2013.5 Citroen DS5 ignition

41Monitoring


Warning / indicator lamp



State



Cause



Action / Observations









Airbags


on temporarily. This lamp comes on for a few
seconds when you turn on the
ignition, then goes off. This lamp should go off when the engine is started.
If it does not go off, contact a CITROËN dealer or a
qualified workshop.

fixed. One of the airbag or seat belt
pretensioner systems has a fault. Have it checked by a CITROËN dealer or a qualified
workshop.






Directional
headlamps


flashing. The directional headlamps system
has a fault. Have it checked by a CITROËN dealer or a qualified
workshop.






Seat belt(s)
not fastened /
unfastened


fixed
or flashing
accompanied by an
audible signal. A seat belt has not been fastened or
has been unfastened. Pull the strap then insert the tongue in the buckle.

43Monitoring






Service indicator


More than 1 800 miles (3 000 km)
remain before the next service is due
When the ignition is switched on, no ser vice
information appears in the screen. System which informs the driver when the
next ser vice is due, in accordance with the
manufacturer's ser vicing schedule.
The point at which the ser vice is due is
calculated from the last indicator zero reset. It
is determined by two parameters:


- the distance travelled,

- the time elapsed since the last ser vice.


Between 600 miles (1 000 km)
and 1 800 miles (3 000 km) remain
before the next service is due
For 5 seconds after the ignition is switched on, the
spanner symbolising the ser vice operations comes
on. The distance recorder display line indicates the
distance remaining before the next ser vice is due.

Example:
1 700 miles (2 800 km) remain
before the next ser vice is due.
For 5 seconds after the ignition is switched on,
the screen indicates:
5 seconds after the ignition is switched on,
the spanner goes off
; the distance recorder
resumes its normal operation. The screen then
indicates the total and trip distances.


Less than 600 miles (1 000 km)
remain before the next service is due

Example:
560 miles (900 km) remain before
the next ser vice is due.
For 5 seconds after the ignition is switched on,
the screen indicates:
5 seconds after the ignition is switched on,
the distance recorder resumes its normal
operation. The spanner remains on
to
indicate that a ser vice must be carried out
soon.

Illumination of the key is accompanied
by a message in the instrument panel
screen.

Service overdue

For 5 seconds after the ignition is switched on,
the spanner flashes
to indicate that the ser vice
must be carried out as soon as possible.

Example:
the ser vice is overdue by 186 miles
(300 km).
For 5 seconds after the ignition is switched on,
the screen indicates:
With Blue HDi Diesel versions, the
Service
warning lamp also comes on
when the ignition is switched on.
The distance remaining may be
weighted by the time factor, depending
on the driving conditions.
Therefore, the spanner may also come
on if you have exceeded the period
since the last ser vice, indicated in the
maintenance and warranty guide.
Following this operation, if you wish to
disconnect the battery, lock the vehicle
and wait at least five minutes for the
zero reset to be taken into account. 5 seconds after the ignition is switched on,
the distance recorder resumes its normal
operation. The spanner remains on
.








Service indicator zero reset

After each ser vice, the ser vice indicator must
be reset to zero.
The procedure for resetting to zero is as
follows:



switch off the ignition,


press and hold the trip distance recorder
zero reset button,


switch on the ignition; the distance recorder
display begins a countdown,


when the display indicates "=0"
, release
the button; the spanner disappears.


Retrieving the service
information
You can access the ser vice information at any
time.



Press the trip distance recorder zero reset
button.
The ser vice information is displayed for a few
seconds, then disappears.

System for manual adjustment of the
brightness of the instruments and controls in
relation to the exterior brightness.









Lighting dimmer


Activation

When the lighting is on:



press the button to change the brightness
of the instruments and controls,


when the level of brightness required is
reached, release the button.



Deactivation

When the lighting is off, or in day mode on
vehicles fitted with daytime running lamps,
pressing the button does not have any effect.
The total and trip distances are displayed for thirty seconds when the ignition is switched off, when
the driver's door is opened and when the vehicle is locked or unlocked.












Distance recorders


Total distance recorder

System which measures the total distance
travelled by the vehicle since its first
registration.

To conform to legislation in the country
you are crossing, change the units
of distance (miles or km) via the
configuration menu.


Trip distance recorder

System which measures a distance travelled
during a day or other period since it was reset
to zero by the driver.



With the ignition on, press the button until
zeros appear.

Clock

The analogue clock does not have an
adjustment button.
To set the time, refer to the section relating to
the screen (audio system) configuration menu.
The clock is synchronised with the screen time;
once the the setting has been confirmed in
the screen, the hands will turn to synchronise
with the screen, and each time the ignition is
switched on.

Setting the date and time






















Audio system / Bluetooth


Press MENU
.



Using the arrows, select " Personalisation-
configuration
" and confirm.
Using the arrows, select " Display
configuration
" and confirm.

Using the arrows, select " Date and time
adjustment
" and confirm.

Select the setting to be modified. Confirm
by pressing OK
, then make the change and
confirm again to save the modification.

Adjust the settings one by one, confirming by
pressing the OK
button. Next select the " OK
"
tab on the screen then confirm to exit from the
" Date and time adjustment
" menu.

49Monitoring




















eMyWay


Select " Synchronize the minutes
with GPS
" so that setting the minutes
is done automatically by satellite
reception.








The clock, located in the dashboard,
is synchronised with the time in the
screen. It is set once the time is
adjusted using the " SETUP
" menu and
every time the ignition is switched on.

Press SETUP
to display the " Configuration
"
menu.
Select " Display configuration
" and confirm.

Select " Set date and time
" and confirm.

Select the setting to adjust.
Confirm by pressing OK
, then adjust the setting
and confirm again to save the modification.

Adjust the settings one by one.
Then select " OK
" on the screen and confirm to
save the settings.

51Monitoring
If dashes are displayed continuously
while driving in place of the digits,
contact a CITROËN dealer or a
qualified workshop. This value may vary following a change
in the style of driving or the relief,
resulting in a significant change in the
current fuel consumption.






Trip computer, a few definitions…


Range

(miles or km)
This indicates the distance
which can still be travelled with
the fuel remaining in the tank
in relation to the average fuel
consumption over the last few
miles (kilometres) travelled.
When the range falls below 20 miles (30 km),
dashes are displayed. After filling with at least
5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (100 km). This function is only displayed from
20 mph (30 km/h).


Current fuel consumption

(mpg or l/100 km or km/l)
This is the average fuel consumption
during the last few seconds.

Average fuel
consumption
(mpg or l/100 km or km/l)
This is the average fuel
consumption since the last trip
computer zero reset.


Average speed

(mph or km/h)
This is the average speed calculated
since the last trip computer zero
reset (ignition on).









Stop & Start time
counter
(minutes / seconds or hours /
minutes)
If your vehicle is fitted with Stop & Start, a time
counter calculates the time spent in STOP
mode during a journey.
It resets to zero every time the ignition is
switched on with the START/STOP button.

57Access













Locking the vehicle





With the electronic key in the recognition
zone A
, press with a finger on one of the
door handles (at the markings) to lock the
vehicle
.
Maintain pressure with your finger until the
windows close completely.


Locking is confirmed by fixed
lighting of the direction indicators for
approximately two seconds.
The door mirrors fold at the same time.
















If one of the doors or the boot is still
open or if the key for Keyless Entry and
Starting system has been left inside
the vehicle or if the ignition is on, the
central locking does not take place.
When the vehicle is locked, if it is
unlocked inadvertently, it will lock itself
again automatically after about thirty
seconds unless a door is opened.
If the alarm was previously activated, it
will not be reactivated automatically.
The folding and unfolding of the door
mirrors by the remote control can be
deactivated by a CITROËN dealer or a
qualified workshop.
As a safety measure (children on
board), never leave the vehicle without
taking the key for the Keyless Entry and
Star ting system, even for a shor t period.
Guard against theft when the key for the
Keyless Entry and Starting system is
in the recognition zone with the vehicle
unlocked.
In order to preser ve the charge of the
cell battery in the remote control, the
"hands-free" functions go into extended
stand-by after 21 days of non-use. To
restore these functions, press one of
the remote control buttons or start the
engine with the electronic key in the
reader.

Ensure that no one prevents the correct
operation of the windows.
Be aware of children when operating
the windows.
This function allows you to identify
your vehicle from a distance,
particularly in poor light. Your vehicle
must be locked.






Locating your vehicle




Press the closed padlock on the remote
control.
This will switch on the courtesy lamps and
the direction indicators will flash for around
ten seconds.