12 Instruments and warning/indicator lights
disabled. It is also important to notify your in
surance company about the loss .
Setting the speed warning
By pressing the I SETI button br iefly, you can
set threshold 1 of the speed warning while
you are dr iv ing
~ page 79. By mainta ining
pressure on the ISETI button, you de lete the
warning threshold.
Digital clock with date display and
Odometer
Fig. 5 Instrument cl uster: odo meter
Fig. 6 Instrum ent cl uster : re se t button
Digital clock/GPS controlled clock*
Depending on the vehicle equ ipment level,
you may choose between the quartz clock or
the
GPS controlled clock* (!j in the radio or in
the MMI*. You can learn more about th is in
the MMI manual or in the radio user's manual.
Odometer /trip odometer
The display of distance dr iven is shown in kilo
meters "km" or in miles "mi".
- USA mode ls - Miles
- Canada models - Kilometers
T he units of measure (kilometers/miles) can
be changed in the radio or
MMI*. You can learn more about this in the MM
I manual or in
the radio user's manual.
T he odometer @ shows the total number of
kilometers or miles that have been driven on
the vehicle .
The trip odometer @shows the distance driv
en since it was last reset .
It can be used to
measure short distances. The last digit shows
distances of
100 meters or 1/10 of a mile.
T he trip odometer can be reset to zero by
pressing the reset button IO .OI
~ fig. 6.
Malfunction message
If there is a malfunction somewhere in the in
strument cluster,
DEF will appear in the trip
odometer and w il l stay on . Contact your au
thorized Audi dea le r to have the prob lem cor
rected.
Immobilizer
When the ignition is switched on, the data on
t h e ignition key are scanned automat ically .
If an unauthor iz ed key was used,
SAFE is dis
played permanently in the odometer display
field . The vehicle cannot be operated
~ page 33.
(D Tips
-When you switch off the ignition or open
the-driver door, the t ime, date, odome
ter and temperature are displayed for an
add itiona l
30 seconds.
- You can also call up the display with the
! SET !button
~page 11 wh ile the igni
tion is switched off.
· Fuel gauge
T he fue l gauge works only when the ignition is
on .
When the needle reaches the red area, the
warning light
Ii] in the instr ument cluster will
illuminate
Qpage 21 . Time to refuel!
The total tank capacity of your vehicle is listed
in
~ page 271. .,,.
-Do not raise the vehicle until yo u are
sure the jack is securely engaged.
- Passenge rs must not remai n in the
ve
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad
just as necessary and then contin ue to
ra ise the jack.
CD Note
Do not lift the vehicle by the si ll. Position
the vehicle jack only at the designated lift
ing points on the sill. Otherwise, your vehi
cle will be damaged.
Taking the wheel off /installing the spare
tire
Follow these instructions step-by-step for
changing the wheel.
Fi g. 189 Changing a wheel: using the screwdrive r han
dle (with the blade removed) to turn the bolts
Fig . 1 90 Changing a wheel: alignm en t pin ins ide t he
top hole
After you have loosened a ll wheel bolts and
ra ised the veh icle off the ground, remove and
replace the wheel as follows:
What do I d o now ? 257
Removing the wheel
.,. Remove the topmost whee l bolt completely
with the
he xagonal so ck et in the screwdriv
er handle (vehicle tool kit)
o fig. 189 and
set it aside on a
clean surface .
.,. Screw the threaded end of the
alignment
pin from the tool kit hand-t ight into the
empty bolt hole
o fig. 190.
.,. Then remove the other wheel bolts as de
scribed above .
.,. Take
off the whee l leav ing the a lignment
pi n in the bolt hole
o(D .
Putting on the inflat able spar e tire
.,. Push the spare tire over the alignment p in.
.,. Screw on the wheel bo lts and tighten them
slightly us ing the hexagonal socket .
• Remove the a lignment pin and inse rt and
tighten the rema ining wheel bolt slightly
like the res t.
.,. Turn the jack hand le co unter -clockwise to
lower the veh icle until the jack is fully re
leased .
.,. Use the wheel bolt wrench to tighten all
wheel bo lts f irm ly
o page 255 . Tighten
them
in a crisscross pattern, from one bolt
to the (approximately) opposite one, to keep
the wheel centered .
• Perfo rm the steps required afte r changing
the wheel
o page 254, After changing a
wheel.
T he hexagonal socket makes it easie r to re
move th e wheel bo lts from the rim. Care
sho uld be taken when remov ing the reversib le
blade .
CD Note
When removi ng or insta lling the whee l,
the r im cou ld hit the bra ke roto r and dam
age the roto r. Work carefu lly and have a
second person to help you .
(l} Tips
-When mount ing tires w ith unidir ectional
tread de sign
make sure the tread pat
tern is pointed the right way
o page258. II>-