2012 SSANGYONG KORANDO automatic

03-28
Seat belt reminder ▶
Operating conditions for seat belt reminder are as follows: IGN ON, engine running (over 300 rpm),
vehicle speed of 25 km/h or higher, driver seat belt unfastened, passenger seat belt unfastened and
passenger seat occupied. In addition, if the seat belt reminder is activated at the speed of 25 km/h or
higher and the speed reduces to below 25 km/h within 5 minutes, the interior buzzer sound stops. The
buzzer sounds for 5 minutes again when the speed is 25 km/h or higher.
The seat belt reminder stops its operation when fastening the seat belt, but starts the operation again if
unfastening the seat belt.
If the seat belt reminder is initially operated due to unfastened driver seat belt, the buzzer sounds with
the interval of 0.02s ON/1.18s OFF, the instrument cluster sends the driver seat belt warning signal
(SBR) and the seat belt warning lamp stays on.
At this time, the buzzer sounds for 5 minutes.
If the seat belt reminder is operated due to unfastened passenger seat belt when the passenger seat
belt reminder sensor detects that the passenger seat is occupied, the instrument cluster sends the
driver seat belt warning signal and the seat belt warning lamp stays on.
For this case, the indicator shows each status of the driver and passenger seats but the indoor buzzer
is common to both seats.
If the simultaneous operating condition for the indoor buzzer is met, the driver seat has the priority.
If the driver seat belt is fastened, the same operation is also carried out in the passenger seat
automatically.
The buzzer and the warning lamp are operated according to the vehicle speed as below table during
the seat belt reminder operation. 1.
2.
3.
4.
5.
Seat belt reminder operation
<007700990090009600990090009b00a000470096008d00470089009c00a100a1008c0099004700960097008c00990088009b00900096009500610047007a0069007900470d7d00470072008c00a000470099008c009400900095008b008c00990047009e00
880099009500900095008e00470d7d0047007a009c00950099>oof warning ⇒ Tail lamp ON
<009e00880099009500900095008e00470d7d0047006f008800a100880099008b0047009e00880099009500900095008e0047008d00930088009a008f008c009900470d7d0047007b009c009900950047009a0090008e009500880093004700930088009400
970055> 6.
Buzzer Warning lamp
25 Km/h ~ 49 Km/h 0.02s ON / 1.18s OFF Keep ON
50 Km/h ~ 99 Km/h 0.02s ON / 0.98s OFF Keep ON
10 Km/h ~ 49 Km/h 0.02s ON / 0.78s OFF Keep ONFunction
Vehicle speed
Seat belt remind warning lamp (EU only)
This lamp comes on for 6 seconds after turning on the ignition switch. If the vehicle speed goes
over 10 km/h without fastened the seat belt, the inside buzzer sounds. -

03-318710-01
7) Room Lamp
Door coupled room lamp and dimming control ▶
When opening any of doors while the room lamp switch in overhead console is pressed in ("Door"
coupled position), the room lamps come on. If the key is removed and door stays open, the room lamps
automatically goes off after 10 minutes. The sleep mode will be deactivated when the door is locked or
closed with the lamp OFF automatically.
When closing the door with IGN ON, the room lamps go off immediately.
When closing the door with IGN OFF, the room lamps stays on for 2 seconds and are dimmed out for
3 seconds.
When turning the ignition switch to ON position during dimming out operation, the room lamps go off
immediately.
When receiving the door unlock signal with IGN OFF, key removed and door closed, the room lamps
come on for 30 seconds. (It operates depending on REKES unlock and manual unlock signals for
BCM with SKM.)
4. When receiving the door unlock signal again in Step (4), the overhead room lamp and center room
lamp stay on for 30 seconds additionally. (For BCM with SKM, the extension depends on the REKES
unlock signal.)
When opening a door during the linked and dimming operation, the room lamps stays ON. When
closing it again, the system performs the operation in Step (1) and (2).
When all the door switches are changed from its closing state to its opening state, the room lamps are
dimmed out. The room lamps go off immediately when entering into the theft deterrent mode. (For
BCM with SKM, door lock is carried out by the REKES lock and manual lock signals.)
The room lamps come on when the auto approach function is activated. 1.
2.
3.
4.
5.
6.
7.
8.Room lamp control by door coupled room lamp operation ▶

03-32
8) Key Hole Illumination
When opening the door with IGN OFF, the key hole lamp comes on.
When closing the door, the key hole lamp stays on for 10 seconds and goes off.
When turning the ignition switch to ON position during the operation of key hole illumination, it goes of
f
immediately.
When receiving the door lock signal (entering into theft deterrent mode), the lamp goes off.
The key hole illumination function has a priority over the immobilizer function.
If the communication with the immobilizer is interrupted, the lamp comes on for 11 seconds with the
interval of 0.5s ON/0.5s OFF regardless of the operating conditions of key hole lamp.
When turning the ignition switch to ON position in "Virgin" condition, the lamp comes on for 8 seconds
with the interval of 0.5s ON/0.5s OFF. 1.
2.
3.
4.
5.
6.
(*1) ON: IGN ON
OFF: IGN OFF(*2) Open: driver or passenger door is open
Close: driver and passenger door are closed
Room lamp OFF control ▶
The room lamps stop operating when the BCM enters into the theft deterrent or sleep mode. (This is
to prevent battery discharge if the overhead room lamp and sensor room lamp switch is ON position.)
The room lamps go off automatically 10 minutes after the key is removed. After that, if the door unlock
or all door open signal is received and the key is inserted, the sleep mode is deactivated and the room
lamps operate for another 10 minutes.
The room lamps come on when the key is inserted (BCM without SKM) or the ignition switch is turned
to "ACC" or "ON" position (BCM with SKM) while the room lamps are OFF. 1.
2.
3.

03-358710-01
10) Keyless Entry
Transmitter (REKES key) ▶
When the user operates the switch of the remote control key, the vehicle control messages formatted by
its CPU are sent to the main unit wirelessly. The, the CPU control the vehicle and the main unit controls
the vehicle operation.
Door unlock/panic buttonDoor lock
Door unlock/panic button ▶
Unlocking door and tailgate (briefly press)
If you press this button, it unlocks all doors and the tailgate and deactivates the theft deterrent mode.
When the theft deterrent mode is deactivated, the emergency hazard lights blink once.
If the door, tailgate or engine hood is not opened within 30 seconds after unlocking the door with the
remote control key in theft deterrent mode, the door is locked automatically, hazard warning flasher
blinks twice and buzzer sounds once. (entering into theft deterrent mode)
Panic function (press and hold for more than 2 sec)
When pressing (over 2 sec) the button, the hazard warning flasher blinks and buzzer sounds for
about 30 seconds.
Press the UNLOCK or PANIC button to deactivate this function. 1.
-
-
-
2.
-
-

03-38
After 30 seconds delay auto door lock ▶
If a door or tailgate is not opened within 30 seconds after unlocking the doors with remote control key
in theft deterrent mode, all doors will be automatically locked again (change to theft deterrent mode).
If any door is not opened or the key is not detected within 30 seconds after receiving the unlock
signal, the lock signal is outputted and theft deterrent mode is activated.
When entering into the theft deterrent mode, the turn signal lamps blink twice and the exterior buzzer
sounds once for SKM the lamps blink twice and burglar alarm horn sounds once for REKES. 1.
2.

03-398710-01
11) Door Lock/Unlock Control
The BCM with SKM receives wake-up source for driver door lock/unlock switch, passenger door
lock/unlock switch, rear door (left/right) lock switch, central door lock/unlock switch status through the
electric wire (hardwire).
Door lock/unlock control by door LOCK switch ▶
When moving the driver or passenger door lock (knob) switch to LOCK from UNLOCK position, BCM
sends the LOCK signal for 0.5 seconds.
When moving the driver or passenger door lock (knob) switch to UNLOCK from LOCK position, BCM
(UNLOCK) operation by the door lock (knob) switch is not available when sending the LOCK
(UNLOCK) signal by any other method such as remote control key.
When reconnecting the battery, the door lock (knob) switch is not operational regardless of the door
lock switch positions.
All doors stay unlocked when receiving the door lock signal in 0.5 seconds after closing the doors. 1.
2.
3.
4.
5.The status for key cylinder switch and latch position switch is received through the door lock/unlock
switch.
When door lock signal is outputted due to failure of the door knob switch and door open switch and
automatic unlock signal is transmitted 5 times for 1 minute, BCM forcibly lock the doors without
unlocking.
However, door unlock command works normally and deactivates forcible unlock. -

03-40
Door lock/unlock control by central door lock switch ▶
When pressing the central door lock/unlock switch, BCM sends the LOCK or UNLOCK signal
according to the previous condition of driver door lock switch for 0.5 seconds.
The central door dock switch is not available when the system is in theft deterrent mode.
When turning the ignition off, all doors are automatically unlocked if any of the door lock (knob)
switches is in LOCK position.
When pressing the central door lock switch with any door open, the system unlocks the doors
immediately after locking them. 1.
2.
3.
4.
Door lock/unlock control by REKES signal ▶
When receiving the door lock signal, BCM sends the LOCK signal for 0.5 seconds.
When receiving the door unlock signal, BCM sends the UNLOCK signal for 0.5 seconds. 1.
2.

03-438710-01
Auto door lock control ▶
Door lock output is activated when the vehicle speed is maintained above 30 km/h with IGN1 ON.
However, if all the doors are locked or fail, lock output is not activated.
If any of doors is not locked after Step (1), BCM activates the door lock output up to 5 times.
If the door is still unlocked, BCM considers the door as Fail.
If the failed door is changed from UNLOCK to LOCK, the fail record the side fascia panel.
If there is any failed door, the auto door lock function is not available.
(Even though the vehicle speed is increased over 30 km/h again after decreased below 30 km/h, BCM
does not send the auto door lock signal.)
When receiving the unlock signal for another door during Step (2), BCM sends the lock
signal for the door up to 5 times.
The unlock output is activated automatically when door lock output conditions are met by this function
or the IGN1 switch is turned to OFF from ON position (even though the lock output is not activated if
the vehicle speed is maintained above 30 km/h under lock condition). (If the LOCK condition is
established with the ignition switch ON, the system outputs UNLOCK signal unconditionally when
turning the ignition switch to OFF position.)
However, whether the door lock output condition is met or not is initialized when the IGN1 switch is
turned to OFF position.
When turning the ignition off, the fail record for a door will be initialized.
If any of door lock switches is in LOCK position when turning the ignition off, all doors are unlocked. 1.
2.
3.
4.
5.
6.
7.
8.
9.
(*1) Lock: All doors including tailgate are locked.
Unlock: All doors including tailgate are unlocked.