2012 YAMAHA XENTER 150 oil change

1
2
3
4
5
6
7
8
9
6-11
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
1
1. Engine oil drain bolt B4. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
5. Check the O-ring for damage and
replace it if necessary.
6. Install the oil strainer, compres-
sion spring, O-ring and engine oil
drain bolt B.TIPMake sure that the O-ring is properly
seated.
7. Install engine oil drain bolt A, and
then tighten both drain bolts to
their specifi ed torques.
Tightening torque:
Engine oil drain bolt A:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)
Engine oil drain bolt B:
32 Nm (3.2 m·kgf, 23.1 ft·lbf)8. Refill with the specified amount
of the recommended engine oil,
and then install and tighten the oil
fi ller cap.Recommended engine oil:
See page 8-1.
Oil change quantity:
1.10 L (1.16 US qt, 0.97 Imp.qt)
ECA11670
NOTICE● Do not use oils with a diesel
speci cation of “CD” or oils of
a higher quality than speci ed.
In addition, do not use oils la-
beled “ENERGY CONSERVING
II” or higher.● Be sure no foreign material en-
ters the crankcase. and B to drain the oil from the
crankcase.
NOTICE:
When re-
moving the engine oil drain
bolt B, the O-ring, compression
spring, and oil strainer will fall
out. Take care not to lose these
parts.
[ECAT1021]
1
1. Oil fi ller cap
1
1. Engine oil drain bolt A
52S-F8199-E0_CS.indd 6-1152S-F8199-E0_CS.indd 6-11
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-12
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
1
1. Final transmission oil fi ller cap4. Remove the fi nal transmission oil
filler cap and its O-ring from the
fi nal transmission case.
5. Remove the fi nal transmission oil
drain bolt and its gasket to drain
the oil from the fi nal transmission
case.
EAU20065
Final transmission oilThe final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the fi nal transmis-
sion oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Start the engine, warm up the fi -
nal transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the center-
stand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
9. Start the engine, and then let
it idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the en-
gine off and check for the cause.
10. Turn the engine off, and then
check the oil level and correct it if
necessary.
To reset the oil change indicator
and oil change tripmeterTIPThe oil change indicator and oil
change tripmeter can be reset when
“OIL CHANGE” and “OIL TRIP” ap-
pear in the multi-function display. (see
page 3-3.)
52S-F8199-E0_CS.indd 6-1252S-F8199-E0_CS.indd 6-12
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-13
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.2 L (0.21 US qt, 0.18 Imp.qt)8. Install the final transmission oil
fi ller cap and its new O-ring, and
then tighten the oil fi ller cap.
9. Check the fi nal transmission case
for oil leakage. If oil is leaking,
check for the cause.
EAU20070
CoolantThe coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specifi ed in the periodic maintenance
and lubrication chart.
EAUT3690
To check the coolant level
The coolant level should be checked
as follows before each ride. In addi-
tion, the coolant must be changed at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Place the vehicle on the center-
stand.TIP● The coolant level must be
checked on a cold engine since
the level varies with engine tem-
perature.● Make sure that the vehicle is po-
sitioned straight up when check-
ing the coolant level. A slight tilt
to the side can result in a false
1
1. Final transmission oil drain bolt6. Install the final transmission oil
drain bolt and its new gasket, and
then tighten the bolt to the speci-
fi ed torque.Tightening torque:
Final transmission oil drain bolt:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)7. Refi ll with the specifi ed amount of
the recommended fi nal transmis-
sion oil. WARNING! Make sure
that no foreign material enters
the final transmission case.
Make sure that no oil gets on
the tire or wheel.
[EWA11311]
52S-F8199-E0_CS.indd 6-1352S-F8199-E0_CS.indd 6-13
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-22
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23095
Checking and lubricating the
cablesThe operation of all control cables
and the condition of the cables should
be checked before each ride, and
the cables and cable ends should be
lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or re-
place it. WARNING! Damage to the
outer housing of cables may result
in internal rusting and cause in-
terference with cable movement.
Replace damaged cables as soon
as possible to prevent unsafe
conditions.
[EWA10711]
Recommended lubricant:
Yamaha Chain and Cable Lube or
engine oil
EAU22721
Changing the brake uidHave a Yamaha dealer change the
brake fl uid at the intervals specifi ed in
the TIP after the periodic maintenance
and lubrication chart. In addition, have
the oil seals of the brake master cyl-
inder and caliper as well as the brake
hose replaced at the intervals listed
below or whenever they are damaged
or leaking.● Oil seals: Replace every two
years.● Brake hose: Replace every four
years. go down. A low brake fl uid level may
indicate worn brake pads and/or brake
system leakage; therefore, be sure to
check the brake pads for wear and the
brake system for leakage. If the brake
fl uid level goes down suddenly, have
a Yamaha dealer check the cause be-
fore further riding.
52S-F8199-E0_CS.indd 6-2252S-F8199-E0_CS.indd 6-22
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
8-1
SPECIFICATIONS SPECIFICATIONS
EAU50910
DimensionsOverall length
1990 mm (78.3 in)
Overall width
690 mm (27.2 in)
Overall height
1135 mm (44.7 in)
Seat height
785 mm (30.9 in)
Wheelbase
1385 mm (54.5 in)
Ground clearance
140 mm (5.51 in)
Minimum turning radius
2100 mm (82.7 in)WeightCurb weight
142 kg (313 lb)EngineEngine type
Liquid cooled 4-stroke, SOHC
Cylinder arrangement
Single cylinder
Displacement
155 cm
3
Bore x stroke
58.0 x 58.7 mm (2.28 x 2.31 in)
Compression ratio
11.00 : 1
Starting system
Electric starter
Lubrication system
Wet sump
Engine oilRecommended brand
YAMALUBE
Type
SAE 10W-40, 10W-50, 15W-40, 20W-40
or 20W-50
–20 –10 0
1020 30 40 50 ˚C 10 30 50 70 90 110 0 130 ˚F
SAE 20W-50SAE 20W-40SAE 15W-40SAE 10W-40SAE 10W-50
Recommended engine oil grade
API service SG type or higher, JASO
standard MAEngine oil quantityPeriodic oil change
1.10 L (1.16 US qt, 0.97 Imp.qt)Final transmission oilType
SAE 10W-30 type SE motor oil
Quantity
0.20 L (0.21 US qt, 0.18 Imp.qt)Cooling systemCoolant reservoir capacity
(up to the maximum level mark)
0.25 L (0.26 US qt, 0.22 Imp.qt)
Air lterAir fi lter element
Oil-coated paper elementFuelRecommended fuel
Regular unleaded gasoline only
Fuel tank capacity
8.0 L (2.11 US gal, 1.76 Imp.gal)Throttle bodyID mark
52S1 01
Manufacturer
AISANSpark plug(s)Manufacturer/model
NGK / CPR9EA-9
Spark plug gap
0.8-0.9 mm (0.031-0.035 in)ClutchClutch type
Dry, centrifugal automaticTransmissionPrimary reduction ratio
1.000
Secondary reduction ratio
10.320 (46 / 13 x 35 / 12)
Final drive
Gear
Transmission type
V-belt automaticChassisFrame type
Underbone
52S-F8199-E0_CS.indd 8-152S-F8199-E0_CS.indd 8-1
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black