2013.5 Citroen DS4 RHD battery

CHECKS PRACTICAL
INFORMATIONTECHNICAL DATA AUDIO AND
TELEMATICS
235 Bonnet
236 Running out of fuel (Diesel)
237 Petrol engines
238 Diesel engines
239 Checking levels
242 Checks248 Temporary puncture repair
kit
253 Changing a wheel
260 Snow chains
261 Changing a bulb
268 Changing a fuse
274 12 V battery
278 Energy economy mode
279 Changing a wiper blade
279 Very cold climate screen
280 Fitting roof bars
281 Towing the vehicle
283 Towing a trailer
285 Accessories290 Petrol engines
291 Petrol weights
292 Diesel engines
293 Diesel weights
294 Dimensions
295 Identifi cation markings299 Emergency or assistance
301 eMyWay
355 Audio system
012012013013010010011011

45Monitoring


Warning lamp



is on



Cause



Action/Observations






Battery charge


fixed. The battery charging circuit has a fault
(dirty or loose terminals, slack or cut
alternator belt, ...). The warning lamp should go off when the engine is
started.
If it does not go off, contact a CITROËN dealer or a
qualified workshop.




Braking


fixed, associated with
the STOP warning
lamp. The braking system fluid level has
dropped significantly. You must stop as soon as it is safe to do so.
Top up with brake fluid recommended by CITROËN.
If the problem persists, have the system checked by a
CITROËN dealer or a qualified workshop.

+
fixed, associated with
the electric parking
brake malfunction
warning lamp, if the
parking brake is
released. The braking system has a fault. You must stop as soon as it is safe to do so.
Park, switch off the ignition and contact a CITROËN
dealer or a qualified workshop.

+
fixed, associated with
the STOP and ABS
warning lamps. The electronic brake force distribution
(EBFD) system has a fault. You must stop as soon as it is safe to do so.
Have it checked by a CITROËN dealer or a qualified
workshop.

47Monitoring




Service


temporarily,
accompanied by a
message. A minor malfunction has occurred for
which there is no specific warning
lamp. Identify the malfunction by reading the message
displayed in the screen, such as, for example:


- the opening of the doors, boot or bonnet,

- the engine oil level,

- the remote control battery,

- the tyre pressures,

- saturation of the particle emission filter on
Diesel vehicles (see "Checks - § Checks/Particle
emissions filter").
For any other malfunctions, contact a CITROËN dealer
or a qualified workshop.

fixed, accompanied
by a message and an
audible signal. A major malfunction has occurred
for which there is no specific warning
lamp. Identify the malfunction by reading the message
displayed in the screen and contact a CITROËN dealer
or a qualified workshop.

Warning lamp



is on



Cause



Action/Observations



Particle
emissions filter
(Diesel)
fixed, accompanied
by an audible signal
message on the risk of
blockage of the particle
emissions filter. This indicates that the particle
emissions filter is starting to become
saturated. As soon as driving conditions allow, regenerate the
filter by driving at a speed of at least 35 mph (60 km/h)
until the warning lamp goes off.
fixed, accompanied by
an audible signal and
and a message that the
particle emissions filter
additive level is too low.

This indicates the low level of the
additive reservoir. Have the reser voir topped up as soon as possible by a
CITROËN dealer or a qualified workshop.

A few seconds after the ignition is switched
on, the distance recorder resumes its normal
operation. The spanner remains on
.
The distance remaining may be
weighted by the time factor, depending
on the type of driving.
Therefore, the spanner may also come
on if you have exceeded the two year
service interval.









Service indicator zero reset

After each ser vice, the ser vice indicator must
be reset to zero.
The procedure for resetting to zero is as
follows:



switch off the ignition,


press and hold the ".../000"
trip distance
recorder zero reset button,


switch on the ignition; the distance recorder
display begins a countdown,


when the screen indicates "=/0"
and the
spanner disappears, release the button. This operation cannot be carried
out while a reminder of the ser vicing
information is being displayed.
Following this operation, if you wish to
disconnect the battery, lock the vehicle
and wait at least five minutes for the
zero reset to be registered.


Recalling the service information

You can recall the ser vice information at any
time.



Briefly press the ".../000"
trip distance
recorder zero reset button.
The ser vice information is displayed for a
few seconds, in the total distance recorder
line or in the type 2 instrument panel
central screen.




Service overdue

For a few seconds after the ignition is switched on,
the spanner flashes
to indicate that the ser vice
must be carried out as soon as possible.

Example:
the ser vice is overdue by 180 miles
(300 km).
For a few seconds after the ignition is switched on,
the screen indicates:

5. Air conditioning On / Off




Press this button to switch off
the air conditioning.
Switching the system off could result in
discomfort (humidity, condensation).



Press this button again to return to
automatic operation of the air conditioning.
The indicator lamp on the "A /C "
button
comes on.



6. Air distribution adjustment




Press one or more buttons to
direct the air flow towards:


- the windscreen and side windows
(demisting or defrosting),

- the outer and centre air vents,

- the footwells.

You can combine the three orientations to
obtain the desired air distribution.


7. Air fl ow adjustment




Turn this control to the left to
decrease the air flow or to the
right to increase the air flow.


8. Air intake / Air recirculation




Press this button for
recirculation of the interior
air. The indicator lamp in the
button comes on. The air flow indicator lamps, between the two
fans, come on progressively in relation to the
value requested.


9. "REST" function: ventilation
with the engine off
Even with the engine is off, you can
operate the ventilation for a few
minutes.
Air recirculation enables the passenger
compartment to be isolated from exterior
odours and smoke.



As soon as possible, press this button
again to permit the intake of outside air and
prevent the formation of condensation. The
indicator lamp in the button goes off.
For example, while you are away from the
vehicle, the passengers can still enjoy some air
circulation without having the engine running.
This function is available after switching on the
ignition, as well as after stopping the engine.
The period that the function is available
depends on the state of charge of the battery.
You can activate the "REST" function while the
air conditioning control screens are on.

Avoid prolonged operation in interior air
recirculation mode (risk of misting and
deterioration of air quality).

In the event of a malfunction with the remote
control, you can no longer unlock, lock or
locate your vehicle.



First of all, use the key in the lock to unlock
or lock your vehicle.


Then, reinitialise the remote control.
















Fault with the remote
control

Reinitialisation




Switch off the ignition and remove the
ignition key.


Press the closed padlock immediately for a
few seconds.


Turn the key to position 2 (Ignition on)
.


Switch off the ignition and remove the key
from the ignition switch.
The remote control is fully operational again.


Changing the battery

Battery ref.: CR2032/3 volts.


Unclip the cover using a small screwdriver
at the two cutouts.


Lift off the cover.


Remove the flat battery from its location.


Fit the new battery into its location
obser ving the original direction of fitment.


Clip the cover onto the casing.
If the battery is flat, you are
informed by illumination of this
warning lamp, an audible signal
and a message in the screen.

If the problem persists, contact a
CITROËN dealer as soon as possible.

Alarm *
System which protects and provides a deterrent against theft and break-ins. It provides the following types of monitoring.


- exterior perimeter

The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot, the bonnet...




- interior volumetric

The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compartment or
moves inside the vehicle.




Locking the vehicle with full
alarm system

- tilt

The system checks for any change in the
attitude of the vehicle.
The alarm is triggered if the vehicle is lifted,
moved or knocked.




Self-protection function

The system checks for the putting out of
ser vice of its components.
The alarm is triggered if the battery, the central
control or the siren wiring are put out of service
or damaged.
For all work on the alarm system,
contact a CITROËN dealer or a
qualified workshop.


Activation




Switch off the ignition and get out of the vehicle.


Press the locking button on the remote control.
The monitoring system is active: the indicator
lamp in the button flashes once per second.
After the locking button on the remote control
is pressed, the exterior perimeter monitoring
is activated after a delay of 5 seconds and the
interior volumetric and anti-tilt monitoring after
a delay of 45 seconds.

Deactivation




Press the unlocking button on the remote
control.
The alarm system is deactivated: the indicator
lamp in the button goes off.
If an opening (door, boot...) is not
closed fully, the vehicle is not locked
but the exterior perimeter monitoring
will be activated after a delay of
45 seconds at the same time as
the interior volumetric and anti-tilt
monitoring.

*
According to country.

System allowing the doors to be locked and
unlocked manually in the event of a malfunction
of the central locking system or battery failure.






Emergency control


Locking the driver's door




Insert the key in the door lock, then turn it
to the rear.
You can also apply the procedure described for
the passenger doors.


Unlocking the driver's door




Insert the key in the door lock, then turn it
to the front.



Locking the front and rear
passenger doors



Open the doors.


On the rear doors, check that the child lock
is not on (see the corresponding section).


Remove the black cap, located on the edge
of the door, using the key.


Insert the key in the socket without forcing
it, then without turning it, move the latch
sideways towards the inside of the door.


Remove the key and refit the cap.


Close the doors and check that the vehicle
has locked correctly from the outside.



Unlocking the front and rear
passenger doors



Pull the interior door opening control.