2013 AUDI A8 reset

10 Instruments and warning/indicator lights
Instruments and warning/indicator Lights
Instruments
Instrument cluster and controls
The instrument cluster is your central source of information.
Fig. 3 Overview of th e instr ume nt cluster
(!) Coolan t tempera ture gauge ...
@ Tachometer (engine rev counter)
® Turn signals ............. .. .
© D isp lay with
- Driver information system ...
- Warning/ind icator lights
® Tachom eter
® F uel gauge .... ..... ... ... . .
0 Reset b utton for trip odometer
(D Tips
1 0
11
47
23
11
1 1
26
The instrument illumination (for dia ls and
needles) t urns on when the ignition is on
a nd the vehicle lights are tur ned off. As
the daylight fades, the illumination of t he
dia ls likewise dims automatica lly and w ill
go o ut comple tely when the o utsi de light
i s very low. Th is feature is meant t o rem ind you
to sw itch on the head ligh ts when o ut­
s id e light condi tions become poor .
Engine coolant temperature gauge
The engine coolant gauge (!) ¢ poge 10, fig. 3
only works when the ignition is on. To prevent
damage to your engine, please note the fol­
lowing important po ints:
Engine cold
If only the LEDs at the bottom of the gauge
turn o n, the engine has not reached operating
temperature yet. Avoid hig h engine speeds,
heavy engine loads and heavy throttle applica­
tions .
Normal temp erature
The eng ine has reached its operating temper-
at ure once the LEDs up to the center of the .,.

24 Instruments and warning /indicator lights
to ice on the road ¢ & . If the vehi cle is
stationary, o r if you are dr iving at a very
l ow speed, the tempe rat ure shown in the
display might be slightly higher t han the
actua l o utside temperature. This is
ca used by the heat being rad iated from
t h e eng ine.
- You can se lect the un its used for temper ­
atu re, speed a nd other measurements in
the MMI.
- Fo r informat ion on the a udio/video and
nav iga tion* functions, refer to the sepa­
r ate MMI owner's manual.
Operation
The driver information system is operated us­
ing the buttons on the multifunction steering
wheel.
ffi
------,±.
~
Fig. 6 Multifunct ion steer ing wheel: operating "the driv­
e r info rmatio n system
Fi g. 7 Driver infor mat ion syste m: opening t he ve hicle
functio ns me nu
Operating concept
.. Swi tch the ignition on.
.. To sw itch between the tabs, press the ro ck­
er switch @to the left or righ t
c:::> fig. 6.
.. To access addi tio nal in fo rmat ion be low or
above, rotate t he thumbw heel @ dow n or
up. ..
To confirm a select ion, press t he thumb­
wheel @.
Accessing Vehicle functions
.. Sele ct the first tab wit h the ro cker swi tch
@ .
.. Press t he bu tton l==L Th e Vehicle functions
menu a ppears c:::> fig . 7.
.. To se lect a menu item, tu rn and press t he
thumbwhee l
®·
Resetting values to zero
.. Sele ct the on-board computer / Efficiency
program
menu item in the Vehicle func­
tions
men u.
.. Yo u can now select between the long-term
memory and short-term memory.
.. To reset the values in a memory, press and
hold th e thumbw heel @ for one second.
The last function selected d isp lays when you
switch the ignition on .
On-board computer
You can ca ll up the fo llowi ng i nformation in
the on -boar d computer:
- Dat e
- Dr iv ing t ime (h) fro m the short-term memo-
ry
- Average consumption in MPG ( l/100 km)
from the short-te rm memory
- Average speed i n mph (km/h) from the
short-te rm memory
- Distance driven in miles (km) from the
short-term memory
- Current fuel consumption in MPG ( l/100
km)
- Short-term memory overview
- Long-te rm memory ove rview
T he short-te rm memory collec ts dr iv ing in for­
mation from the time the ig nition is switched
o n unti l it is switched off. If you continue driv­
ing within two ho urs after switch ing the ign i­
tion off, the new values are incl uded when cal­
cu lating the cu rrent trip information .
Unli ke the short-term memory , the long-term
memo ry is not erased automatically. Yo u can ..,.

Instrument s and warning /indicator lights 25
select the time period for evaluat ing trip in­
formation yourself.
F or some veh icle functions, you can access the
t r ip information from the temporary memory
in the
line @~page23, fig. 5.
The current fuel consumpt ion can be dis­
p la yed using a bar ~
page 26, fig. 10. The
average consumption (mpg) stored in the
short-term memory is also displayed. Electri­
cal energy can be stored in the battery when
the vehicle is coast ing or driving downhill (re­
cuperation) . The bar will move toward D.
Efficiency program*
The eff ic iency program can help you to use
l ess fuel.
It evaluates driving information in
reference to fue l consumption and shows oth ­
er equipment influencing consumption as well
as shift recommendations.
q page 25. Fuel
economy messages
q page 25 provide tips
for efficient driving. The effic iency program
uses distance and consumption data from tr ip
computer
1.
To display the efficiency program, call up Ve­
hicle functions and select the menu option
Efficiency prog ram . If the data are deleted in
the efficiency program, those values are also
reset in trip computer.
(D Tips
- All stored values w ill be lost if the veh i­
cle battery is disconnected.
- Fuel consumptions (average and cur­ rent), range and speed are displayed in
metric units on Canadian models.
Other equipment
Applies to vehicles: with efficiency program
Fig. 8 Trip computer: ot her equipment
Requirement: The efficiency program must be
displayed
q page 25.
.,. Turn the thumbwheel until the other equip-
ment appears in the display .
Other equipment that is currently affecting
fuel consumption is listed in the efficiency program . The display shows up to three other
items of equipment @. The equ ipment using
the most fuel is listed first. If more than three
items using fuel are switched on, the equip­
ment that is currently using the most fuel is
displayed .
A scale ® also shows the current total con­
sump tion of all other equipment.
Fuel economy messages
App lies to vehicles: with efficiency program
Fig. 9 Disp lay : example o f a fu el econo my m essa ge
Fuel economy messages are displayed when
fuel consumption is increased by certain con­
ditions. If you follow these fuel economy mes­
sages, you can reduce your vehicle's consump­
tion of fuel. The messages appear automati-
cally and are only displayed in the efficiency
111,,

26 Instruments and warning/indicator lights
program. The fuel economy messages turn off
automatically after a certain period of time.
.,. To turn an economy message off immedi-
ately after it appears, press any button on
the multifunction steering wheel.
@ Tips
- Once you have turned a fuel economy
message off, it will only appear again af­
ter you turn the ignition on again.
- The fuel economy messages are not dis­
played in every instance, but rather in in­
tervals over a period of time.
Cylinder on demand System
Applies to vehicles: with 4.0 TFSJ engine
Fig. 10 Instrument duster: fuel consumption
To save fuel, the engine automatically turns
four cylinders on or off, depending on the
amount of power needed. This action is not
felt by the passengers.
Displaying cylinder mode
Requirement: the on-board computer is dis­
played
~ page 24.
.,. Turn the thumbwheel until the current fuel
consumption display is shown in the instru­
ment cluster.
If the green bar is displayed,
you are driving in 4-cylinder mode.
Basic requirements for 4-cylinder mode
4-cylinder drive mode is used automatically if
certain basic requirements are fulfilled. These
include:
- A low power output requirement.
- Driving in third gear or higher.
- Engine speed between 960 and 3,500 RPM. - A warm engine.
Odometer
Fig. 11 Instrument cluster Odometer and
reset button
The odometer shows you how many miles
(kilometers) you have driven. You can switch
the display from miles to kilometers and vice
versa via the MMI.
Upper odometer
The trip odometer shows the distance driven
since it was last reset. It can be used to meas­
ure short distances. The last digit indicates
1/10 of a mile (100 meters).
You can reset the trip odometer to zero by
pressing the Reset button
Efil.
Lower odometer
The lower odometer shows the total number
of miles (kilometers) driven.
Malfunction message
If there is a malfunction in the instrument
cluster,
DEF will appear in the trip odometer
display area. Contact your authorized Audi
dealer to have the problem corrected .
Time and date display
Fig. 12 Center console: analog clock

Instrument s and warning /indicator lights 2 7
The date and time are shown in the instru ­
ment cluster display ¢
page 23, fig. 4. There
is also an ana log clock in the center conso le
¢fig. 12.
When you open the drive r's door, the date and
time appear in the instrument cluster display for 30 seconds. When the ign ition is switched
on, the time is always displayed in the status
line © regard less of the current d isp lay.
You can set the time on both clocks and the
date display in the MMI. Refer to the M MI
owner's manual for instructions.
Service interval display
The service interval display reminds you when
your next service is due.
Fi g. 1 3 In st rume nt cluster: Service interva l d isp lay
The schedule for the next oil change o r inspec­
tion is calculated a utomatically and displayed
according ly. The display works in two stages:
Service reminder
30 days before the next service is due, a serv­
ice reminder appears in the display when you
switch the ignition o n
r:::;,fig. 13.
After abo ut 5 sec onds the display sw itches
back to n ormal. The d istance and time re­
maining are updated each time the ignition is
switched on until the date due for serv ice is
reac hed.
Service due
W hen the due date for service is reached, the
message
Service due! appea rs in the instru­
ment clus ter immediately after you switch the
i gnit io n on . Additionally, a war ning tone sou
nds. After about 5 seconds the disp lay
switc hes back to normal.
Calling up the service schedules
If or w hen an oi l change or inspection is due,
c a n be shown in the M MI di spl ay by selec ting
t h e service in terval d isplay in the c ar menu .
Se lect the
I CAR I function button > Car s ys­
tems
control button > Ser vicing & checks >
Service interval d isp lays.
Resetting the service interval display
Your auth ori zed Audi de aler will reset the cor­
responding service sc hedule a fter pe rforming
t h e a ppropriate service o n your vehicle. You
also have t he possibility to reset the oil
change schedule after hav ing performed a n
o il change according to Aud i specifications.
Se lect the
ICAR I function button > Car sys­
tems
con trol button > Servicing & che cks >
Service Intervals > Reset oil change interval.
(D Note
If you d isconnect t he battery te rm inals , no
ca lculat ions can be made fo r the service
i nte rva l disp lay dur ing th is time and no
se rv ice rem inde r will appear. Remem ber
th at obs erving the prop er servi ce inte rva ls
i s vi tally imp ortant t o extending the lif e of
you r ve hicl e, p articu larly the engine, an d
maintain ing its val ue. Eve n if the milea ge
dr iven is low, the maximum period of one
year from one service to the next m ust n ot
be exceeded.
(D Tips
- Do not reset the display between oil
chan ges, otherwise the disp lay wi ll be in­
co rrect.
- The i nfo rmation in the Service Reminder
remains stored eve n when t he ve hicle
battery is disconnected.

The stored speed and the indicator light
A;(l)~i4 (US mode ls) 8 (Canad ian mode ls) ap­
pear in the instrument cluster d isp lay
¢ fig. 92. The display may vary, depending on
t he type of d isplay in your vehicle.
The speed is k ept constant via an engine out­
put adjustment or act ive brake intervention .
A WARNING
-Always pay attention to traffic even when
the cruise control is switched on . You are
always responsible for your speed and
the distance between your vehicle and other vehicles.
- For safety reasons, the cruise control
should not be used in the city, in stop­
and-go traff ic, on twisting roads and
when road conditions are poor (such as
ice, fog, grave l, heavy rain and hydro ­
planing) -risk of accident .
- Turn off the cruise control temporari ly
when entering turn lanes, highway exit lanes or in construction zones.
- Please note that inadvertently "rest ing "
yo ur foot on the accelerator peda l causes
the cruise control not to brake. This is
because the cruise control is overridden
by the driver's acce leration.
- If a brake system malfunction such as
overheating occurs when the cruise con­
trol system is sw itched on, the braking
function in the system may be switched
off. The other cruise control functions re­
main active as long as the indicator light
[~jlQ~i4 (US models) I ii (Canad ian mod­
els) is on.
The brake lights illuminate as soon as the brakes decelerate automat ically .
Changing speed
" To increase/dec rease the speed in incre­
ments , tap the lever in the
0 10 d irection
¢ page 90, fig. 91 .
On the ro ad 91
" To increase/decrease the speed quick ly,
hold the lever in the
0 10 direction until
the desired speed is displayed.
You can also press the accelerator pedal down
to increase your speed, e.g . if you want to
pass someone . The speed you saved earlier
will resume as soon as you release the accele r­
ator pedal.
If, however, you exceed your saved speed by
6 mph (10 km/h) for longer than S minutes,
the cruise contro l wi ll turn off temporari ly.
The green symbol
A;(l )~i4 (US models) 8 i n
the d isplay is replaced with a white symbol.
The saved speed remains the same .
Presetting your speed
You can preset your desired speed while the
vehicle is not moving .
" Switch on the ignition.
" Pull lever into posit ion
(D ¢ page 90,
fig . 91 .
" Press the lever in the 0 or 0 direction to
increase or decrease your speed .
" Release the lever to save that speed.
This function makes it possible, for example,
to save the speed you want before dr iving on
the h ighway. Once on the highway, act ivate
the cru ise con trol by pulling the lever toward
(D .
Switching the system off
T e mpor ary dea ctivat ion
" Press the brake pedal , or
" Press the lever into position @(not clicked
into place)
¢ page 90, fig. 91 , or
" Drive for longer than 5 minutes at more
than 5 mph (10 km/h) above the stored
speed.
S w itching off complet ely
" Press lever into position @(clicked into
place), or
" Switch the ignition off .

120 Automatic Transmission
Parking lock emergency release
The parking lock must be released using the
emergency release before towing the vehicle .
@
Fig. 126 Dr iver's side footwell: releasing t he park ing
lock us ing t he emergency release
Fig. 127 Drive r's s ide footwe ll: resetting th e pa rking
l ock
The emergency release is located under the
floor mat on the driver's side. You operate the
emergency re lease from the dr iver's seat.
Releasing the parking lock using the
emergency release
• To prevent the vehicle from rolling uninten­
tionally, set the park ing brake© ¢
page 85
or press the brake peda l.
.. There are two slits on the cover. Position
the screwdriver from the vehicle tool kit in
one of the s lits on the cover and pry the cov­
er off.
• Pull the band@ in the direction of the ar­
row until the release lever locks in place
¢ fig . 126.
• Fold the uppe r section of the release lever
down into the recess.
Resetting the parking lock
• Press the button @ and the release lever at
the same time . You can now push the lever back into its original pos
ition . Make sure the
lever locks in place
¢fig. 127.
.. Install the cover .
T he indicator light
[O] and the N position indi­
cator in the instrument cluster turn on when
the parking lock is released using the emer­
gency release . The message
Risk of rolling! P
not possible . Please set the park ing brake
a l­
so appears.
A WARNING
If you release the park ing lock using the
emergency release, secure your vehicle
with the pa rking brake or the brake pedal
i f the parking brake is not working. The ve­
hicle can roll away if it is not secured and
cause a crash.

268 Tires and wheels
and may affect the vehicle's handling and
stopping ability.
Please note that the TPMS is not a substitute
for proper tire maintenance, and it is the driv­
er's responsibility to maintain correct tire
pressure, even if under-inflation has not
reached the level to trigger illumination of the
TPMS low tire pressure telltale .
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate when
the system is not operating properly. The
TPMS malfunction indicator is combined with
the low tire pressure telltale. When the sys­
tem detects a malfunction, the telltale will
flash for approximately one minute and then
remain continuously illuminated. This se­
quence will continue upon subsequent vehicle
start-ups as long as the malfunction ex ists.
When the malfunct ion indicator is illuminat­
ed, the system may not be able to detect or
signal low tire pressure as intended . TPMS
malfunctions may occur for a variety of rea­
sons, including the installation of replace­
ment or a lternate tires or whee ls on the vehi­
cle that prevent the TPMS from functioning
properly. Always check the TPMS malfunction
telltale after replacing one or more tires or
wheels on your vehicle to ensure that the re­ placement or alternate tires and wheels allow
the TPMS to continue to function properly.
Tire pressure indicator appears
App lies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction .
Fig. 209 Display: underinflation warning
Fig. 210 Disp lay: System malfunction
Using the ABS sensors, the tire pressure moni ­
toring system compares the tire tread cir cum­
ference and vibration character istics of the in ­
dividua l tires. If the pressure decreases in one
o r more t ires, this is ind icated in the instru­
ment cluster with a warning symbol
[«E and a
message ~
fig. 209.
The tire pressure monitoring system must be
reset via MMI each t ime the press ures are ad­
justed (e.g. when switching between partial
and full load pressure) or after changing or re­
placing a tire on your vehicle
c::> page 269. The
TPMS indicator only monitors the tire pres­
sure that you have previously stored. You can
find the recommended tire pressures for your
vehicle on the label on driver's side 8-pillar
c::> page 2 53.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the tire pressure in one or more tires is too
low,
- the tire has structural damage ,
- the tire pressure was changed, wheels rotat-
ed or replaced but the TPMS was not reset
c::> page269.
Warning symbols
[tE Loss of pressure in at least one tire c::> ,1,. .
Check the tire or tires and replace or repair if
necessary. The indicator light
[tE in the instru­
ment cluster also illuminates
c::> page 11.
Check/correct the pressures of all four tires
and reset TPMS via MMI.
119;~, < T ire Pressure Monitoring System) Tire
pressure! System malfunction .
IJJ,-