avoid sudden, hard brake applications.
{0) Worn brake pads
EtJ Check brake pads!
If the warning light i lluminates, immediate ly
contact your authori zed Audi dealer or quali­
fied workshop to have all brake pads inspect­
ed . On USA models the warn ing light
EtJ
comes on together with the warning light
1111. Both sets of brake pads on an ax le
must always be replaced at the same time.

Instrument s and warnin g/indic ator ligh ts 19
A WARNING ,~ ~
Driv ing with bad brakes can cause a coll i­
sion and serious personal injury .
- If the warning light
liJ and the warning
light
11111> w ith the message Brak e
pad s!
comes on in the instrument cluster
display, immediately contact your au­
tho rized Aud i dealer or qualified work­
shop to have a ll brake pads chec ked or
replaced if necessary.
EPC Electronic power control
This warning/indicator light monitors the
electronic power control.
The ~ warn ing/ indicator light (Electron ic
Power Control) illuminates when you switch
on the ignition as a function check .
(D Tips
If this warning/indicator light illuminates
while you are dr iving, then there is a mal­
function in the engine elect ron ics. Have
t he malfunction co rrected as soon as pos­
sible by you r autho rized Aud i dea ler o r
qualif ied workshop .
~ Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) is part
of the On-Board Diagnostic (OBD II) system.
The symbol
l\l lights up when the ignition is
turned on and will turn off after the engine
h as started and has settled at constant idle
speed . Th is ind icates that the MIL is working
properly .
The warning light illuminates when there is a
malfunct ion i n the engine electronic system.
Contact your author ized Audi dealer and have
the ma lfunction corrected.
An imp roperl y closed fuel filler cap ma y also
c au se th e MIL light to illum inat e
<:::>page 178.
For more informat ion c:::> page 30.
1) - : USA mod els only
!'1 Engine speed limitation
App lies to veh icles: w ith eng ine speed limitatio n
(II Do not exc eed max . engin e speed of
XXXX rpm
The Ill symbol illum inates when there is an
engine contro l ma lf u nction . The indicator
li ght ~ in the instrume nt cl uster a lso illumi­
na tes. The engi ne speed is l imited to the
speed displayed in the driver in format ion sys­
tem. Keep in mind that the engine speed wi ll
not exceed the val ue disp layed in the driver in­
format ion system, for example when down­
shifting.
P lease go to an au thorized A udi dealer or oth ­
er qualified wo rkshop to have the malfunctio n
repaired.
'.!2::. Checking the engine oil level
II Please add ma x. 1 qt of engine oil!
If the II symbo l comes on, add 1 quart ( 1 li­
ter) of oil at the next opportunity
<=>page 185.
~~. Engine oil sensor defective
If the II symbol illum inates, contact your
authorized Aud i dea ler and have the oil sensor
inspected .
0 Battery voltage low
(•) Low battery charge : battery will be
c harg ed whil e driving
If the indicator l ight turns on and the mes­
sage appears, there may be limited starting
ability.
If this message turns off afte r a little while,
the battery charged enough while d rivi ng .
If the message does not turn off, have yo ur
authorized Aud i dea ler or qualified workshop
correct the malfunction .

Instrument s and warnin g/indic ator ligh ts 21
@:> Light/rain sensor defective
Applies to vehicles: with a utomat ic head lights
The indicator light indicates a defect in the
automatic headlights/automatic wiper sys­
tem .
If the symbol illuminates, the light sensor has
failed . For safety reasons, the low beams are
turned on permanently with the switch in
A U­
TO . However , you can continue to turn the
lights on and off using the light switch . In the
case of a defect in the rain sensor, the w ind­
shie ld wiper lever functions are sti ll available.
Have the light/rain sensor checked as soon as
possible at an authorized Audi dealer.
; Audi magnetic ride
App lies to vehicles: with Audi magnetic ride
The indicator light monitors vehicle damping .
The indicato r light B illum inates when the ig­
n it ion is switched o n as a funct ion check.
(j) Tips
If the ind icator lamp illum inates while you
are driving, there is a malfunct ion in the
veh icle damping. The chass is should be in­
spected immediately by an authorized
Audi dea ler .
:::/, Rear spoiler
The warning/indicator light monitors the
electrically retractable rear spoiler.
The warning/indicator light l'J has the fol­
l owing f un ctions:
- It comes on for about 3 seconds as a func­
t ion check when the ignition is sw itched on .
- It comes on if there is a malfunction in the
electrically retractable rear spoiler .
Addit ional information about the electrically
retractable rear spo iler
¢ page 153.
¢ Q Turn signals
The indicator light blinks when you use either
turn signal .
Whenever you use the left II or the r ight II
turn s ignal, the indica tor light blinks. When
you use the emergency flasher, both indicator lights flash .
If one of the turn signa l light bulbs burn out,
the turn signal will blink twice as fast as nor­
mal.
Additional informat ion on the turn signals
¢ page 44.
CRUISE/ 0" Cruise control
The tB;(l)~i# (USA models)/ . (Canada models)
warning/indicator light illuminates when the
cruise control is act ivated .

24 Driver information system
the calculation of the current trip informa­
t ion. If the trip is interrupted for
more than 2
hours
the memory is reset automatica lly.
Total -trip memory (Trip computer 2)
Unlike the sing le-trip memory, the total-trip
memory is not reset automatically. This per­
mits you to evaluate your dr iving data for the
entire period between manual resets.
Efficiency program*
The effic ien cy program can help you to use
less fuel ~
page 26.
Operation
The trip computer is controlled by two
switches on the windshield wiper lever.
-----------< @
Fig. 10 W iper arm/w iper lever: con tro ls for t he trip
compute r
Selecting the trip computer
" Tap the I Reset I button @ until the trip com ­
puter (memory level 1 or 2) appears in the
display ¢
page 23, fig . 8 .
Selecting the functions
" Push in the upper ( lower) protrusion on the
function selector switch @
q fig. 10. The
functions for the trip computer are d is ­
played in succession on the respective mem­
ory levels.
Resetting the function to zero
" Push the I Reset ! button ® for at least two
seconds.
You can reset the fo llowing values to zero us­
ing the
I Reset I button :
- driving time - distance
-
average f uel mileage
- average speed
The t rip computer only operates when the ig­
nition is on. When you turn on the ignition,
the function that was in use when you last
turned the ignition off will be displayed .
(D Tips
-You can also set the values for the func­
tions to zero in the menu display
(Reset )
qpage24 .
-All stored values will be lost if the vehi­
cle battery is disconnected .
- The driving information in the efficiency
program is a lso reset to zero w ith the
single-trip memory.
Menu display
Introduction
Display Type
•set
iF'Cf t -,,., ==
Menu off
Fig. 11 D isplay: Sta rt men u
Some funct ions in yo ur vehicle can be set , ac­
t ivated, and controlled by
Menus (e.g. Acous­
tic park assist *). With these menus you can al­
so select the information shown in the driver
information system, which operates only with
the ignition switched on. Operation is control­
led by the
! Reset I button and the rocker switch
on the wiper lever
q page 25, fig . 12.
The Start menu shows you the different dis­
play types:
Set
Check
Menu off

26 Drive r information system
-I
10
Box Not selected
~
Triangle point- Previous page
ing up
Triangle point- Next page ing down
Selecting settings
Th e Driver Information System settings are
menu-guided.
Fig. 14 Display: Menu Settings, computer selected
(page 1)
Select your settings as follows:
,.. Press the !Reset
I button . The Start menu
appears¢
page 24, fig . 11.
,.. Press the rocke r switch until Set is d is­
played .
,.. Press the
I Reset I button. All the menus ap­
pear.
,.. Press the rocker switch until the desired line
is highlighted (cursor)¢
fig. 14.
,.. Press the !Resetl button.
,.. If necessary, scroll by selecting and activat­
ing the symbol for "Next page" or "Previous
page" .
When you have selected the Computer menu
and activated it by pressing the
I Reset ! but ­
ton, two computer levels appear (computer 1
and computer 2). Now you have to select the
level you want using the rocker switch and ac­
tivate it w ith the
I Reset I button .
Engine oil temperature
display
Applies to veh icles: w it h eng ine temperature control d is ­
play
• Engine oil
Temperature
176 °F
•Back
Fig. 15 Display: eng ine o il temperature d isp lay
,.. With the ignition switched on, press the
N a, !!? ti. m m
I RESET I button ¢ page 24, fig . 10 repeated­
ly until the engine oil temperature disp lay is
shown.
T he engine has reached its operating temper­
ature when the engine oil temperature is be­
tween
176 Of (80 °() and 248 O f (120 °() U n·
der normal driving conditions. The engine o il
temperature may be higher if there is heavy
engine load and high temperatures outside.
This is not a cause for concern as long as the
• ¢page 16 orlll c=> page 19 warning light
in the display does not flash .
Efficiency program
Description
Applies to vehicles: w ith trip computer with eff iciency
p rogram
..
lJI 300m,
27.7 mpg
25.8 m1>g
Fig. 16 Dis play: efficiency program
,.. Press the I RESET ! button @ c:> page 24,
fig . 10
repeatedly until the efficiency pro­
gram appears in the display.

28 Driver information system
Service interval display
The service interval display reminds you when
your next service is due.
Fig. 19 Sect ion of instrument cluster: Serv ice inte rva l
d isplay
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed
accordingly. The display works in two stages :
Service reminder
30 days before the next service is due, a serv­
ice reminder appears in the display when you
turn on the ignition.
After about
S seconds the display switches
back to normal. The distance and time re­
maining are updated each time the ignition is
turned on until the date due for service is reached .
Service due
When the due date for service is reached , the
message
Service due! appears in the instru­
ment cluster immediately after you turn on
the ignition. Additionally, a warning tone
sounds . After about
S seconds the display
switches back to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the instrument cluster by se­
lecting the service interval display. Select
Check > Service > Oil change or Service by us­
ing the
! RESET I button and the rocker switch
c;, page25, fig.12.
Resetting the service interval display
Your authorized Audi dealer will reset the cor­
responding service schedule after performing the appropr
iate service on your vehicle. You
also have the possibility to reset the oil
change schedule after hav ing performed an
oil change according to Aud i specifications.
- Switch the ignition on.
- Pull the knob¢ fig. 19. The message.
Serv-
ice due!
appears.
- Pull the knob until the display
Oil change in
----- mi (km)·-- days
appears. If the I RESET I
button is not pulled within 5 seconds, the
disp lay reset mode closes.
(D Note
If yo u disconnect the battery terminals, no
ca lculations can be made for the service
interval display during this time and no
service reminder will appear. Remember
that observing the proper service intervals
is vitally important to extending the life of
your vehicle, particularly the engine, and maintaining its value . Even if the mileage
driven is low, the maximum period of one
year from one service to the next must not
be exceeded.
(D Tips
-Do not reset the display between oil
changes, otherwise the display will be in­
correct.
- The information in the Service Reminder
remains stored even when the vehicle
bat tery is disconnec ted.
Boost and engine oil
temperature indicator
Appl ies to vehicles: wit h boost pressure indicato r
0 ~ 00 0
j IX)
Fig. 20 D isplay : boost and engine oi l temperature indi·
a~r ~