2012 YAMAHA XT660Z check oil

1
2
3
4
5
6
7
8
9
10
PERIODIC M\fINTEN\fNCE \fND \fDJ\bSTMENT
7-23
EAU22731
Changing the brake fluid
Have a Yamaha dealer \fhange the
\brake fluid at the intervals spe\fified in
the TIP after the periodi\f maintenan\fe
and lu\bri\fation \fhart. In addition, have
the oil seals of the master \fylinders
and \falipers as well as the \brake
hoses repla\fed at the intervals listed
\below or whenever they are damaged
or leaking.
●Oil seals: Repla\fe ever y two
years.
●Brake hoses: Repla\fe every four
years.
EAU22760
Drive chain slack
The drive \fhain sla\fk should \be
\fhe\fked \before ea\fh ride and adjusted
if ne\fessary.
EAU22783
To check the drive chain slack
1. Drive \fhain sla\fk
1. Pla\fe the motor\fy\fle on the side-stand.
TIP
When \fhe\fking and adjusting the dri-
ve \fhain sla\fk, there should \be no
weight on the motor\fy\fl\re.
2. Shift the transmission into theneutral position.
3. Move the rear wheel \by pushing the motor\fy\fle to lo\fate the tight-
est portion of the drive \fhain, and
then measure the drive \fhain
sla\fk as shown.
4. If the drive \fhain sla\fk is in\for- re\ft, adjust it as follows.
TIP
When \fhe\fking the drive \fhain sla\fk,
the \fhain tensioner should not \be
tou\fhing the drive \fhain.
Drive chain slack:50.0-60.0 mm (1.96\r-2.36 in)
XT660Z 05-07 ING-AUS:MY03 04-06 ING 11-05-2009 10:10 Pagina 7-23

1
2
3
4
5
6
7
8
9
10
PERIODIC M\fINTEN\fNCE \fND \fDJ\bSTMENT
7-25
EAU23023
Cleaning and lubricating
the drive chain
The drive chai\f mus\b be clea\fed a\fd
lubrica\bed a\b \bhe i\f\bervals specified i\f
\bhe periodic mai\f\be\fa\fce a\fd lubrica-
\bio\f char\b, o\bherwise i\b will quickly
wear ou\b, especially whe\f ridi\fg i\f
dus\by or we\b areas. Service \bhe drive
chai\f as follows.
ECA10581
NOTICE
The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.\M
1. Clea\f \bhe drive chai\f wi\bh kerose\fe a\fd a small sof\b brush. NOTICE:
To prevent damaging the O-
rings, do not clean the drive
chain with steam cleaners,
high-pressure washers or inap-
propriate solvents. 2. Wipe \bhe drive chai\f dry.
3. Thoroughly lubrica\be \bhe drive
chai\f wi\bh a special O-ri\fg chai\f
lubrica\f\b. NOTICE: Do not use
engine oil or any other lubri-
cants for the drive chain, as
they may contain substances
that could damage the O-rings.
EAU23101
Checking and lubricating
the cables
The opera\bio\f of all co\f\brol cables a\fd
\bhe co\fdi\bio\f of \bhe cables should be
checked before each ride, a\fd \bhe ca-
bles a\fd cable e\fds should be lubri-
ca\bed if \fecessary. If a cable is dam-
aged or does \fo\b move smoo\bhly, have
a Yamaha dealer check or replace i\b.
W\fRNING! Damage to the outer
sheath may interfere with proper
cable operation and will cause the
inner cable to rust. Replace a dam-
aged cable as soon as possible to
prevent unsafe condit\Mions.
Recommended lubrican\Mt: E\fgi\fe oil
XT660Z 05-07 ING-AUS:MY03 04-06 ING 11-05-2009 10:10 Pagina 7-25

PERIODIC MAINTENANCE AND ADJUSTMENT
7-28
1
2
3
4
\f
6
7
8
\b
10
EAU23272
Checking the front fork
The condition and o\feration of the
front fork \bust be checked as follows
at the inter vals s\fecified in the
\feriodic \baintenance and lubrication
chart.
To check the condition
Check the inner tubes for scratches,
da\bage and excessive oil leakage.
To check the operation 1. Place the \botorcycle on a level surface and hold it in an u\fright
\fosition. WARNING! To avoid in-
jury, securely support the vehi-
cle so there is no danger of it
falling over.
2. While a\f\flying the front brake, \fush down hard on the handle-
bars several ti\bes to check if the
front fork co\b\fresses and re-
bounds s\boothly.
ECA10590
NOTICE
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.
EAUM1650
Lubricating the swingarm
pivots
The swingar\b \fivots \bust be lubricat-
ed at the intervals s\fecified in the \fe-
riodic \baintenance and lubrication
chart.
Recommended lubric\4ant: Lithiu\b-soa\f-based g\arease
XT660Z 05-07 ING-AUS:MY03 04-06 ING 11-05-2009 10:10 Pagina 7-28

1
2
3
4
5
6
7
8
9
10
MOTORCYCLE C\fRE \fND STOR\f\bE
8-4
Long-term
Before storing your motorcycle for se\f-
eral months:\b. Follow all the instructions in the “Care” section of this ch\lapter.
2. Fill up the fuel tank and add fuel stabilizer (if a\failable) to pre\fent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to protect the cylinder, piston rings,
etc. from corrosion.a. Remo\fe the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes
are grounded. (This will limit
sparking during the next step.)
d. Turn the engine o\fer se\feral times with the starter. (This will
coat the cylinder wall with oil.)
e. Remo\fe the spark plug cap from the spark plug, and then
install the spark plug and the
spark plug cap. W\fRNIN\b! To prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
4. Lubricate all control cables and the pi\foting points of all le\fers
and pedals as well as of the side-
stand/centerstand.\l
5. Check and, if necessary, correct the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alter-
nati\fely, turn the wheels a little
e\fery month in order to pre\fent
the tires from becoming degraded
in one spot.
6. Co\fer the muffler outlets with plastic bags to pre\fent moisture
from entering them. 7. Remo\fe the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessi\fely cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the batter y, see
page 7-3\b.
TIP
Make any necessary repairs before
storing the motorcycle.
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 5

1
2
3
4
5
6
7
8
9
10
INDEX
AAftermarket Parts, Accessories, and Modifications ...................................\f\.-4
Aftermarket Tires and \bims ...............\f-4
Air filter element, cleaning the check hose ....................................\...........7-14
Air filter element, replacing ..............7-14
Auxiliary light bulb, replacing............7-35
Avoid Carbon Monoxide poisoning ....\f-\f
B Battery ....................................\...........7-30 To access the battery ...................7-30
To charge the battery....................7-30
To store the battery.......................7-31
Be a \besponsible Owner ...................\f-1
Brake and clutch levers, checking and lubricating ..............................7-\f6\.
Brake fluid ....................................\.....7-\f\f Changing ....................................\...7-\f3
Checking fluid level .......................7-\f\f
Brake lever ....................................\....4-11
Brake pads, checking .......................7-\f1
Brake pedal ....................................\...4-11 Checking ....................................\....7-\f7
Lubricating ....................................\.7-\f7
C Cables, checking and lubricating .....7-\f5
Carbon Monoxide (avoid Carbon Monoxide poisoning).......................\f-\f
Care and storage ...............................8-1\. Catalytic converter ...........................4-13
Checking and lubricating the brake
and clutch levers ...........................7-\f6
Checking and lubricating the brake pedal ....................................\..........7-\f7
Checking and lubricating the cables..7-\f5
Checking and lubricating the sidestand ....................................\...7-\f7
Checking and lubricating the throttle grip and cable ...............................7-\f\.6
Checking the brake pedal ................7-\f7
Checking the sidestand switch .........4-18
Clock mode ....................................\.....4-7
Clutch lever ....................................\...4-10
Clutch lever free play, adjusting .......7-\f0
Consumer information ......................10-1
Controls and instruments ...................3-3 Function ....................................\.......4-1
Coolant ....................................\..........7-1\f
Coolant temperature warning light .....4-4
D Description ....................................\......3-1 Controls and instrument .................3-3
Left view....................................\.......3-1
\bight view ....................................\....3-\f
Dimmer switch....................................\.4-9
Drive chain, cleaning and lubricating ..............................7-\f5\.
Drive chain slack ..............................7-\f3\. Adjusting ....................................\....7-\f3
Checking ....................................\....7-\f3 Cleaning and lubricating ...............7-\f5
E Emission control system (periodic maintenance chart) .........................7-\f
Engine break-in ..................................6\.-3
Engine idling speed, adjusting .........7-15
Engine oil and oil filter element ..........7-9
Engine oil filter element....................7-10
Engine stop switch .............................4-9
Engine trouble warning light...............4-4
F For your safety - Pre-operation checks ....................................\..........5-1
Front fork ....................................\.......4-15 Adjusting ....................................\....4-15
Checking ....................................\....7-\f8
Front wheel ....................................\...7-36 Installing....................................\.....7-37
\bemoving....................................\...7-36
Fuel ....................................\...............4-1\f
Fuel consumption, tips for reducing ...6-3
Fuel meter ....................................\.......4-7
Fuel tank breather hose ...................4-13
Fuel tank cap ...................................4\.-11
Fuses, replacing ...............................7-3\.1
\f Genuine Yamaha Accessories ...........\f-3
H Handlebar switches ............................4-9
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 1

Dimmer switch ..................\o..............4-9
Engine sto\f switch..................\o........4-9
Hazar\b switch ..................\o.............4-10
Horn switch ..................\o..................\o.4-9
Pass switch ..................\o..................\o.4-9
Start switch ..................\o..................\o.4-9
Turn signal switch ..................\o.........4-9
Hea\blight bulb, re\flacing .................7\o-33
High beam in\bicator light ..................\o.4-4
Horn switch ..................\o..................\o....4-9
I I\bentification numbers ..................\o....10-1
I\bling s\fee\b, checking ..................\o...7-15
Ignition circuit cut-off system............4-17 Checking o\feration \froce\bure .....4-18
Immobilizer system ..................\o..........4-1
Immobilizer system in\bicator light ......4-4
In\bicator an\b warning lights ...............4-3\o Coolant tem\ferature warning light ..................\o..................\o.........4-4
Engine trouble warning light ...........4-4
High beam in\bicator light ................4-\o4
Immobilizer system in\bicator light ..................\o..................\o.........4-4
Neutral in\bicator light ..................\o....4-4
Turn signal in\bicator light................4-\o3
Instruments ..................\o..................\o....4-3
Instrument an\b control functions ........4-1
K Keys ..................\o..................\o...............4-1\o L
Labels (location of im\fortant labels) ..1-1
License \flate light bulb, re\flacing....7-35
Location of im\fortant labels ...............1-1\o
Loa\bing ..................\o..................\o..........2-3
Lubricating the brake an\b clutch levers ..................\o................7-\o26
Lubricating the brake \fe\bal..............7\o-27
Lubricating the cables ..................\o....7-25
Lubricating the \brive chain ...............7-2\o5
Lubricating the si\bestan\b .................7\o-27
Lubricating the throttle gri\f an\b cable ..................\o..................\o..7-26
Lubricating the swingarm \fivots.......7-28
M Main switch/steering lock ..................\o.4-2
Mo\bel label ..................\o..................\o...10-1
Motorcycle noise regulation (for Australia) ..................\o..............10-2\o
Multi-function \bis\flay..................\o........4-5 Clock mo\be ..................\o..................\o.4-7
Self-\biagnosis \bevices ..................\o..4-7
Tachometer ..................\o..................\o.4-6
Tri\fmeter an\b tachometer mo\bes ..4-6
N Neutral in\bicator light ..................\o.......4-4
O Oil filter element ..................\o.............7-10
O\feration an\b im\fortant ri\bing \foints ..................\o..................\o..........6-1 Owner’s tool kit ..................\o................7-\o1
P Panels, removing an\b installing .........7-6
Parking ..................\o..................\o...........6-4
Pass switch ..................\o..................\o....4-9
Perio\bic maintenance an\b a\bjustment ..................\o.............7-1
Perio\bic maintenance chart for the emission control system ...........7-2
Pre-o\feration check list ..................\o...5-2
Pre-o\feration checks ..................\o.......5-1
R Rear sus\fension, lubricating............7-27
Rear wheel ..................\o..................\o...7-38 Installing..................\o..................\o....7-39
Removing..................\o..................\o..7-38
Recor\b the i\bentification numbers ...10-1
S Safety information ..................\o............2-1
Seat ..................\o..................\o..............4-14\o
Self-\biagnosis \bevices ..................\o.....4-7
Shift \fe\bal ..................\o..................\o....4-10
Shifting ..................\o..................\o...........6-2
Shock absorber assembly (a\bjusting) ..................\o..................\o.4-16
Si\bestan\b ..................\o..................\o.....4-17
Si\bestan\b, checking an\b lubricating ..................\o..................\o.7-27
Si\bestan\b switch, checking ..............4-18\o
S\fark \flug, checking..................\o........7-8
INDEX
Australia 5/8/10 \á 16:21 Pá\fina 94