2012 SSANGYONG RODIUS length

09-31451-01
1. SPECIFICATION
AlternatorCrankshaft pulley : Alternator pulley 1 : 2.94
Normal output (idling/2200 rpm) 70/140A
Regulator voltage 14.6 V
BrushLength 12.5mm
Wear limit 7mm
BatteryType MF
Capacity 90 AH
Unit Description Specification

08-138610-11
4. FUNCTIONS OF RAIN SENSOR
1) Windshield Glass and Coupler Attachment
Check the outer windshield surface of sensing area for wear, damage and scratch. The sensor is
able to compensate the wear up to a specific level. Check the coupler attached surface of
windshield for porosity. If the porosity exists, the sensor cannot function properly.
2) Recognition of AUTO Mode
3) Instant Wipe Function
When the variable resistance knob on the multifunction wiper switch is turned by each 1 stage
from low sensitivity (Smark) to high sensitivity (F mark), the wiper operates one cycle.
And, the wiper also operates during raining up to 5 minutes after rain stops.When the engine is started with the wi
per switch “AUTO” position, the wiper operates one cycle
<009b009600470099008c009400900095008b004700880047008b00990090009d008c00990047009b008f0088009b0047009b008f008c0047009e00900097008c00990047009a009e0090009b008a008f00470090009a004700900095004702c80068007c00
7b007602c9004700970096009a0090009b0090009600950055>
<007e008f008c00950047009b008f008c0047009e00900097008c00990047009a009e0090009b008a008f00470090009a0047009b009c00990095008c008b0047009b0096004702c80068007c007b007602c90047008d00990096009400470076006d006d00
530047009b008f008c0047009e00900097008c009900470096>perates one cycle. It always
operates one cycle for the initial operation, however, the wiper does not operate afterwards to
<00970099008c009d008c0095009b0047009b008f008c0047009e00900097008c00990047008900930088008b008c0047009e008c0088009900470090008d004700950096009b0047009900880090009500900095008e0047009e008f008c00950047009b00
9c0099009500900095008e0047009b008f008c0047009e0090>per switch to “AUTO” from
<02c80076006d006d02c900550047006f0096009e008c009d008c009900530047009b008f008c0047009e00900097008c0099004700960097008c00990088009b008c009a0047009c00970047009b00960047005c0047009400900095009c009b008c009a00
470088008d009b008c0099004700990088009000950047009a>tops.
If this function does not occur, check No. 2 terminal on the rain sensor. If any defective cannot
be found, check the wiper relay (LOW) for defective. 1.
2.
3.If the installed wiper brushes are out of specification (size and length), the rain sensing area
<008a0088009500950096009b00470089008c0047008d009c0093009300a00047009e00900097008c008b005500470047007000950047009b008f0090009a0047008a0088009a008c00530047009b008f008c004700990088009000950047009a008c009500
9a0096009902c5009a0047009a008c0095009a0090009b0090>vity could be decreased and the
wipers are not properly operated - The followings are the detailed description of the functions and operations of the rain sensing
wiper control.
<0068009a0047008b008c009a008a009900900089008c008b00530047009b008f008c0047007a007b0070006a007a00470099008c008a0096008e0095009000a1008c009a0047009b008f008c0047009e00900097008c00990047009a009e0090009b008a00
8f004702c80068007c007b007602c9004700970096009a0090>tion. If there are not any
problem, go to diagnosis mode in STICS and check the terminal that receives signal from
wiper and communication lines between rain sensor unit and STICS. -
When the variable resistance knob is rotated by 4 stage from 0 stage without stoping, the
wiper operates one cycle. The wiper operates one cycle when changing the wiping stage (0
→ 1, 1 → 2, 2 → 3). -

03-93010-00
2) Overview
Driving elements ▶
The driving elements consist of two flat surfaces machined to a smooth finish.
One of these is the rear face of the engine flywheel and the other is the clutch pressure plate. The
clutch pressure plate is fitted into a clutch steel cover, which is bolted to the flywheel.
Driven elements ▶
The driven element is the clutch disc with a splined hub which is free to slide lengthwise along the
splines of the input shaft.
The driving and driven elements are held in contact by spring pressure. This pressure is exerted
by a diaphragm spring in the clutch cover pressure plate assembly.
Operating Elements ▶
The clutch "release" system consists of the clutch pedal and clutch release cylinder.
This system directly releases the clutch by using hydraulic pressure while the conventional clutch
system releases the clutch by using release lever and release fork. This system provides higher
efficiency than conventional clutch system, and its durability is superior.
Clutch master cylinder (mounted on clutch pedal)
Concentric slave cylinder pipe (mounted inside of transmission) -
-

05-33240-01
Weight 32.4 kg (including oil)
Oil capacity 1.4L
Oil type ATF DEXRON II or III
Location Transfer case
Major element Housing Part-time
Bolt 11EA, M8 x 1.25
Input shaft A/T: outer spline
Description Specifications
Total length 343mm
1. SPECIFICATIONS

06-33310-01
1. SPECIFICATIONS
Description Specification
StructureUniversal joint with yoke arm and spider and CV
joint
Front propeller shaft (4WD) One universal joint and one CV joint
Rear propeller shaft Two universal joint and one CV joint
Run-out below 0.4 mm
UnbalanceMax. 18g·cm / 4,500rpm
Length of front
propeller shaft4WD A/T 531.2 ± 1.0 mm
Length of rear
propeller shaft2WD M/T 1892.1 ± 2.0 mm
A/T 1975.1 ± 2.0 mm
4WD A/T 1593.1 ± 2.0 mm

06-53310-01
1. OVERVIEW
The propeller shaft transfers the power through the transmission and transfer case to the
front/rear axle differential carrier (final reduction gear). It is manufactured by a thin rounded steel
pipe to have the strong resisting force against the torsion and bending. Both ends of propeller
shaft are connected to the spider and the center of propeller shaft is connected to the spline to
accommodate the changes of the height and length. The rubber bushing that covers the
intermediate bearing keeps the balance of rear propeller shaft and absorbs its vibration.
Function of propeller shaft ▶
Transmits driving torque.
Compensates the angle change (universal joint / CV joint).
Compensates the axial length change (splines for the slip joint). -
-
-
4WD AT 2WD MT

07-8
Shock Absorber ▶
Fully extended length
547.0 ± 0.3 (mm)
Fully compressed
length462.0 + 0.3 (mm)
Operating distance85.0 (mm)

07-94411-01
5. DIMENSIONS OF REAR SUSPENSION
(1) Shock Absorber
Keep the suitable distance when compressed and extended.
Minimum length should be 10 mm longer than the fully compressed length. -
-
Dimension ▶
Maximum operating length Minimum operating length
Operating distance
487.0 ± 0.3 (mm) 326.0 + 0.3 (mm) 160.4 (mm)
Marking ▶
X: Part number
Y: Lot number
Ex:
3C12
12.............(Day)
3...............(Month)
2003......(Year)