2012 SSANGYONG NEW REXTON sensor

Diff. pres. sensor: Measure
pressure between front
side and rear side of CDPF
ECU (DCM 3.7)
Injector: Control post
injection
D. Operation process
When the differential pressure sensor detects the pressure difference between the front and the rear
side of CDPF, the sensor sends signal indicating the soot is accumulated and the post injection is
performed to raise the temperature of exhaust gas. The amount of fuel injected is determined according
to the temperature of exhaust gas detected by the rear temperature sensor. If the temperature is below
low load range, the amount of post injection and the amount of intake air are controlled. It is to raise the
temperature by increasing the amount of fuel while decreasing the amount of intake air.
Front EGT sensor:
Measure DOC temp.
Rear EGT sensor: Measure
DPF temp.
Electronic throttle
body: Control intake
air mass
T-MAP sensor
Intake air
mass
Exceed PM
limitBooster
pressure/
temperaturePost injection
Control intake
air mass

Engine Compartment Layout
Engine assembly
Engine oil dipstick
Vacuum pump
Oil filter and cooler
Fuel filter and priming pump
Brake booster
Brake oil tank
AQGS unit
Washer fluid filler cap
Engine compartment fuse box
PTC relay box
Battery
Vacuum modulator (for VGT turbo charger) 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.FFH Assembly (Only for vehicle with FFH)
Power steering oil tank
Engine oil filler cap
Fan shroud
E-EGR Valve
High-capacity PCV oil separator
HFM sensor (6.0)
VGT turbo charger
Air cleaner housing
2Coolant surge tank
ABS/ESP HECU (Including TPMS function:
optional)
Exhaust gas FRT Temp. sensor (T3) 14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.

0000-00
Major Sensors and Components

2) Engine Structure
1. TVD (Torsional Vibration Damper)
2. Air conditioner compressor
3. Power steering pump pulley
4. Idle pulley
5. Coolant pump pulley
6. Alternator7. Viscos fan clutch
8. Auto tensioner pulley
9. Auto tensioner
10. Poly-grooved belt
11. Cam position sensor
12. Drive plate (MT: DMF)13. Oil filter
14. Vacuum pump
15. Crank position sensor
16. EGR valve
17. Power steering pump
18. EGR to center pipe
Front View
Rear View

1212-01
Top View
19. Cylinder head cover
20. Intake manifold
21. Water outlet port
22. Common rail
23. Fuel pressure sensor24. Fuel pipe
25. Injector
26. Fuel return line
27. Oil filler cap
28. Glow plug29. Booster pressure sensor
30. PCV valve and oil separator
31. Oil dipstick
32. EGR-LH (#1) pipe

1881-09
3) Fuel Rail - Chrome Color
D27DTP & D27DT (EU IV)
Common rail)
D27DT
Common rail)The I.D and O.D of the fuel rail between
HP pump and common rail are increased
according to the increased amount of fuel
injection.
Also, the engine ECU, HFM sensor and
EGR system are changed to control the
fuel injection volume and engine more
precisely.

2321-01
1. INTAKE SYSTEM LAYOUT
The intake system for the D27DTP (POWER UP) engine is equipped with the throttle body that has
a flap to block the air coming to the engine when the engine is switched off. Therefore, the
structure of the intake manifold has been changed.
Also, the improved HFM sensor (from HFM5.0 to HFM6.0) has been installed to control the intake
air precisely so that the NOx in the exhaust gas can be decreased.

1725-12
1. OVERVIEW FOR CDPF (EURO IV)
1) General Description
The CDPF (Catalyst & Diesel Particulate Filter) was installed to the Rexton II D27DTP engine
previously. However, it is now installed to the all 2009 DI engine models, except the
Actyon
Sports. The DI engine types installed to Rexton are D27DTP, D27DT and D20DT, and their CDPF,
related sensor and operation logic are the same.
This section describes the CDPF system (based on Euro IV) which is installed to the Rexton II
D27DTP engine (older model).
2) Compatibility of CDPF System by Vehicle Model
Rexton II: Same CDPF system for D27DTP and D27DT engines (including its components)
Kyron & Actyon: Same CDPF system for D27DT and D20DT engines (including its components)
The CDPF assemblies installed to the Euro IV D27DTP Rexton II and 2009 Rexton II are
different in their mounting layout, but their front/rear exhaust temperature sensors and
differential pressure sensors are same. -
3) System Met with Euro IV Regulations
E-EGR valve
EGR cooler
Engine ECU (Ver. 3.2)
HFM sensor
C3I injector
Electronic throttle valve (body)
Other engine mounting components -
-
-
-
-
-
-
For details about the modified components and system related to the Euro IV regulations, refer to
the 2008 Rodius engine service manual.