2012 SSANGYONG RODIUS 4WD

06-33310-01
1. SPECIFICATIONS
Description Specification
StructureUniversal joint with yoke arm and spider and CV
joint
Front propeller shaft (4WD) One universal joint and one CV joint
Rear propeller shaft Two universal joint and one CV joint
Run-out below 0.4 mm
UnbalanceMax. 18g·cm / 4,500rpm
Length of front
propeller shaft4WD A/T 531.2 ± 1.0 mm
Length of rear
propeller shaft2WD M/T 1892.1 ± 2.0 mm
A/T 1975.1 ± 2.0 mm
4WD A/T 1593.1 ± 2.0 mm

06-53310-01
1. OVERVIEW
The propeller shaft transfers the power through the transmission and transfer case to the
front/rear axle differential carrier (final reduction gear). It is manufactured by a thin rounded steel
pipe to have the strong resisting force against the torsion and bending. Both ends of propeller
shaft are connected to the spider and the center of propeller shaft is connected to the spline to
accommodate the changes of the height and length. The rubber bushing that covers the
intermediate bearing keeps the balance of rear propeller shaft and absorbs its vibration.
Function of propeller shaft ▶
Transmits driving torque.
Compensates the angle change (universal joint / CV joint).
Compensates the axial length change (splines for the slip joint). -
-
-
4WD AT 2WD MT

07-4
3. MAJOR CHANGES
Front Sub Frame
Old New
The engine mounting insulators (A) have been changed according to newly equipped engine
(D20DTR). It improves the durability and NVH.
Front Knuckle Assembly
Old New
The front knuckle assembly has been changed according to new 4WD system (Part-time T/C).
Hub bearingLocking hub
actuator

07-74411-01
Coil Spring ▶
Description 4WD 2WD
Spring rate (kg/mm)10.01 ± 5% 10.01 ± 5%
Coil diameter (mm)16.7 16.7
Inner diameter
(mm)D 158.3 58.3
D 288.3 88.3
Spring identificationNone + Red or Blue Yellow + Red or Blue
Number of windings8.49 8.49
Number of active windings6.99
CVW (Curved
Vehicle Weight)Height (mm)256.0 256.0
Weight (kg)976.9 ± 4% 834.9 ± 4%
Stress (kg/mm)69.53 59.42
Winding directionClockwise Clockwise

07-10
(2) Coil Spring
High tensile steel used.
Minimum length should be 20 mm longer than the fully compressed length.
Spring seat used. -
-
-
Description 4WD 2WD
Part number45110-21000 45110-21000
Spring rate (kg/mm)12.0 ±5% 12.0 ±5%
Coil diameter (mm)15.9 15.9
Inner diameter (mm)69.1 69.1
Pitch (mm)85.0 85.0
Number of windings9.55 9.55
Number of active windings8.35 8.35
CVW (Curved Vehicl
e
Weight)Height (mm)250 250
Weight (kg)880 880
Stress (kg/mm)
62.1 62.1
Winding directionClockwise Clockwise
Spring length (mm)323.3 323.3
Dimension ▶

09-74891-01
1. ESP Indicator2. Steering Wheel Angle
Sensor
3. ESP OFF Switch 4. Sensor Cluster
Front Wheel Speed Sensor
4WD 2WDRear Wheel Speed
Sensor

10-54891-01
Warning Lamps
EBD warning lamp ABS warning lamp
2. COMPONENTS AND LAYOUT
The basic functions of ABS system are same with previous version. However, the wheel speed sensing
type is different from previous version.
For details about the components, refer to Chapter "ESP".
Front Active Wheel Speed Sensor
4WD 2WD
ABS HECU
Rear Active Wheel
Speed Sensor