2013.5 Citroen DS5 engine

Manual operation




Select position M
for sequential
changing
of the six gears.


Push the lever towards the +
sign to
change up a gear.


Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to
another if the vehicle speed and engine speed
permit; other wise, the gearbox will operate
temporarily in automatic mode.

D
disappears and the gears engaged
appear in succession on the
instrument panel.
If the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D

(automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving
very slowly, the gearbox selects gear 1

automatically.
The sport and snow programmes do not
operate in manual mode.

Sport and snow programmes


Sport programme "S"




Press button "S"
, after starting the engine.
The gearbox automatically favours a dynamic
style of driving.

S
appears in the instrument panel.


Snow programme " 
"




Press button " 
", after starting the engine.
The gearbox adapts to driving on slippery
roads.
This programme improves starting and drive
when traction is poor.


appears in the instrument panel.



Return to automatic
operation



At any time, press the button selected
again to quit the programme engaged and
return to auto-adaptive mode.
These two special programmes supplement the
automatic operation in very specific conditions
of use.

11 9Driving

Invalid value during manual
operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, put the lever in
position P
or N
to place the gearbox in neutral.
In both cases, apply the parking brake to
immobilise the vehicle, unless it is programmed
to automatic mode.

If the lever is not in position P
, when the
driver's door is opened or approximately
45 seconds after the ignition is switched
off, there is an audible signal and a
message appears.



Return the lever to position P
;
the audible signal stops and the
message disappears.




Operating fault

When the ignition is on, a message appears
in the instrument panel screen to indicate a
gearbox fault.
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from P

to R
and from N
to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (100 km/h), local speed
restrictions permitting.
Have it checked by a CITROËN dealer or a
qualified workshop.
You risk damaging the gearbox:


- if you press the accelerator and
brake pedals at the same time,

- if you force the lever from position P

to another position when the
battery is flat.
To reduce fuel consumption when
stationary for long periods with the
engine running (traffic jam...), position
the gear lever at N
and apply the
parking brake, unless it is programmed
in automatic mode.

121Driving

Engagement of reverse gear is
accompanied by an audible signal.

If the engine does not start:


- If N
is flashing in the instrument
panel, move the gear lever to
position A
then to position N
.

- If the message "foot on the brake"
is displayed, press the brake pedal
firmly.

When the engine is idling with the
brakes off, if position R
, A
or M
is
selected, the vehicle will move off
on its own without any action on the
accelerator.



Displays in the instrument panel

When you move the lever, the symbol
corresponding to its position is displayed in the
instrument panel.


N
Neutral

R
Reverse

1, 2, 3, 4, 5, 6
Gears in manual mode

AUTO
This comes on when the automated
mode is selected. It switches off on
changing to manual mode.

S
Sport (Sport setting).




If the message " foot on the
brake
" is displayed in the
instrument panel, press the
brake pedal firmly.



Moving off




To start the engine, place the gear lever in
position N
.


Press the brake pedal down fully.


Start the engine.



Select a mode (position M
or A
) or reverse
(position R
).


Release the parking brake unless it is
programmed to automatic mode.


Take your foot off the brake pedal, then
accelerate.

A
UTO and 1
or R
appear in the
instrument panel screen.

Automatic mode




After starting the vehicle, select position A

for enter automatic mode.

A
UTO
and the gear engaged appear
in the instrument panel screen.
The gearbox is then operating in auto-active
mode, without any action on the part of the
driver. It continuously selects the most suitable
gear, depending on the:


- style of driving,

- profile of the road.

For optimum acceleration, for example
when overtaking another vehicle, press
the accelerator pedal firmly past the
point of resistance.

Manual gear changing




When the vehicle has moved off, select
position M
to change to manual mode.


Operate the +
or -
steering mounted control
paddles.

A
UTO
disappears and the gears
engaged appear successively in the
instrument panel screen. The gear change requests are only carried out
if the engine speed permits.
It is not necessary to release the accelerator
during gear changes.
When braking or slowing down, the gearbox
changes down automatically to permit
acceleration in the correct gear.
This selective gear change mode enables you
to overtake, for example, while still remaining in
automatic mode.



Operate the +
or -
steering mounted control
paddle.
The gearbox engages the gear requested if the
engine speed permits. AUTO
is still displayed
in the instrument panel.
After a few moments without any action on
the controls, the gearbox resumes automatic
control of the gears.



Manual mode


At very low speed, if reverse gear is
requested, this will only be taken into
account when the vehicle is immobilised
(foot on the brake). A warning lamp
appears in the instrument panel screen.

On sharp acceleration in manual mode,
the gearbox will not change up unless
the driver acts on the gear lever or the
steering mounted paddles.
Never select neutral N
while the vehicle
is moving.
Only engage reverse gear R
when the
vehicle is immobilised with the brake
pedal pressed.

123Driving

You must press the brake pedal when
starting the engine.
Whatever the circumstances, you must
manually apply the parking brake when
parking, unless the parking brake is
programmed in automatic mode.

When immobilising the vehicle, with
the engine running, you must place the
gear lever in neutral N
.
Before carrying out any work in the
engine compartment, check that the
gear lever is in neutral N
and that the
parking brake is applied.



Stopping the vehicle

With the ignition on, the
flashing of this warning lamp,
accompanied by an audible
signal and a message
in the instrument panel screen, indicates a
malfunction of the gearbox.
Have it checked by CITROËN or a qualified
workshop. Before switching off the engine, you can
choose to:


- move to position N
to engage neutral,

- leave the gear engaged; in this case, it will
not be possible to move the vehicle.
In both cases, you should apply the parking
brake to immobilise the vehicle.

Operating fault

Sport setting




After selection of manual or
automated mode, press the
S
button to switch on the Sport
setting, which provides a more
dynamic driving style.
S
appears alongside the gear
engaged in the instrument panel
screen.


Press the S
button again to switch it off.
S
then disappears from the instrument
panel screen.
The Sport setting is switched off every time the
ignition is switched off.

127Driving














Stop & Start


Operation


Going into engine STOP mode

The "ECO"
warning lamp comes on
in the instrument panel and the engine
goes into standby automatically:


- with a manual gearbox
, at speeds below
12 mph (20 km/h) or vehicle stationary with
the Blue HDi 120 version, when you place
the gear lever in neutral, and you release
the clutch pedal,

- with an electronic gearbox
, at speeds
below 5 mph (8 km/h), when you press
the brake pedal or put the gear lever in
position N
,

- with an automatic gearbox
, vehicle
stationary, when you press the brake pedal
or put the gear lever in position N
. If your vehicle is fitted with the system, a time
counter calculates the sum of the periods in
STOP mode during a journey. It resets itself to
zero every time the ignition is switched on with
the START/STOP button.

Never refuel with the engine in STOP
mode; you must switch off the ignition
with the START/STOP button.
For your comfort, during parking
maoeuvres, STOP mode is not
available for a few seconds after
coming out of reverse gear.
STOP mode does not affect the
functionality of the vehicle, such as for
example, braking, power steering...


Special cases: STOP mode not
available
STOP mode is not invoked when:


- the vehicle is on a steep slop (rising or
falling),

- the driver's door is open,

- the driver's seat belt is not fastened,

- the vehicle has not exceeded 6 mph
(10 km/h) since the last engine start using
the START/STOP button,

- the electric parking brake is applied or
being applied,

- the engine is needed to maintain a
comfortable temperature in the passenger
compartment,

- demisting is active,

- some special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.
In this case, the "ECO"
warning lamp
flashes for a few seconds then goes
off. The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...).
The engine restarts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Start system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.

This operation is per fectly normal.

Going into engine START mode

The "ECO"
warning lamp goes off
and the engine starts automatically:


- with a manual gearbox
, when you fully

depress the clutch pedal,

- with an electronic gearbox
:


●
gear lever in position A
or M
, when you
release the brake pedal,

●
or gear lever in position N
and brake
pedal released, when you place the gear
lever in position A
or M
,

●
or when you engage reverse.

- with an automatic gearbox
:


●
gear lever in position D
or M
, when you
release the brake pedal,

●
or gear lever in position N
and brake
pedal released, when you place the gear
lever in position D
or M
,

●
or when you engage reverse.

START mode is invoked automatically when:


- the driver's door is open,

- the driver's seat belt is not fastened,

- the speed of the vehicle exceeds 15 mph
(25 km/h) with a manual gearbox (2 mph
(3 km/h) with the Blue HDi 120 version),
7 mph (11 km/h) with an electronic gearbox
and 2 mph (3 km/h) with an automatic
gearbox.

- the electric parking brake is being applied,

- some special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system.


Special cases: START invoked
automatically

If the system has been deactivated
in STOP mode, the engine restarts
immediately.
At any time, press the "ECO OFF"
switch to
deactivate the system.
This is confirmed by the switch warning lamp
coming on accompanied by a message in the
screen.

Deactivation

In this case the "ECO"
warning lamp
flashes for a few seconds, then goes
off.

This operation is per fectly normal.

129Driving

The system is reactivated automatically
at every new start using the START/
STOP button.



Reactivation

Press the "ECO OFF"
switch again.
The system is active again; this is confirmed
by the switch warning lamp going off and a
message in the screen.

Operating fault

In the event of a fault with the system, the
"ECO OFF"
switch warning lamp flashes then
comes on continuously.
Have it checked by a CITROËN dealer or a
qualified workshop.
In the event of a fault in STOP mode, the vehicle
may stall.
All of the instrument panel warning lamps come
on.
Depending on version, an alert message may also
be displayed, asking you to place the gear lever in
position N
and put your foot on the brake pedal.
It is then necessary to switch off the ignition and
start the engine again using the "START/STOP"
button.
Before doing anything under the
bonnet, deactivate the Stop & Start
system to avoid any risk of injury
resulting from automatic operation of
START mode.
This system requires a 12 V battery with a
special specification and technology (reference
numbers available from CITROËN dealers).
Fitting a battery not listed by CITROËN
introduces the risk of malfunction of the
system.
For charging, use a 12 V charger and do not
reverse the polarity.

Maintenance


The Stop & Start system makes use of
advanced technology. For any work on
the system go to a qualified workshop
with the skills and equipment required,
which a CITROËN dealer is able to
provide.