2012 SSANGYONG RODIUS remote control

02-398710-01
The PANIC warning outp<009c009b00470090009a004702c80076007502c90047004f009b008f008c008d009b0047008b008c009b008c00990099008c0095009b0047008f00960099009500500047009e008f008c009500470099008c008a008c0090009d00900095008e0047009b00
8f008c00470077006800750070006a0047009a0090008e0095>al from
the remote control key (pressing PANIC button for less than 0.5 ~ 1.0 second).
<007b008f008c00470077006800750070006a0047009e00880099009500900095008e00470096009c009b0097009c009b00470090009a004702c80076006d006d02c90047009e008f008c009500470099008c008a008c0090009d00900095008e0047008800
9500a00047009a0090008e0095008800930047008d00990096>m the remote control key
during PANIC warning.
Followings are theft deterrent warnings:
This function operates only in armed mode.
The system sends the current vehicle conditions (LOCK, engine running) when the PANIC
warning is turned off by the remote control key. 1.
2.
3.
4.
5.The theft deterrent warning is canceled when receiving PANIC signal from the remote control
key during theft deterrent.
<007b008f008c0047009b008f008c008d009b0047008b008c009b008c00990099008c0095009b0047009e00880099009500900095008e00470096009c009b0097009c009b00470090009a004702c80076007502c90047009e008f008c00950047009b008f00
8c0047009b008f008c008d009b0047008b008c009b008c0099>rent conditions are
<008c009a009b0088008900930090009a008f008c008b0047008b009c009900900095008e00470077006800750070006a0047009e00880099009500900095008e0047004f0077006800750070006a00470096009c009b0097009c009b00470090009a004702
c80076006d006d02c900500055>
<007b008f008c00470077006800750070006a0047009e00880099009500900095008e00470096009c009b0097009c009b00470090009a004702c80076007502c90047009e008f008c009500470099008c008a008c0090009d00900095008e0047009b008f00
8c00470077006800750070006a0047009a0090008e00950088>l from the remote control
key in Armed Ready / Armed / Warning Completion / Relock Ready mode (maintaining the
theft deterrent mode). 1)
2)
3)
(2) PANIC Warning

03-77010-06
ECU
Immobilizer Indicator and Warning Lamp ▶
This indicator comes on when the ignition
key is communicating with the engine
control unit (during engine starting) and
goes out after starting the engine.
When turning the ignition key to ON
position, the ECU transmits the challenge
message to the immobilizer unit to verify
whether the key is valid. (1)
Only when the two signals are identical, it
recognizes the key as the authorized one and
transmits the positive message to the ECU.
The ECU allows the engine to be started. (6)
(7)
Do not drop or shock to the transponder in the key as it may be damaged.
With a damaged transponder, the engine cannot be started.
When you erase the code or register an extra key, let the owner attend on the site.
In any case, the immobilizer system cannot be removed from the vehicle. If you attempt to
remove it and damage the system, starting will be impossible, so never attempt to remove,
damage or modify it.
The remote engine starter cannot be installed on the vehicle equipped with the immobilizer
system. -
-
-
-
-Lamp ON: in communication
Blinking twice for one second: immobilize
r
system failure
Blinking once for two seconds: immobiliz
e
unit is not coded
The immobilizer indicator does not
come on if the communication time
between immobilizer key and ECU is
too short.
Immobilizer Indicator and Warning Lamp

06-4
4WD Switch, Headlamp
Leveling Switch, Rear Wipe
Switch
Outside Rearview
Mirror
Adjusting/Folding
Switches
Remote Control Switches on Steering Wheel
Window switch
1. LAYOUT
Volume button
Seek buttonManual gear shift
down switch
Power buttonManual gear shift
up switch
Mode button
Mute button
Bluetooth switch

10-6
Front Speaker
1. LAYOUT
Bluetooth Microphone
Bluetooth microphone
Tweeter speaker
Audio head unit
Audio remote control switches

02-14
3166-00 Extension housing ▶
Lever assembly - Semi remote
Lever - Shift
Boot - Rubber
Ring - Retainer
O-ring
Bearing
Shim
Arm - Control
Damper assembly
Rod assembly
Bushing assembly - TGS mounting
Pin - TGS mounting
Pin - Spring
Pin - Spring
Adapter - Case 1.
3.
4.
5.
6.
7.
8.
9.
10.
13.
14.
15.
16.
17.
20.Bolt - Flange (42.1 ~ 53.9 Nm)
Seal - Oil
Seal - Oil
Pin - Dowel
Switch - Neutral (29.4 ~ 34.3 Nm)
Gasket
Bolt - Interlock (14.7 ~ 21.5 Nm)
Pin - Detent
Switch - Backup lamp (29.4 ~ 34.3
Nm)
Bolt - Fork hinge (53.9 ~ 67.6 Nm)
Bearing - Poppet ball (29.4 ~ 41.1
Nm)
Bolt - Guide (14.7 ~ 21.5 Nm)
Bolt (2.9 ~ 4.9 Nm)
Bracket - Wiring 21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.

02-153170-01
Sectional viewFront view
1. OVERVIEW
1) Characteristics of Transmission
Forward and Reverse gears are helical gear.
The clutch is operated by concentric slave cylinder (CSC).
To prevent the improper gear shift, semi-remote control system has been introduced.
To prevent the gears from engaging improperly, the synchronizer mechanisms and
independent interlock systems are installed on 1/2 gears, 3/4 gears, 5/6 gears and reverse
gear.
The High-Force system for reverse gear shift has been introduced.
The synchronizer has three types: Triple (1, 2, 3, R), Double (5), Single (4, 6) -
-
-
-
-
-
6-speed M/T