2013 AUDI S8 brake

CD Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift ­
ing points on the sill. Otherwise , your vehi­
cle will be damaged.
(D Tips
The vehicle jack mode switches off auto ­
matically at speeds above 10 km/h .
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fig. 222 C h ang ing a w hee l: u sing t he sc rew drive r han ­
d le (w it h th e blade remov ed) to tu rn th e bolt s
Fig. 223 C h ang ing a w hee l: alig nme nt pin inside the
top hole
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal socket in the screwd riv­
er handle
to completely remove the top­
most wheel bol t and set it aside on a
clean
surface ¢ fig. 222 .
What do I do now? 27 7
.. Sc rew the threaded end o f the alignment
pin
from the tool kit hand-tight into the
empty bolt hole
¢ fig. 223 .
.. Then remove the other wheel bolts as de­
scribed above.
.. Take off the wheel leaving the alignment
pin in the bolt hole
¢(D .
Putting on the spare wheel
.. Lift the spare wheel and carefully slide it
over the alignment p in to guide it in place
¢ (]).
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
.,. Remove the a lignment pin and insert and
tighten the rema ining wheel bolt slightly
like the rest .
.. Turn the jack hand le counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
.. Use the wheel bolt wrench to tighten all
wheel bolts f irmly
¢ page 2 75. Tighten
them
crosswise, from one bolt to the (ap ­
proximately) opposite one, to keep the
wheel cente red.
CD Note
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you.
@ Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or tighten
the wheel bolts.
- Pull the reversible blade from the screw­
driver before you use the hexagonal
socket in the hand le to turn the wheel
bolts.
- When mount ing tires with
unidirectional
tread design
make sure the tread pat­
tern is pointed the right way
¢page 278.
- The wheel bolts shou ld be clean and easy
to turn. Check for dirt and corrosion on
the mating surfaces of both the wheel

280 Fuses and bulbs
Fuse panel @ (brown)
No. Equipment
1 Headlight control switch
2 Emergency start coil (key
identification)
3 Rear door
control module
(driver's side)
5 Horn
6 Interior lights
(headliner)
Steering column lever, mul-
8
tifunction steering wheel
controls, steering wheel
I heating
10 Power steering column ad-
justment
11 Driver door control module
12 Diagnost
ic connector, light/
rain sensor
14 Power steering column ad-
justment
15 Power
steering, A/C com-
pressor
16 Brake booster
Fuse panel © (black)
No. Equipment
1 Front seat heating
2 Windshield wiper
3 Front exterior lighting
4 Sun roof
5 Driver power window
6 Driver seat (pneumatic)
7 Panoramic
sunroof
8 Dynamic steering
9 Front exterior lighting
10 Windshield/headlight
wash-
er system
11 Rear power window (driver's
side)
Panoramic sunroof
Amps
5
5
7,5 15
7,5
10/5
5
7,5 10
25
20 15
Amps
30
30
30 20
30
7,5
20
35
30
35
30
40
Front passenger side cockpit fuse
assignment
Fig. 227 Front passe nger side cockpit: fuse pane l with
plastic bracket
Fuse panel ® (black)
No. Equipment Amps
1 Anti-theft alarm system
5
2 T
ransmission control mod-
15
ule
3 Front climate control fan 40
4 Engine supply 35
6 Engine
control module
5
7 Front passenger door con-
7,5
trol module
8 Front passenger
power win-
30
dow
9 ESC control module 10
10 E5C control modu le 25
11 Right rear power window
30
12 Front passenger
seat (pneu-
7,5
matics)

Fuse s and bulb s 281
Luggage compartment fuse assignment
Fig. 228 Luggage compartment: fuse pa nel with plastic bracket
Fuse panel @ (black ) Fuse panel @ (b la ck)
No . Equi pment Amps No. Equipment Amps
[ru button, data logger, diag-
11 Dynamic
steering
5
l nostic
connector, BCM -1,
5
Selector lever, BCM-2 5
adaptive light ing system
Audi side assist
5
2 Networking gateway 5
Engine control module 5
3 adaptive air suspension
5
Starter 40
4 Parking system 5
Left headlight/Headlight
16 10/5
5 Steer
ing column lever
5
range control system
6 Suspension control system
5 Fuse panel
@ (red ) sensor
Belt tensioners, airbag con-
No. Equipment Amps
7 trol module 5
l Left
reversible be lt tens ione r 25
Heated washer fluid nozzles, 2
Right reversible belt ten-
25
Homelink (garage door sioner
8 opener), night vision system 5 Starter diagnos
is, DC/DC
control module, sport differ-3 c onverter (Start-Stop-Sys-5
ential, ioni zer tern )
9
Electromechan ica l parking
5 4 DC/DC converter 7,5
brake contro l modu le 5 Image pro cessing 7 ,5 -
10
Rear seat heating, cooler, in-
5
terior rearview mirror

282 Fuses and bulb s
Fuse panel
® (red)
No. Equipment
=
I 6
Right headlight (headlight
with adaptive light)
7 ESC control module
8
Sound actuator, AEM control module
9 Adaptive cruise control
10 Transmission control mod
-
ule
11 Climate control system sen-
sors
Fuse panel © (brown)
No. Equipment
1
Electromechanical parking
brake
2 Suspension control system
sensor
3
Right rear door control mod-
ule
Smart modul tank
5
Front cl imate control system
contro ls
6
Rear climate control system
controls
7 Networking gateway
8 Cooler
9
Interface for specia l func-
tions
10 Cell phone adapter, Blue-
tooth handset
11 AEM contro
l module
12
13 Ambient
lighting
14 Rear exterior lighting
15 Fuel pump
I 16 Electromechanical parking
brake
Amps
=
10
5
7,5
10
5
5
5
5
7,5
5
15
10
5
15
5
5
15
10
10
20
25
30
-
Fuse panel @ (black)
No. Equipment
1
3
5
6
7
Automatic luggage com­ partment lid
Rear sockets
adaptive air suspens ion
115-V socket
Electromechanical parking
brake
8 Rear seat heating
9 Rear exterior lighting
10 Rear climate control system
blower
Rear sun shade, closing aid,
11 luggage compartment lock,
keyless go/entry, fuel filler
door
12 Luggage
compartment lid
control module
Fuse panel E (red)
No. Equipment
1 Rear seat adjustment but-
tons
3 Left rear seat (pneumatics)
5 Tra iler hitch control modu le*
6 Left rear seat
7 Right rear seat
8 Trailer hitch control module*
9 Trai ler hitch control modu le*
10 Right rear seat (pneumatics)
Fuse panel
® (brown)
No. Equipment
1 Start-Stop-System,
Radio re-
ceiver/sound amplifier
Sound amplifier
Start-Stop-System, Rear
3 Seat Entertainment, radio
receiver/sound amplifier
5 Automatic dimming interior
rearview mirror
6 DVD changer
Amps
5
20
15
25
30
25
20
20
20
30
Amps
5
7,5 20
30
30
20 15
7,5
Amps
30
30
10
5
5

@ Tips
- The discharged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump start ing or charging the
battery, never connect the negative
ground cable to the battery negative post because the battery manager sys­
tem must be able to detect the battery's
state of cha rge. A lways connect the neg­
ative g round cab le to the negative
gro und post o f the battery manage r con­
trol uni t.
Use of jumper cables
Make sure to connect the jumper coble
clomps in exactly the order described below!
Fig. 229 Engine compartment: connecto rs for jump
start cables and charger
Fi g. 230 Jump start ing w ith the battery of another ve ­
hicle: @-booste r batte ry, @ -discharged vehicle bat ­
te ry
The procedure described below fo r connecting
jumper cab les is intended to provide a jump
start for your veh icle.
Vehicle with discharged batt ery:
.. Turn off lights and acc esso ries, move leve r
of automat ic t ransm ission to N (Neutral) o r
P (Park) and set pa rking brake .
Emergenc y situ ation s 285
Connect POSI TIVE(+) to POSITIVE (+ )
(red )
.. Open the red cover on the positive terminal
¢fig. 229.
1. Connect one end of the red positive cable
on the
jump sta rt bolt ¢ fig. 230 (D (bolt
under the red cover = "positive") of the ve­
hicle to be started @.
2. Co nnect th e other end to the pos itive ter-
mina l@ of the booster battery @.
Connect NEGATIVE( -) to NEGATIVE(-)
(black )
3. Connect one end of the black negative ca­ ble to the negat ive termina l@ of the
booster b attery @.
4 . Connect the othe r end to the
jump start
pin @ (bolts with hex head bolt = "nega­
tive") of the vehicle to be started @.
Starting the engine .. Sta rt the engine of the veh icle w ith the
booste r ba ttery @. Ru n the engine at a
moderate speed .
.. Start engine wit h discha rged vehicle battery
@ in the usual manner .
.. If the eng ine fails to start, do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 seco nds a nd the n try
aga in .
.. With engi ne runni ng, remove j umper cab les
from both vehicles in the exact
reverse o r­
de r .
.. Close the red cover on the positive term inal.
T he battery is vented to th e outside to p rev ent
gases from en ter ing the veh icle in ter io r. Ma ke
s ur e th at the j umper clamps are well connec t­
ed with their meta l parts in full con ta ct w ith
the battery term inals.
A WARNING
To avoid se rious personal injury and dam­
age to the veh icle, heed all warnings and
instructions of the jumper cable man ufac­
turer. If in doubt, call for road service .
- J umper cables m ust be long enough so
that the veh icles d o not touch.
-

286 Emergency situations
-When connecting jumper cables, make
sure that they cannot get caught in any
moving parts in the engine compar t­
ment .
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c:> page 226 , Engine com­
partment.
(D Note
Improper hook-up of jumper cables can ru­
in the generator.
- Always connect POSITIVE(+) to POSI­
TIVE( +), and NEGATIVE( -) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that all screw plugs on the battery
cells are screwed in firmly . If not, tighten
plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
necting a jumper cable as described
above applies specifically to the case of
your vehicle being jump started. When
you are giving a jump start to another ve­
hicle, do
not connect the negative(-) ca­
ble to the negative(-) terminal on the
discharged battery ©
c:> fig. 230. In­
stead, securely connect the negative(-)
cable to either a solid metal component
that is firmly bolted to the engine block
or to the engine block itself . If the bat­
tery that is being charged does not vent
to the outside, escaping battery gas
could ignite and explode!
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
tng.
The following information is to be used by
commercial tow truck operators who know
how to operate their equipment safely.
-Never tow your Audi. Towing will cause
damage to the engine and transmission.
- Never wrap the safety chains or winch ca­
bles around the brake lines.
- To prevent unnecessary damage, your Audi
must be transported with a flat bed truck.
- To load the vehicle on to the flat bed, use
the towing loop found in the vehicle tools
and attach to the front or rear anchorage
c:> pag e 286 and c:> page 287.
.&_ WARNING
=
A vehicle being towed is not safe for pas-
sengers. Never allow anyone to ride in a
vehicle being towed, for any reason.
Front towing loop
Only install the front towing loop when it is
needed .
C7
0
Fig. 231 Front bumper: cover
Fig. 232 Front bumper : sc rewing in th e towin g loop
-
The towing loop fits into the threaded hole lo ­
cated on the right side of the front bumper
and covered by a small cover when not in use.
.,. Remove the towing loop from the veh icle
tool kit.

298 Consum er Inf ormation
-Always make sure the transmission se­
lector lever (automatic transmiss ion) is
in "P" (Park position) and the park brake
is applied .
@) For the sake of the environment
-Changing the engine settings wi ll ad­
versely affect em iss ion levels. This is det­
rimental to the environment and increas­
es fuel consumption .
- Always observe env ironmental regula­
tions when dispos ing of old engine oil,
used brake fluid, dirty engine coolant,
spent batteries or worn out tires.
- Undeployed airbag modules and preten­
s ioners might be classified as Perchlo ­
rate Material -spec ial handling may ap­
ply, see www.dtsc.ca .gov/hazardous­
waste/perch lorate . When the veh icle or
parts of the restraint system including
airbag modules safety belts with p reten ­
sioners are scrapped, all applicable laws
and regulations must be observed. Your
authori zed Aud i dea ler is familiar with
these requirements and we recommend
that you have your dealer perform this
serv ice for you .
Additional accessories,
modifications and
parts replacement
Additional accessories and parts
replacement
Always consult an authorized Audi dealer be­
fore purchasing accessories.
Your veh icle incorporates the latest safety de­
sig n featu res ensu ring a high standard of ac­
tive and passive safety .
This safety could be compromised by non-ap­ proved changes to the veh icle. For this reason ,
if pa rts have to be replaced , please observe
the following points when install ing addition­
a l accessories: Approved Audi accessories and genuine Audi
parts are available from authorized A udi deal­
ers.
T hese dea le rs a lso have the necessary facili­
ties, tools and trained specialists to install the parts and acc essories proper ly .
A WARNING
-Using the wrong spare parts or using non-
approved accessories can cause damage to
the veh icle and ser ious persona l injury.
- Use on ly accessories express ly approved
by Audi and gen uine Audi spare parts
- These parts and accessories have been
specia lly designed to be used on yo ur ve­
h icle .
- Never install accessor ies such as tele­
phone crad les or beverage ho lders on a ir­
bag covers or within the airbag deploy­
ment zones . Do ing so will increase the
risk of injury if a irbags are triggered in an
accident!
- Before you check anything in the engine
compa rtment, always read and heed a ll
WARNI NGS
9 page 226 .
(D Note
-If items other than genu ine Audi spare
parts, add-on equipment and accessory
items are used or if repair work is not
performed accord ing to specified meth­
ods, this c an resu lt in seve re damage to
your vehicle's eng ine and body (such as
corrosion) and adversely affect yo ur vehi ­
cle's warranty .
- T he i nnovat ive a luminium concept of
your Audi AB means that all servicing, re­
pairs or other work on the vehicle body
must be carr ied out exclusive ly by an
Audi workshop .
- If emergency repairs must be performed
elsewhere, have the veh icle examined by
an authorized Audi dealer as soon as
possible .
- The manufacturer cannot be held liable
for damage wh ic h occurs due to failure
to comply with these stipu lations .

302 Index
Automatic transmission (tiptronic) .... . 115
Emergency mode . ..... ... .. .. .... . 11 9
Kick-down . .... ... .... ... .. .. .... . 118
Manual shifting . . . . . . . . . . . . . . . . . . . 118
Park ing lock emergency release ..... . 120
Selector leve r posit ions . . . . . . . . . . . . . 115
Automatic wipers . . . . . . . . . . . . . . . . . . . . 52
Auto Safety Hotline ...... .. .. .. .. .. . 142
Average consumption ................. 24
Average speed . . . . . . . . . . . . . . . . . . . . . . . 24
Avoid damaging the vehicle . ... .. .. .. . 207
B
Ba ttery . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
C harging ... ................ ... ... 246
Important warnings ...... .. .. .. .. . 244
L ocat ion . . . . . . . . . . . . . . . . . . . . . . . . . 244
low . .. .. .. ............. .. .. .. .. . 203
Replacing the battery ..... .. .. .. .. . 247
State of charge . .. ..... ... .. .. .... . 203
Winter operation . ..... ... .. .. .... . 243
Wo rking on the battery . . . . . . . . . . . . . 244
B efore d riving .. ........... .... .... . 134
Blended gasoline ............ .. .... . 228
Blower (automatic climate cont rol) . . . . . . 80
Body cav ity sealing .......... .... .... 221
Booster seats ...................... 184
B rake fl uid
Changing the brake fl uid ... .. .. .. .. . 243
Checking the brake fluid level ..... .. . 242
What is the correct brake fluid leve l? .. 242
What should I do if the brake fluid warn-
ing light comes on? ................ 242
Brake system Anti-lock braking system ... .. .. .. ... . 1 9
Brake assist system .. ... .. .. .... .. . 198
Brake booste r .. .......... .. .. .... . 202
Brake fluid .............. .. .. .. .. . 242
Brake fluid spec ificat ions for refill and re­
placement . . . . . . . . . . . . . . . . . . . . . . . 243
Brake light defect ive ....... .... ..... 21
Brake pads . ........ ......... .... . 206
E lec tromechan ica l par king brake ...... 85
Fl uid reservoir ........... .. .. .. .. . 242
H ow does mo isture or road salt affect the
b rakes? .... ... .. ..... ... .. .. .... . 200 Warning/ind
icator lights ..... .... . .. . 14
Worn brake pads symbol . . . . . . . . . . . . . 20
braking guard Messages . .. .. .. ............. .. .. 100
Brak ing guard . .. .. .......... ...... .. 93
Settings ......... ............... . 100
Break-in period .... .. ... ..... ... .. .. 206
Brake pads .... .. ............. .... 206
Tires . .. .. .. .. .. ............. .. .. 206
Bu lbs . ... .. .... .. ... .. ..... .... . .. 283
C
Californ ia Pr oposition 65 Warn ing . .... 233
Battery spe cific .. ... .......... .. .. 24S
Capacities ........ .. .............. . 292
Engine o il ... .. .. .. ... ....... ... .. 23S
Car care .. .. .. .. .. ............. .. .. 215
Exterior ....... .. .. ........... .... 215
Interior ....... ................... 222
Car carrier Transporting your vehicle .... ... .. .. 288
Cargo a rea
refer to L uggage compartmen t ... .. . .
Catalytic converter
Center armrest 140
207
Cockpit ... .... .. .. ... .. ... ... .. .. . 60
Rear . .... .... .. ............. .... . 67
Cen tral lock ing ...................... 32
E mergency lock ing . .. .. ..... ... .. .. . 36
Certif ication .. .. .................. . 299
Changi ng a wheel .. .. .... .... ... .. .. 273
Changi ng engine oil ............. .... 239
Chassis (undercoat ing) .............. . 221
Checking Engine coolant level .. .. ..... .... . .. 240
Tire pressure . .. .. ............. .. .. 255
Child rest raints
Danger of using child restraints in the
front seat ..... .. .. ... ..... ... .. .. 154
Where can I get additional information
about child restraints and their use? .. 195
Child rest raint system anchors ........ 189
Child safety ... .. .. .. ... ....... ... .. 176
Convertible locking retractor ........ . 186
Gu idance fixtures for lower anchorages 191