2012 YAMAHA RHINO 700 jump start

PERIODIC MAINTENANCE AND
ADJUSTMENT ......................................... 8-1
Owner’s manual and tool kit ................. 8-5
Periodic maintenance chart for the
emission control system ..................... 8-7
General maintenance and lubrication
chart ................................................... 8-8
Hood ................................................... 8-17
Console .............................................. 8-21
Engine oil and oil filter cartridge ......... 8-25
Final gear oil ....................................... 8-39
Differential gear oil ............................. 8-47
Coolant ............................................... 8-55
Axle boots........................................... 8-59
Spark plug inspection ......................... 8-61
Cleaning the air filter element............. 8-67
Drive select lever box check hose ...... 8-79
V-belt cooling duct check hose........... 8-79
V-belt case drain plug......................... 8-81
Cleaning the spark arrester ................ 8-83
Valve clearance .................................. 8-85
Brakes ................................................ 8-87
Checking the front and rear brake
pads ................................................. 8-89
Checking the parking brake pads ....... 8-91
Checking the brake fluid level ............ 8-93
Brake fluid replacement...................... 8-99
8
Checking the brake pedal .................. 8-99
Parking brake lever free play
adjustment ..................................... 8-101
Brake light switch adjustment .......... 8-105
Cable inspection and lubrication ...... 8-107
Brake pedal and accelerator pedal
lubrication ...................................... 8-109
Rear knuckle upper and lower pivot
lubrication (left and right) ............... 8-111
Steering shaft lubrication ................. 8-115
Wheel removal ................................. 8-115
Tire replacement .............................. 8-117
Wheel installation ............................. 8-119
Battery.............................................. 8-121
Jump-starting ................................... 8-131
Fuse replacement ............................ 8-137
Replacing a headlight bulb............... 8-143
Headlight beam adjustment ............. 8-149
Tail/brake light bulb replacement ..... 8-151
Troubleshooting ............................... 8-157
Troubleshooting charts .................... 8-159
CLEANING AND STORAGE ................... 9-1
A. Cleaning .......................................... 9-1
B. Storage ............................................ 9-7
SPECIFICATIONS................................. 10-1
910
1RB60-EE.book Page 3 Thursday, April 7, 2011 10:43 AM

8-131
5B410022
Jump-starting
Jump-starting the vehicle should be avoided.
The battery should be removed and charged in-
stead.
WARNING
To avoid battery explosion and/or serious
damage to the electrical system:

Do not connect the negative lead of the
jumper cable to the negative terminal of
the battery.


Do not touch the positive lead of the jump-
er cable to the negative lead.


Do not reverse the polarity of the jumper
cables when connecting to the batteries.
1RB60-EE.book Page 131 Thursday, April 7, 2011 10:43 AM

8-133 1. Jumper cable positive lead
1. Câble de démarrage positif
1. Cable auxiliar positivo
1
However, if the vehicle must be jump-started, pro-
ceed as follows.
1. Turn the key to “OFF”.
2. Open the hood. (See pages 8-17–8-19 for
hood opening and closing procedures.)
3. Remove the battery compartment cover.
(See pages 8-123–8-127 for battery compart-
ment cover removal and installation proce-
dures.)
4. Remove the console. (See pages 8-21–8-23
for console removal and installation proce-
dures.)
5. Using a charged 12-volt battery, connect the
positive lead of the jumper cable to the posi-
tive terminal of the battery in the vehicle and
the other end of the positive lead to the posi-
tive terminal of the charged battery.
1RB60-EE.book Page 133 Thursday, April 7, 2011 10:43 AM

8-135 1. Jumper cable negative lead
1. Câble de démarrage négatif
1. Cable auxiliar negativo
1
6. Connect the negative lead of the jumper ca-
ble to the negative terminal of the charged
battery and the other end of the negative lead
to an unpainted metal surface of the crank-
case to be started.
7. Start the engine. (Refer to “Starting the en-
gine” on pages 6-7–6-11.)
8. After the engine starts, disconnect the nega-
tive lead of the jumper cable from the crank-
case and charged battery, and then
disconnect the positive lead of the jumper ca-
ble from the charged battery and the battery
in the vehicle.
9. Reinstall the console.
10. Reinstall the battery compartment cover.
11. Close the hood.
1RB60-EE.book Page 135 Thursday, April 7, 2011 10:43 AM