
Child safety seats
Infant seats
Babies and infants up to about one year old
and 20 lbs. or 9 kg need special rearward -fac
ing child restraints that support the back,
neck and head in a crash.
Fig . 159 Sche matic overv iew: rearward-fac ing infant
seat, properly installed o n the rear seat
~ When using the vehicle safety belt to install
a ch ild safety seat, you must first activate
the convertible locking retracto r on the
safety be lt to prevent the child safety seat
from moving
¢ page 171 or install the seat
using the LA T CH attachments.
~ Push the child safety seat down with your
full weight to get the safety belt rea lly tight
so that the seat cannot move forward or
sideways more than one inch (2.5 cm).
~ Secure unused safety belts on the rear seat
¢page 166.
Infants up to about one year (20 lbs . or 9 kg)
are best protected in special infan t carriers
and child safety seats designed for their age
group . Many experts believe that infants and
small children should ride only in spec ial re
straints in which the ch ild faces the back of
the vehicle. These infant seats support the ba
by's back, neck and head in a crash
¢fig . 159.
The airbag on the passenger side makes the
front seat a po tentially dangerous place for a
child to r ide . The front seat is not the safest
p lace for a child in a forward -facing child seat.
It is a very dangerous p lace for an infant or a
l arger ch ild in a rearward-facing seat.
Child Safety 16 7
A WARNING
Not using a child safety seat, using t he
wrong child safety seat or improperly in
stall ing a ch ild restraint increases the risk
of ser ious personal injury and death in a
crash.
- Never install rearwa rd-facing child safety
seats or infant ca rr ie rs on the front pas
senger seat -even with an Advanced Air
bag Sys tem. A ch ild will be ser iously in
jured and ca n be killed when the inflat
ing airbag hits the child safety seat or in
fant carrier with great force and smashes the child safety seat and child against
the backrest, center armrest, door or
roof ¢
page 141, Child restraints on the
front seat- some important things to
know .
-Always install rea rward -facing chi ld safe
ty seats or infant carriers on the rea r
seat .
- Never install a rea rward -facing ch ild re
straint in the forward-facing direction .
Such rest ra in ts are designed for the spe
cial needs of infants a nd ve ry sma ll chil
d ren and cannot pro te ct them p roperly if
the seat is forward -facing.
- If you must insta ll a rearwa rd fac ing
child safety seat on the front passenger
seat because of exceptiona l circumstan
ces and the
PASSENGER AIR BAG OFF
light does not come on and stay on, im
mediately insta ll t he rearward-facing
child safety seat in a rear seating posi
tion and have the airbag system inspect ed by your autho riz ed Audi dealer .
- Always read and heed all WARNINGS
wheneve r us ing a child restrained in ave
h icle is being used ¢
page 132, Safety
belts,
Q page 140, Airbag system and
¢ page 161, Impor tan t thi ngs to know .

168 Child Safet y
Convertible child safety seats
Properly used convertible child safety seats
can help protect toddlers and children over
age one who weigh between
20 and 40 lbs. (9
and 18 kg) in a crash.
Fig . 160 Sche matic overv iew : ins tallat ion of t he at
t a chments appl icable to a LATCH seat
Fig. 161 Sche matic overview: in sta llat ion of t he sea t
us ing t he veh icle's safety be lt system
.. When using the vehicle safety be lt to install
a chi ld safety seat, you must f irst activate
the convertible locking feature on the safety
belt to prevent the child safety seat from
moving
c::> page 171 or insta ll the seat using
the LATCH attachments .
.. Push the child safety seat down with your
full weight to get the safety belt really t ight
so that the seat cannot move forward or s ideways more than one inch (2.5 cm)
c::> page 171.
.. Secure unused safety bel ts on the rear sea t
~page 166.
A toddler or child is usually too large for an in
fant restraint if i t is more than one year old
and weighs more than 20 lbs . (9 kg).
Toddle rs and ch ildren who are o lder than one
yea r up to about 4 years o ld and weigh more
than 20 lbs. (9 kg) up to 40 lbs. (18 kg) must always be proper
ly restrained in a child safety
seat certified for the ir size and weight
~ fig. 160 and r:!) fig . 161 .
The airbag on the passenger side makes the
front seat a potentia lly dangerous place for a
c h ild to ride. The front seat is not the safest
place for a child in a forward-facing child safe
ty seat. It is a very dangerous place for an in
fant or a larger ch ild in a rearward-facing seat.
A WARNING c=
Not using a child safety seat, us ing the
wrong child safety seat or imprope rly in
stalling a ch ild restra int increases the risk
of ser ious personal in jury and death in a
collis ion or o ther emerge ncy sit uat ion.
- Ch ild ren on the front seat of any ca r,
even with Advan ced Airbags, can be seri
ously injured or even k illed when an air
bag inflates. A chi ld in a rearwa rd -facing
child safety seat installed on the front passenger seat will be serio usly injured
and can be killed if the front airbag in
flates -even with an Advanced Airbag
System .
-
-The inflating airbag will h it the ch ild
safety seat or infant carrier with great
force and will smash the child safety seat
and child aga inst the back rest, center
armrest, doo r or roof .
-Always install rearward-facing ch ild safe
ty seats on the rea r seat .
- If you must install a rearward fac ing
child safety seat on the front passenger
seat because of exceptiona l circumstan
ces and the
PA SSENGER AIR BAG OFF
light does not come o n and stay on, im
mediately insta ll the rearward-facing
child safety seat in a rear seating posi
tion and have the airbag system inspect
ed by your authorized A udi dealer.
- The rear side of the child safety seat
should be pos itioned as close as possib le
to the backrest on the vehicle seat.
- Always read and heed all WARNINGS
whenever using a child restrained in ave-
h icle is being used
c::> page 132, Safety ll>-

-If the PA SS ENGER AIR BAG O FF light
does not come o n an d stay on, perform
the checks described
c:> page 151, Moni
toring the Advanced Airbag System .
-Take the child restraint off the front pas
senger seat and install it properly at one
of the rear seat positions if the
PAS SEN
GER AIR BAG OFF
light does not stay on
whenever the ignition is switched on.
- Always read and heed all WARNINGS
whenever using a child rest rained in ave
hicle is being used
c:> page 132, Safety
belts,
c:> page 140, Airbag system and
c:> page 161, Important things to know.
Installing a child safety
seat
Securing a child safety seat using a
safety belt
Safety belts for the rear seats and the front
pas senger's seat can be locked with the con
vertible locking retractor to properly secure
child saf ety seat s.
The safety belts eme rgency lock ing re tracto rs
for the re ar seats safety belts and for the
front passenger 's seat sa fety belt have a con
ve rtible locking retractor for child restraints.
The safety belt must be locked so that belt
webbing cannot unreel. The retractor can be
activated to lock the safety belt and prevent
t he safety belt webbing from loosening up
during normal driving . A child safety seat can
only be properly installed when the safety belt
i s locked so tha t the child and ch ild safety
seat will stay in place.
Always remember: Even though your veh icle is
equ ipped w it h an Advanced A irbag system, all
chi ld ren , espec ia lly those 12 yea rs and yo ung
e r, should always ride in the back seat proper
l y rest rained for thei r age and weig ht.
~ WARNING
Improperly insta lled child sa fety seats in
crease the risk of ser ious personal inju ry
and death in a collision.
Child Sa fet y 1 71
-Always ma ke sure that the safety be lt re
tractor is locked when insta lling a child
safety seat. An unlocked safety belt re
tracto r cannot hold the child safety seat
in place dur ing no rma l dr iving o r in a
crash .
- Always buckle the child safety seat firmly
in place even if a ch ild is not sitt ing in it .
A loose child safety seat can fly around
du ring a s udden stop or in a collision.
- If t he backrest is not securely latched,
the child and the child res traint will be
thrown fo rward togethe r with the bac k
rest and wi ll stri ke par ts of the ve hicle
interior. The child can be seriously i n
jured or killed .
- Never install rearwa rd -fac in g ch ild safety
seats or infant ca rrie rs on the front pas
senger seat . A child will be serio usly in
jured and can be killed when the passen
ger airbag inflates .
- The inflating airbag will h it the ch ild
safety seat or infant carrier with great
force and will smas h the child safety seat
and child against the backrest, center
armrest, doo r or roof .
- Always install rearward-facing chi ld safe
ty seats or infant carriers on the rea r
seat.
- Forward-facing child safety seats or in
fant carriers installed on the front pas
senger's seat may interfer e with the de
ployment of t he a irbag and cause serious
in jur y to the child.
- I t is safer to install a forwa rd-facing
child safety seat on t he rear seat.
- Always read a nd heed a ll WAR NIN GS
wheneve r us ing a chi ld restrained in ave
hicle is being used
c:> p age 161. Special
prec autions apply when instal ling a child
safety seat on the fron t passenger seat
c:> page 141, Child restraints on the front
seat -some important things to know.
A WARNING
A lways take specia l precautions if you
must install a forward or rearward-facing •
•

172 Child Safety
child restraint on the front passenger's
seat in exceptional situations:
- Whenever a forward or rearward-facing
child restraint is installed on the front
passenger seat, the
PASSENGER AIR
BAG OFF
light must come on and stay on
whenever the ignition is switched on .
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, perform
the checks described
<::) page 151, Moni
toring the Advanced Airbag System .
- Take the child restraint off the front pas
senger seat and install it properly at one
of the rear seat positions if the
PASS EN·
GER AIR BAG OFF
light does not stay on
whenever the ignition is switched on.
- Improper installation of child restraints
can reduce their effectiveness or even
prevent them from providing any protec
tion.
- An improperly installed child restraint
can interfere with the airbag as it de
ploys and seriously injure or even kill the
child.
- Always carefully follow the manufactur
er's instructions provided with the child
safety seat or carrier.
- Never place additional items on the seat
that can increase the total weight regis
tered by the weight-sensing mat and can
cause injury in a crash .
.&_ WARNING
Forward-facing child restraints:
- Always make sure the forward-facing
seat has been designed and certified by
its manufacturer for use on a front seat
with a passenger front and side airbag.
- Never put the forward-facing child re
straint up, against or very near the in
strument panel.
- Always move the passenger seat into its
rearmost position in the seat's fore and
aft adjustment range, as far away from
the airbag as possible before installing
the forward-facing child restraint. The backrest must be adjusted to an upright
position.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched
on.
.&_ WARNING ~
Rearward-facing child restraints:
- A child in a rearward-facing child safety
seat installed on the front passenger
seat will be seriously injured and can be killed if the front airbag inflates - even
with an Advanced Airbag System .
- The inflating airbag will hit the child
safety seat or infant carrier with great
force and will smash the child safety seat
and child against the backrest, center
armrest, door or roof.
-Always be especially careful if you must
install a rearward facing child safety seat
on the front passenger seat in exception
al circumstances.
-A tight tether strap on a rearward-facing
child restraint attached to the front pas
senger seat can put too much pressure
on the weight-mat in the seat and regis
ter a heavier weight in the Advanced Air bag System. The heavier weight regis
tered can make the system work as
though an adult were on the seat and de
ploy the Advanced Airbag when it must
be suppressed causing serious or even
fatal injury to the child.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched
on.
- If the PASSENGER AIR BAG OFF light
does not come on and stay on, immedi
ately install the rearward-facing child
safety seat in a rear seating position and
have the airbag system inspected by your
authorized Audi dealer.

188 Driving and en vironm ent
8_ WARNING
After driving through water, mud, slush,
etc ., the brakes may be slow to take effect
because of wet brake rotors and pads. Dry
the brakes first by braking carefully to re
store the full braking effect.
CD Note
Vehicle components such as the engine,
transmiss ion, suspension or electrical sys
tem can be severely damaged by driving
through wate r.
@ Tips
- Check the depth of the water before dr iv
i ng through it.
- Do not stop the veh icle, dr ive in reverse
or switc h the engine off when driving
t hr ough water.
- Keep in mind that oncoming vehicles
may c reate waves that raise the water
l evel and make it too deep fo r you r vehi
cle to dr ive through safely.
-
- Avoid dr iving thro ugh salt water because
i t can ca use corrosion.
Catalytic converter
It is very important that your emission con
trol system (catalytic converter) is function
ing properly to ensure that your vehicle is run
ning in on environmentally sound manner.
,,. Always use lead-free gasoli ne¢ page 207,
Fuel supply .
,,. Never run the tank down a ll the way to
empty.
,,. Never put too much motor oil in your en-
gine ¢
page 217, "t':::r. Adding engine oil.
,,. Never t ry to push- o r tow-start your veh icle.
The catalytic converter is an effic ient "clean
up" device built into the exhaust system of
the vehicle. The catalytic converter burns
many of the polluta nts in the exhaust gas be
fore they are released into the atmosphe re. The exclusive
use of unleaded f uel is critica lly
important for the life of the catalytic convert
er and proper funct ion ing of the eng ine .
A WARNING
= -
-Do not park or operate the vehicle in
areas where the hot exhaust system may
come in co ntact with dry grass, brush,
fuel spill or other material wh ich can
cause a fire .
- Do not app ly additional undercoating or
r u stp roofing on or nea r the exhaust
manifold, exhaust pipes, cataly tic con
ver ter or heat shields. Dur ing driv ing, the
substance used for under coa ting co uld
overhea t and cause a fire.
CD Note
- Be aware that just o ne tank filling with
leaded fu el w ill already ser io usly de
gr ad e the per form ance o f the catalytic
c onverte r.
- Do not ex ceed t he corre ct engine oil level
r:;!) page 217.
- Do not drive until the fuel tank be co m es
completely emp ty. The engine co uld mis
fire . Unburned fuel could also get in to
the exhaust system and this co uld cause
the cata lytic converter to overheat .
- Do not turn off the igni tion whi le the ve
hicle is mov ing.
- Do not contin ue to ope rate your veh icle
unde r these conditions, as otherwise fuel
can reach the catalyt ic converte r. T his
co uld resu lt in overheating of the con
verter, requir ing its replacement.
- To assure efficient operation of the Emis
sion Control System:
- H ave you r vehicle maintained p rope rly
and in accordance w ith the se rvi ce rec
ommen dat ions in yo ur Warranty &
M ain tenance boo klet.
- L ack of prope r maintenan ce as we ll as
i mprope r use of t he ve hicl e wi ll impair
the func tion of the em ission cont ro l
system and could lea d to damage .
Ill>

Automatic car wash
The vehicle can be washed in almost any
modern automatic car wash .
The vehicle paint is so durable that the vehicle
can normally be washed without problems in
an automatic car wash. However, the effect on
the paint depends to a large extent on the de
sig n of the fac ility, the filtering of the wash
water, the type of wash and care mater ial , etc.
If the paint has a dull appearance afte r go ing
through the car wash or is scratched, bring
this to the attention of the operator immedi
ately. If necessary, use a different car wash.
The power top does not require special pre
cautions be fore passing through a car wash.
Howe ver, the c ar mu st not be tre ated with
hot w ax after th e was h cy cle !
The wax could
adversely affect the power top and
even dam
age the fabric
over a period of time.
The power top does not have to be washed
ev
ery time you use a car wash. The power top
can be spared if the car wash facility is equip
ped with manually adjustable roof brushes or
rollers .
Before going through a car wash, be sure to
take the usual precaut ions such as clos ing the
windows . Remove antenna if applicable .
If yo u have installed additional accessories on
the vehicle -such as spoilers, etc. -it is best to
ask the car wash operator if these should be
removed .
A WARNING
Always read and heed all WARNINGS and
other information
Q page 194.
(D Note
- Before washing the vehicle in an auto
matic car wash, please make sure to re
tract t he exterior m irrors to prevent
them from being damaged.
- Compare the width of your vehicle with
the width of the tunnel at the fac ility.
Cleaning and protec tion 195
Washing the vehicle by hand
A lot of water is needed when washing a vehi
cle by hand .
.,. Before you start washing, make sure you
have read and understood the WARNINGS
Q & ,
.,. First soak all dried d irt unt il it is soft, then
r inse it off.
.,. As you clean your vehicle , start w it h the
roof and work your way down to the bottom,
using a sponge, a sponge g love or a clean
brush.
.,. Rinse the sponge or the sponge g love often,
flushing it clean each time.
.,. Use specia l car shampoo only for
very per
sistent d irt .
.,. Rinse the car thoroughly w ith water .
.,. Use a chamo is leather to gently w ipe the ex-
ter ior d ry.
Use a separate sponge for cleaning the
wheels, door sills and other regions exposed
to road dirt . In this way, you will not scratch
the pa int with coarse particles imbedded in
the sponge the next time you wash the ca r.
A WARNING ~ -
- Wash your vehicle only when the ignition
is switched off to red uce the risk of a
crash.
-A lways read and heed a ll WARNINGS and
other information
Q page 194.
{(D Note
-Never try to remove dirt, mud or dust if
the surface of the veh icle is dry. Never
use a dry cloth or sponge, since this
cou ld scratch your vehicle's paint or win
dows.
- Never wash your car in bright s unlight .
Drops of water act as magnifying lenses
and may damage yo ur paint .
- When you wash your car in the winter: if
you rinse yo ur vehicle with a hose, be
careful not to aim the stream of water
directly at locks, or at door or hatch
openings -they can freeze shut . •
•

200 Cleaning and protec tio n
The best way to remove snow from windows
and mirrors is to use a brush. Use a non-abra
sive
plas tic ice scraper -better still, a spray
de icer -to remove
ic e from windows and mir
rors.
The windows must not be cleaned with insect remover or wax s ince these can interfere with
the function of the windshield wiper blades (chatter).
Oi l, grease, or silicone residue can be removed
with
gl ass clea ner or silic on e remo ver. How
ever, wax residue requires the use of a special ly formulated solvent. Please contact your au
thor ized Audi dealer for adv ice on safe prod
ucts for wax removal.
W indows shou ld also be cleaned on the inside
at regular intervals.
Never dry windows with the same chamois
that you use to dry painted surfaces. Wax resi
due on the chamois can impair vision through
the w indows.
.&_ WARNING
- Always read and heed all WARNINGS and
other information ~
page 194.
-The windshie ld must not be treated with
water-repellent materials . They can in
crease glare under poor visib ility condi
tions such as wetness, darkness, or when
the sun is low on the hori zon. In addi
t ion, they can cause the win dshield wip
ers to chatter.
(D Note
- Never use warm or hot water to remove
snow and ice from windows and mirrors.
This cou ld cause the g lass to cra ck.
- To preven t damage to the wi res of the
rear defogger, do not place any adhe sive
stickers on the inside of the rear window
ove r the wires .
- To he lp prevent d irt from sc ratch ing the
window, always scrape in a forward di
rection -pushing the scraper away from
you -never back and fo rth. -
Water leaking from the ins ide of the rear
windows may damage sensitive electrical components located either under the
rear parcel shelf or in the rear trunk area.
Always ensure that water never leaks
through the body section of the vehicle.
You can do th is by us ing waterproof pro
tection over the vehicle's electrical com
ponents (e.g. when install ing window
tinting) .
- Damage or malfunction of elect rical
c ompone nts due to water damage or any
other o uts ide infl uence is not covered by
the A udi New Veh icle Limited Warranty.
See your Warranty
& Ma intenance book
let for additional detai ls about your war
ranty.
Cast (light) alloy wheels
Cast (light) alloy wheels require special care.
.,. Wash the w heels with a sponge or hose
brush every other week .
.,. For deep clean ing afterwards, use only a
dedicated
a ci d-free cast alloy wheel cleaner.
.,. Rub a coat of
liqu id w ax onto the rims every
three month. Be sure to reach and treat all
parts of the rim.
To preserve the decorative appearance of the cast alloy wheels, some special care is neces
sary. In addition to road dirt and salt, brake dust is also corrosive . If left on for too long,
brake dust can cause pitting .
U se only spec ial
acid-free cleaners formulated
for alloy r ims. Safe products are availab le at
your authorized Aud i dealer . Never leave the
cleaner on the rims longer than spec ified on
the label. If not rinsed off promptly, the acid
contained in some cleane rs can attac k the
threads on the wheel bolts .
Never use abrasive o r metal po lish ing clean
ing agents.
If the protective coating has been
c h ipped, e .g. by kicked up road dirt, touc h it
u p as soon as possible . .,..

A WARNING 1=
- Moisture and ice on brakes may affect
braking efficiency
Q page 181 . Test the
brakes carefully each time you wash the
vehicle .
- Always read and heed all WARNINGS and other information Qpage 194.
Body cavity sealing
The body cavity sealing does no t need to be
checked.
All body cavities which co uld be affected by
corrosion have been thoro ughly protec ted at
the factory.
This sea ling does not require any inspection or
addit iona l treatment. If any wax should seep
out of the cav ity when the ambient tempera
ture is high, it can be removed w it h a plastic
scraper and a suitab le solvent.
A WARNING
So lvents can be dangerous .
- Benzine is flammable and toxic . If you
use benzine for removing the wax, keep
spar ks , flame and light ed c igaret tes
away. Never dump ben zine on t he
ground, in to open s tre ams or dow n sew
age dra ins.
- Be sure to observe all safety and env iro n
me ntal regu lations. Follow all ins truc
t ions on the con tainer .
- Always re ad and hee d all WARN INGS and
ot her informa tion
Q page 194 .
Chassis
Have the undercoating checked for damage
from time to time.
The lower body shell of your Audi is a lso thor
ough ly protected against corrosion .
Any damage to the undercoating caused by road hazards shou ld be repa ired promptly .
Cleaning and protec tion 20 1
A WARNING
Too much undercoating i n the wrong p la
ces can cause a fire .
- Do not apply additional undercoating or
ru stp roof ing o n or near the exhaust
manifold, exhaust pipes, catalytic con
verter or heat shields . While d riving, the
substance used fo r under coating could
over hea t an d cause a fire.
- Always read an d heed a ll WAR NIN GS and
o ther info rmation
c:? page 19 4.
Exhaust tail pipes
Road salt and other co rrosive mater ials w ill
d amage the mate rial in the exhaus t tail pipes
i f they are not cleaned regular ly . Do not clea n
the tail pipes with whee l cleaner, paint polish,
c hr ome polish or other abras ive cleaners .
Clean the tail pipes with car care products
that are suitable for sta inless s teel.
Your a uthorized Audi dea ler can provi de clean
ing products that have been tested and ap
proved for yo ur vehicle.
Care of interior
Infotainment components
The Rad io/MM !* disp lay m ay be cleaned with
a soft cloth and commercially-available "LC D
cleaner". The cloth should be coated lightly
whe n the cleaning sol ution when cleaning the
display.
T he M MI* con trols m ust be cleaned first with
a b rush so that dirt does not enter the unit or
enter between the buttons and the housing.
Then wiping the cont rols with a cloth damp
ened with dish de tergent and water is recom
mended .
(D Note
-To avoid scratching the display, you
should never clean it dry .
- To prevent damage, make sure fluids do
not enter the cont ro ls .
•
•