2012 SSANGYONG NEW ACTYON SPORTS height

09-14
Specified value (B)155mm
Push rod
Stop lamp
switch Pedal Height ▶
Check the pedal height with below
procedures: -
Start the engine and measure the length
(A) between floor mat and pedal.
If the measured value is out of the
specified value, adjust the length. 1.
2.
Adjust the pedal height with below
procedures: -
Disconnect the stop lamp switch connector.
Unscrew the lock nut and remove the stop
lamp switch assembly.
Loosen the lock nut on the pedal push rod.
Turn the pedal push rod to adjust the pedal
height.
Tighten the lock nut.
Install the stop lamp switch assembly.
Connect the stop lamp switch connector.
Check if the stop lamps come on when
pressing the brake pedal around 5 mm.
If the stop lamp dpes not come on, adjust
the stop lamp switch assembly again.
If the stop lamps come on, tighten the lock
nut and measure the pedal height again. 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.

09-16
Let the engine run for 1 to 2 minutes and
stop it. If the brake pedal stroke is
shortened as pumping the brake pedal,
the system is normal. If not, the system is
defective.
Depress the brake pedal several times
with engine off. If the brake goes down
when starting engine with pedal
depressed, the system is normal. If not,
the system is defective.
Depress the brake pedal when the engine
is running. If the pedal height is not
changed for 30 seconds after stopping
the engine, the system is normal. If not,
the system is defective. 1.
2.
3.
If the above three checks are OK, the system
is normal. If any condition is not met, check
the valve, vacuum hose and brake booster. Brake Booster ▶

13-14
Tire Unit Indication ▶
Tire Inflation Pressure (32 psi) ▶
Proper inflation
pressureExcessive inflation pressure Low inflation
pressure
Aspect ratio (%)
= Nominal section height (H) / Nominal section
width (W)
X 100
The contact area between the
ground and tire faces the
tread layer completely. Thus
the driving force and the
braking force are optimized,
and the tire is worn out evenly
resulting in increased life.The contact area between
the ground and tire is not
enough, so the tire is worn
out unevenly and the tire is
vulnerability to outside
influence.The contact area between the
ground and tire is excessive,
so a lot of heat is generated
and the tire is worn out
unevenly and abnormally.
Tread width Tread width Tread width

03-2
1. FRONT SEAT
Seat switch (driver’s)
Sliding
Seat height adjustment
Seatback recliningSeat warmer switch

03-57410-01
Seat assembly - front
Seat assembly - front
Seat assembly - front
Seat assembly - front
Shield - cover
Knob - power seat slide
Knob - power seat recliner
Lever assembly - lumbar support
Bolt
Cover - front seat front puter
Cover - front seat rear
Headrest assembly - front
Switch assembly - power seat
Sleeve - headrest 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
14.
15.Sleeve - headrest
Cover - front seat front
Knob - manual seat recliner
Regulator - height adjuster
Warmer assembly - front seatback
Warmer assembly - front seat cushion
Motor & plate assembly - front seat
Motor assembly - front seat height
Motor assembly - front seat recliner
Back board assembly - front seat
Cover - inner shield
Adjuster assembly - manual height
Recliner assembly - front outer
Recliner assembly - front inner 16.
17.
18.
19.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.

03-10
Components ▶
Seat belt assembly - front
Height adjuster assembly - front seat belt
Cover - front seat belt D-ring
Screw
Buckle assembly - front 1.
2.
3.
4.
5.

03-14
Pretensioner ▶
The seat belt pretensioner is a unit to retract the seat belt instantly by igniting the inflator in the
pretensioner when the front air bag system is activated.
It also increases safety effect of the seat belt by limiting the front seat occupants from moving
forward and keeping occupants in correct posture.
The load limiter is also installed to reduce chest impact to a front seat occupant by loosening the
seat belt while maintaining the force applied by the seat belt uniformly when the pretensioner
retracts the seat belt instantly. The seat belt pretensioner operates first, and then the load limiter
operates.
Height Adjuster
It is to improve comfort and
optimize restrictive
performance in case of a
collision by adjusting the
belt position to the
occupant's shoulder.Driver’sFront passenger’s
Pretensioner