2012 TOYOTA LAND CRUISER engine

638
5-2. Steps to take in an emergency
L/C200_EE (OM60G38E)
If the vehicle becomes stuck
When it is difficult to free the vehicle
Extra high mode (vehicles with 4-Wheel AHC & AVS)
P. 252
Carry out the following procedures if the tires spin or the vehicle
becomes stuck in mud, dirt, or snow.
Stop the engine. Set the parking brake and put the shift
lever to “P”.
Remove the mud, snow or sand from around the rear
wheels.
Place wood, stones or some other material under the rear
wheels to help provide traction.
Restart the engine.
Shift the shift lever to the “D” or “R” position and release the
parking brake. Then, while exercising caution, depress the
accelerator pedal.STEP1
STEP2
STEP3
STEP4
STEP5
Press to turn off Active TRC.

640
5-2. Steps to take in an emergency
L/C200_EE (OM60G38E)
If your vehicle has to be stopped in an emergency
Only in an emergency, such as if it becomes impossible to stop the
vehicle in the normal way, stop the vehicle using the following pro-
cedure:
Steadily step on the brake pedal with both feet and firmly
depress it.
Do not pump the brake pedal repeatedly as this will increase the
effort required to slow the vehicle.
Shift the shift lever to “N”.
If the shift lever is shifted to “N”
After slowing down, stop the vehicle in a safe place by the
road.
Stop the engine.
If the shift lever cannot be shifted to “N”
Keep depressing the brake pedal with both feet to reduce
vehicle speed as much as possible.
To stop the engine, press and
hold the “ENGINE START
STOP” switch for 3 consecu-
tive seconds or more, or press
it briefly 3 times or more in
succession.
Stop the vehicle in a safe place by the road.
STEP1
STEP2
STEP3
STEP4
STEP3
STEP4
Press and hold for 3 seconds or
more, or press briefly 3 times or more
STEP5

5
641 5-2. Steps to take in an emergency
When trouble arises
L/C200_EE (OM60G38E)
CAUTION
If the engine has to be turned off while driving
Power assist for the brakes and steering wheel will be lost, making the brake
pedal harder to depress and the steering wheel heavier to turn. Decelerate
as much as possible before turning off the engine.

646 6-1. Specifications
L/C200_EE (OM60G38E)Engine number
The engine number is stamped on the engine block as shown.
1UR-FE engine
1VD-FTV engine

647 6-1. Specifications
6
Vehicle specifications
L/C200_EE (OM60G38E)
Engine
Gasoline engine
Diesel engine
Model 1UR-FE
Type 8-cylinder V type, 4-cycle, gasoline
Bore and stroke 94.0  83.0 mm (3.70  3.27 in.)
Displacement 4608 cm3 (281.1 cu.in.)
Valve clearance
(engine cold)Automatic adjustment
Drive belt tension Automatic adjustment
Model 1VD-FTV
Ty p e8-cylinder V type, 4-cycle, diesel
(with turbocharger)
Bore and stroke 86.0  96.0 mm (3.39  3.78 in.)
Displacement 4461 cm3 (272.2 cu.in.)
Valve clearance
(engine cold)Automatic adjustment
Drive belt tension Automatic adjustment

648 6-1. Specifications
L/C200_EE (OM60G38E)
Fuel
Gasoline engine
Diesel engine
Fuel typeEU area:
Unleaded gasoline conforming to European
standard EN228 only
Except EU area:
Unleaded gasoline only
Research octane
number95 or higher
Fuel tank capacity
(Reference)93 L (24.5 gal., 20.4 Imp.gal.)
Fuel typeEU area:
Diesel fuel conforming to European
standard EN590
Except EU area (expect Russia):
Diesel fuel that contains 50 ppm or less of
sulfur
Except EU area (Russia):
Diesel fuel confirming to GOST R52368-
2005 (Sulfur max 50 ppm).
Cetane number 48 or higher
Fuel tank capacity
(Reference)93 L (24.5 gal., 20.4 Imp.gal.)

649 6-1. Specifications
6
Vehicle specifications
L/C200_EE (OM60G38E)
Lubrication system
*: The engine oil capacity is a reference quantity to be used when changing the
engine oil. Warm up and turn off the engine, wait more than 5 minutes, and
check the oil level on the dipstick.
Engine oil selection
“Toyota Genuine Motor Oil” is used in your Toyota vehicle. Toyota rec-
ommends the use of approved “Toyota Genuine Motor Oil”. Another
motor oil of matching quality can also be used.
Oil capacity
(Drain and refill —
reference)
*
Gasoline engine
Diesel engineWith filter
7.5 L (7.9 qt., 6.6 Imp.qt.)
Without filter
7.1 L (7.5 qt., 6.2 Imp.qt.)
With filter
9.2 L (9.7 qt., 8.1 Imp.qt.)
Without filter
8.2 L (8.7 qt., 7.2 Imp.qt.)

650 6-1. Specifications
L/C200_EE (OM60G38E)Gasoline engine
Oil grade:
0W-20, 5W-20, 5W-30 and 10W-30:
API grade SL “Energy-Conserving”, SM “Energy-Conserving”, SN
“Resource-Conserving” or ILSAC multigrade engine oil
15W-40 and 20W-50:
API grade SL, SM or SN multigrade engine oil
Recommended viscosity (SAE):
SAE 0W-20 is filled into your
Toyota vehicle at manufacturing,
and the best choice for good fuel
economy and good starting in
cold weather.
If SAE 0W-20 oil is not available,
SAE 5W-30 oil may be used.
However, it should be replaced
with SAE 0W-20 at the next oil
change.
If you use SAE 10W-30 or a
higher viscosity engine oil in
extremely low temperatures, the
engine may become difficult to
start, so SAE 5W-30 or lower vis-
cosity engine oil is recom-
mended.
Oil viscosity (0W-20 is explained here as an example):
• The 0W in 0W-20 indicates the characteristic of the oil which allows
cold startability. Oils with a lower value before the W allow for easier
starting of the engine in cold weather.
• The 20 in 0W-20 indicates the viscosity characteristic of the oil when
the oil is at high temperature. An oil with a higher viscosity (one with a
higher value) may be better suited if the vehicle is operated at high
speeds, or under extreme load conditions.
Temperature range anticipated before
next oil change.
Preferred