2013 AUDI RS5 CABRIOLET ESP

functions will be available again when you
switch on the ignition and start the engine.
With the engine turned off
If you listen to the radio, for example, with
the eng ine turned off or use othe r MM I fu nc­
tions, the battery is being discha rged.
I f starting capability is jeopardized due to en­
e rgy consumpt ion, the fo llow ing warning ap­
pears in the MMI disp lay :
Plea se start the eng ine soon or th e sys tem
w ill b e turn ed off .
The warning ind icates that the system will be
turned off automatically after 3 m inutes . If
you wish to cont inue us ing the functions , you
have to start the engine.
With the engine running
Although electrical energy is generated when
the vehicle is be ing driven, the battery can be­
come discharged . Th is happens mostly when
little energy is be ing generated and a great
deal consumed and the battery's state of
charge is no t optimal.
To br ing the energy balance back into equili ­
b rium, consumers which require especially
l arge amounts of energy are tempo rarily cut
back or swit ched off. Heating systems in par­
ticular requ ire a g reat dea l o f energy. If you
notice, fo r example, that the heated seats* or
the heated rear window are not heating, they have been temporari ly cut back or switched
off. These systems will be ava ilab le again as
soon as the energy balance has been restored.
You will a lso notice that engine idle speed has
been increased slightly . This is norma l and not
a cause for concern . By increasing engine idle
speed the add itiona l energy required is gener­
ated and the battery is charged.
Int ellig ent technolog y 183
•
•

184 Driving and environment
Driving and
environment
The first 1,000 miles
(1,500 km) and
afterwards
New engine
The engine needs to be run-in during the first
1,000 miles (1,500 km).
For the fir st 600 miles (1,000
kilometers ):
.,. Do not use full throttle.
... Do not d rive at engine speeds that are more
than 2/3 of the max imum permitted RPM.
From 600 to 1,000 miles (1 ,000 to
1,500 kilomete rs):
.,. Speeds can gradually be increased to the
max imum pe rm iss ible road or eng ine speed .
During and after break-in per iod
... Do not rev the eng ine up to high speeds
when it is cold. Th is app lies whether the
transmission is in N (Neutra l) or in gear.
After the break- in period
... Do not exceed max imum engine speed un­
der any circumstances .
... Upshift into the next higher gear before
reaching the red area at the end of the tach­
ometer scale¢ page 10.
During the first few hours of driving, the en­
g ine's inter na l friction is higher than later
when all the moving parts have been broken
i n. How well this break- in process is done de­
pends to a conside rable extent on the way the
ve hicl e is driven du ring the first 1,000 miles
(1, 500 kilome ters).
(D Note
E xtremely high engi ne speeds are auto­
mat ica lly r educed. However, t hese rpm
lim its are programme d for a n engine well
r u n- in, not a new eng ine.
{® For the sake of the environment
Do not drive with unnecessarily high en­
g ine speeds - upshifting ear ly saves fuel,
reduces no ise and protects the environ­
ment.
, New tires
If your vehicle is runni ng on new tires, drive
very carefully for the first 350 miles (500 kilo­ meters) after fitting.
_& WARNING
N ew tires tend to be slip pery a nd mus t al­
so be "b roken -in" . Be s ure to remembe r
this dur ing the fi rst 350 mi les (500 kilo ­
meters) . Brake gently . Avoid fo llow ing
closely behind other vehicles or other sit­
uations that m ight require sudden, hard
braking.
Avoid damaging the
vehicle
When you a re d rivi ng on poo r roads, or over
cu rbs, ste ep ramps, etc., ma ke certai n that
low- ly ing parts s uch as spoile rs and ex ha ust
s ystem parts do not bot tom o ut and get dam ­
aged.
T his is espec ially true for veh icles with low­
s lu ng chassis (s por ts chassis)* and fully load­
ed vehicles.
Driving through water
on roads
Note th e following to avoid ve hicle damage
whe n driving through water, for examp le on
flooded roads:
- The wa ter must not be any hig he r th an the
bottom of the vehicle body .
- Do not dr ive faste r than walk ing speed.

Avoid full throttle
Driving at moderate speeds saves fuel and
improves your mileage.
""Try and keep well below your car's maximum
speed.
Accelerating gently reduces fuel consump­
tion, engine wear, and does not disturb the
environment.
Fu el consumption, exhaust emissions and en ­
g ine noise increase disproportionately at high
speeds. If you drive at approximately three
quarters of top speed, fuel consumption will
be reduced by one half. Never drive faster
than the posted speed limit and weather con­
ditions permit .
Reducing unnecessary idling
Even when your car is just idling it burns up
fuel.
""Shut the engine off when you are not driving
the vehicle.
"" Do not warm up the vehicle by letting the
engine run at idle .
It makes sense to shut
off the engine in traff ic
jams, when waiting for trains to pass at ra il­
road crossings, or at traffic lights that have
l ong wa its on red. Turning the engine
off for
just
30-40 seconds saves more fue l than is
burned starting the engine again .
It takes a long time for the engine to warm up
fully when it is running at idle. However, wear
and noxious emissions are especially high
when the engine is warming up. So you should
drive away as soon as you start the engine and
avoid running at high rpms while the engine is
still warming up.
(D Note
Do not leave engine idling unattended af­
ter starting . If warning lights should come
on to indicate improper operation, they
would go unheeded. Extended idling also
produces heat, which cou ld result in over-
Driving and environment 187
'
heating or othe r damage to the vehicle or
other property.
Regular maintenance
A badly tuned engine unnecessarily wastes a
lot of fuel.
""H ave your veh icle serviced at regular inter-
vals.
By having your vehicle regu larly serviced by an
au thorized Aud i dea ler helps to ensure that it
runs properly and economic all y. The condition
of your veh icle not on ly affects its safety and
ability to hold its va lue, it a lso affects
fuel
consumption .
Check your oil each time you fill your tank.
The amount of o il used is related to engine
load and speed.
It is normal for the oil consumption of a new
engine to reach its lowest value after a certain
mileage has been driven.
You must drive your vehicle about 3,000 miles
(5,000 kilometers) before you can properly
assess oil consumpt ion.
This also app lies to fue l consumption and en­
gine output.
(U) Note
- Have your vehicle maintained properly
and in accordance with the service rec­
ommendations in your Warranty
& Main­
tenance booklet. Lack of proper mainte­
nance as well as improper use of the ve­
hicle will impair the function of the
emission control system and could lead
to damage.
- Do not alter or remove any component of
the Emission Control System unless ap­
proved by the manufacturer.
- Do not alter or remove any device, such
as heat shields, switches, ignition wires,
valves, which are designed to protect
your vehicle's Emission Control System
and other important vehicle compo­
nents .
•
•

bird d ropp ings as soon as possib le, since the
corrosive chemica ls in them wi ll cause the
rubber impregnat ion in your top to swell and
possibly allow the fabric to leak.
With
normal soiling , all yo u need to do is
clear the top with a soft brush and clear wa­
ter . Always brush in the direction of the fabric
from front to rear.
If the top is
very dirty and has spotted areas
clean it with a brush using a convertible top
cleaner . Always brush in the direction of the
fabric from front to rea r. Rinse w ith plenty of
clear water, and allow the top to air-dry .
Chamo is are not suitable for drying the top .
Never use gasoline, spot remover, benze ne,
pa int thinner or so lvents to remove spo ts. We
recommend that you only use cleaners espe ­
cially formu lated for use on convertible tops ,
and that you follow the produce use di rections
caref ully. Authori zed A udi deals can p rovide
deta iled information.
A WARNING
Always read and heed all WARNINGS and
the information on ¢
page 189.
Never use a high-pressure power washer to
clean the power top.
Wind deflector
App lies to vehicles: with wind deflector
Clear the wind deflector with water or, if it is
heav ily soiled, a chemically neutra l cleaning
solut io n.
A WARNING
Always read and heed a ll WARNINGS and
t he information on
¢page 189.
Sensors and camera lenses
-Remove snow wi th a hand brush and remove
ice with a de-icing spray that does not con­
ta in solvents .
Cleaning and protec tion 193
- Clean the sensors (adap tive c ruise control *,
parking system *) with a cleaning so lution
that does not contain so lvents and a soft
cloth.
@ Note
- If you wash your vehicle with a press ure
washer,
- make sure there is enough d istance to
sensors in the rear bumper.
- do not clean the camera lenses and the area a round them with the p ress ure
washer.
- N ever use warm o r hot wate r to remove
snow or ice from the came ra lens . This
c ou ld cause t he lens to crack.
- N ever clean the camera lens with abra­
sive products .
Waxing and Polishing
Waxing
A good wax coating protects the vehicle paint
to a la rge ex ten t agains t the envi ronmental
f a ctors lis ted under ¢
page 189, Washing and
even against s light scratches .
You can use a liquid car wax to protect yo ur
paint as soon as one wee k afte r you r vehicle
has been delivered.
Even if you regularly use a
wa xing process in
a utomat ic car washes, we recommend that
yo u manually a pply a coat o f wax to g ive the
pain t ex tra protection, par ticu larly if water no
longer beads on t he clean paint.
P rotect plast ic body parts w ith car wax in the
same w ay as the veh icle body .
During warm weather dead insects tend to
collect on the front bumper and on the fo r­
ward a rea of the hood. They are much easier
to remove from pa int that is waxed
often .
Polishing
Polish your vehicle only if the paint has lost its
shine and the gloss cannot be brought back
with wax . ..., •
•

194 Cleaning and protection
If the polish used does not contain preserva ­
tive compounds, the paint must be waxed af­
terwards .
_& WARNING
Always read and heed a ll WARNINGS and
other information
r::;, page 189.
([) Note
Do not use car wax on
- matte or anod ized metal trim
- r ubbe r o r r ubbe r-like tr im.
Trim strips
Metal trim needs special core.
For environmenta l reasons, Audi fabricates
the br ight tr im strips and t rim pieces from
pu re chromium-free a luminum.
Dirt and marks on the trim str ips should be
removed with a
pH-balanced cleaning agent
(do not use a chrome cleaner). Author ized
Aud i dealers carry clean ing products which
have been tested for use on your ve hicle and
a re not harm ful to the env ironment.
To avo id corros ion on the exterior tr im str ips,
only a pH-balanced solut ion should be used
fo r the w indshield washe r.
A WARNING
Always read and heed all WA RNI NGS and
other inform ation
r::;, page 189.
Plastic and vinyl
Plastic needs special core.
Use a clean, damp cloth or sponge to remove
dust and ligh t surface dir t. For other soil, use
a lukewarm all-purpose clea ning solution or a
mild saddle soap for viny l trim. Remove wate r
spots and tr aces o f so ap wit h a cl ean, damp
cloth or sponge . Use a clean, soft clot h to rub
d ry .
Grease, tar or o il stains can be removed w ith a
cle an cloth or sponge so aked w it h a ll-p urp ose cl
eaner or with a so lvent designed espec ia lly
to clean vinyl.
Oc cas ional ly app ly a colo rless v inyl or le athe r
preserva tive to re tain the m ater ia l's lus ter
and pliability.
A WARNING
'
A lways read and heed all WAR NIN GS a nd
other info rmation
r::;, page 189.
Aluminum trim
Use only neutral -pH products to remove spots
and deposits from a luminum surfaces.
Chrome care products and a lkaline cleaners
will attack a luminum surfaces and can dam­
age them over t ime.
A WARNING
A lways read and heed all WAR NIN GS and
o ther info rmat ion
r::;, page 189.
Touch-up paint
Minor point damages should be touched up
immediately.
"' Use eit her a touch-up paint stick or spray
pa int to cover m ino r scratches and nicks.
Your a uthorized Audi dea ler has touch-up
paint fo r minor scratches and stone chips.
Scratches should be touched up soon after
they occ ur to prevent corrosion.
If a spot starts to rust, however, a s imple
touch-up job will not be enough. T he affected
su rface must be sanded smooth and coated
with an anti- rust p rime r before the painted
finish can be restored.
The number for the orig inal veh icle pai nt can
be fo und o n the vehicle identification label
r:::;, page 261.
A WARNING ~
Always read a nd heed all WARNI NGS and
other informatio n
r::;, page 189.

198 Cleaning and protection
8_ WARNING
Solvents can change the properties of
some plastics and make it harder for the
airbag to deploy.
-
-Never clean the instrument panel or the
surface of airbag modules with cleaning
products that contain solvents .
- Products containing solvents will make
the surface of this part porous.
- Serious injuries can result if plastic parts
come loose when the airbag is deployed.
- Always read and heed all WARNINGS and
other information ¢
page 189.
(D Note
Cleaning agents containing solvents will
attack the material and can change the
way it behaves.
Natural leather
App lies to vehicles: with natura l leather
Audi makes great efforts to maintain the
properties, natural look and feel of interior
leather.
General
We offer many different types of leather on
our vehicles. Most are different types of nappa
leather, which has a smooth surface and
comes in various colors.
The intensity of the color determines the visu­ al characteristics and appearance. If the sur­
face of the leather has a typical natural look,
then the leather is a nappa leather that has
been left in a relatively natural condition. This
leather offers particularly good comfort and
breathes well. Fine veins, closed grains, insect
bites, skin folds , and subtle variations in color
remain visible. These characteristics demon­
strate that the material is natural.
Natural nappa leather is not covered by a col­
or finish.
It is therefore more sensitive to soil­
ing and wear, which is something you need to
consider if children, animals or other factors
might prove to be particularly hard on the
leather. By contrast, leather types that are covered by
a colored finish layer are more durable.
This
has a positive effect on the leather's resist­
ance to wear and soiling in daily use. On the
other hand, the typical characteristics of natu­
ral leather are barely or not apparent . Howev ­
er, this does not mean that the leather itself
is of inferior quality .
Care and handling
Because of the exclusive nature of the types of
leather that Audi uses and their unique prop­
erties (such as sensitivity to oils, grease, soil­
ing, etc.), you will need to be somewhat care­
ful with these leathers, and a certain type of care is required . For example , dark clothing
materials can discolor leather seats (especial­
ly if such clothing is damp and was not dyed
correctly). Dust and dirt particles in pores,
folds, and seams can have an abrasive effect
and can damage the leather surface as well as
weaken seams.
The leather should be cleaned regularly as
needed. After having been used for a relatively
long time, your leather seats will acquire a
rich aged finish. This is a characteristic of nat­
ural leather and a sign of true quality.
In order to maintain the value of this natural
product over the life of your vehicle, you
should follow the recommendations below:
(D Note
- To keep your leather from bleaching out,
do not allow it to be exposed to bright
sunlight for long periods of time. If you
have to leave the vehicle parked outside
for long periods, cover the leather to
protect it from direct exposure to sun­
light.
- Sharp objects on clothing, such as zip­
pers, rivets or sharp pieces on belts can
leave permanent scratches or scrape
marks on the surface of the leather.
(D Tips
-After each time you clean the leather and
at regular intervals, use a leather
1111>

preservative cream that contains UV­
blockers and that works into the leather .
This cream w ill nourish and mo istur ize
the leather, he lp ing it to breathe and
stay supple. It also helps to build up a
protective coating on the surface.
- Clean the leather every 2 - 3 months,
and clean any areas that get soiled.
- Remove fresh marks made by ballpoint pens, ink, lipst ick, shoe polish, etc. as
soon as possib le.
- Preserve the color of the leather as need­
ed by using a special colored leather care
cream to touch up areas of uneven color.
Cleaning and caring for leather
upholstery and trim
Applies to vehicles: with natural leather
Natural leather requires special care and at­
tention.
Norm al cleaning
.,. Clean soiled areas with a slightly mo istened
cotton or woolen cloth.
Mor e stub born dir t
.,. More stubborn dirt can be removed using a
cloth saturated with a m ild soap so lution (2
tablespoons m ild liquid soap) .
.,. Never allow the soap solution to saturate
the leather, and make certa in that no water
soaks into the seams .
.,. Wipe off the soap solution with a soft, dry
cl oth.
Cleaning spots
.,. Remove fresh w ater -b ased spots (such as
coffee, tea, ju ices, blood) w ith an absorbent
cloth or paper towel.
.,. Remove fresh
grea se or oil -based spot s
(such as butter, mayon naise , chocolate) wi th
an absorbent cloth or paper towe l, or use
the cleaner from the leat her ca re kit i f the
spot has not yet penetrated into the s urface
of the leather .
.,. Use an oil/grease dissolv ing spray, if
oil /
grease spots h ave d ried on.
Cleaning and protec tion 199
.,. Remove specific kinds of spots (ballpoint
pe n, fe lt marker, fingernai l polish, water­
based pa int, shoe po lish, etc .) with a spot
remover specifically formu lated for leather.
L e ather care
.,. Every half yea r use an approved leather care
product (available from your authorized
Audi dea ler) to ca re for the leather .
.,. App ly the product very spar ingly.
.,. Wipe it off w ith a damp cloth.
If you have any q uestions about cleaning and
caring for the leather in your vehicle, it is best
to contact your authorized Audi dealer, who
will be glad to help you and tell you about our
full range of leather care products, such as :
- Leather cleaning and care kit
- Creams to ca re fo r colored leather
- Spot removers for ballpoin t pens, shoe pol-
ish, etc.
- Oil/grease d issolving spray
- New and upcom ing products .
.&_ WARNING
Always read and heed all WARN INGS and
other in formation
r:!) page 189 .
(D Note
- Never use chem ica l so lvents (e .g . lighte r
fluid, tu rpe nti ne), waxes, s hoe polish o r
simi la r prod ucts on the lea ther surfaces
i n yo ur Audi .
- To avoid damage, have stubbo rn sta ins
removed by a comme rcial clean ing spe­
c ialist .
Cleaning Alcantara ® (synthetic suede)
Applies to vehicles: with Alcantara® upholste ry
R emoving du st and dirt
.,. Moisten a cloth, squeeze out excess water
and wipe down the seat surfaces .
Removing stains
.,. Moisten a cloth with lukewa rm wate r or
w ith di luted
ethyl (rubbing ) alc ohol.
•
•

200 Cleaning and protec tio n
• Dab at the stain . Start at the outside and
work inwards .
• Once the stain is no longer visib le, use a soft
dry cloth or tissue to soak up the moisture.
Do not use leather cleaning products on Al­
cantara ®.
You may use a suitable shampoo for remov ing
dust and dirt .
Dust and grit in the pores and seams can
scratch and damage the surface. If the car is
l eft stand ing in the sun for long periods, the
A lcantara ® should be protected against direct
sunlight to prevent it from fading. Slight color
variations will develop in normal use and are
not an indication of material deterioration .
@ Note
-Never use chemical solvents (e.g . lighter
fl uid, turpentine), waxes, shoe polish or
similar products on Alcantara ® surfaces .
- To avoid damage, have stubborn stains
removed by a commercial cleaning spe­
cia list.
- Do not use brushes, stiff sponges or sim­
ilarly abrasive cleaning aids.
Safety belts
Only well-maintained safety belts work relia­
bly when needed .
• Keep be lts clean .
• For cleaning, use a mild soap and water sol­
ution . Let be lts dry thoroughly and away
from direct sunlight.
• Do not allow inertia reel safety belts to re­
tract before they are completely dry.
• Check the condition of your safety belts
reg ­
ularly .
Heavily soiled safety belts may not retract
properly .
A WARNING
Damaged safety belts can break in a crash.
-Anything that might damage your safety belts could mean that you and your pas­
sengers would not be adequate ly pro­
tected in an accident.
- Safety belt performance depends on cor­
rect insta llation. Never remove be lts
from the veh icle to clean them .
- Do not use chemical clean ing agents,
bleach or dyes. T hey have corrosive prop­
erties which weaken the webb ing .
- When clean ing your safety belts, inspect
them for damage. If you discover dam­
age, see your authorized Audi dealer .
-Always read and heed all WARNINGS and other information
Q page 189 .
Engine compartment
Be especially careful when cleaning the en­
gine compartment.
Al ways s witch off the ign it ion befo re clea n­
ing the engine ¢ Li:::,..
Plenum panel
Remove leaves from the plenum panel in front
of the windshield under the engine hood . This
prevents the water drain holes from becoming
blocked, and it prevents debris from enter ing
the vehicle interior through the heating and
ventilat ion ducts.
Corro sio n p rot ection
T he engine compartment and transmission
have been corrosion-protected at the factory .
Good anti- co rrosion treatmen t is very impor­
tant, particu larly in the w inte r.
If the vehicle
is frequently driven on salt treated roads, the
entire engine compartment and plenum panel
shou ld be thoroughly cleaned at the end of
winter and retreated to prevent salt damage.
At the same time, the underside of the vehicle
should be washed as well. .,..