2012 SSANGYONG KORANDO roof

05-48
Pin No.Message
Operating condition
Domestic Export
Cruise control This message comes on when the ECO cruise mode
is deactivated.
EMSThis message comes on when the engine is faulty.
LampThis message comes on when the tail lamps are ON
with the ignition in the "OFF" or "ACC" position.
SUNROOF
SYSTEMFor the vehicle with SKM, this message comes on
when the sunroof is open with the ignition in the "OFF"
or "ACC" position. For the vehicle without SKM, this
comes on when the sunroof is open with the ignition in
the "OFF" position and the key removed.
Low fuel level This message comes on when the remaining fuel is
insufficient.
ESP checkThis message comes on when the ESP system is
faulty.
ABS check This message comes on when the ABS system is
faulty.
Engine oil level
checkThis message comes on when the engine oil level is
low. Pin No. Message Operating condition

06-38
Overhead console switch
6. OVERHEAD CONSOLE SWITCH
The front room lamp is controlled by the BCM.
The front room lamp comes on when opening the driver or passenger door. (door coupled operation
switch ON)
When closing the driver or passenger door, the front room lamp comes on for 2 seconds and then
dims down for 3 seconds. (door coupled operation switch ON)
The front room lamp turns on/off depending on the operation of the front room lamp ON/OFF switch
(spot switch). -
-
-
-
Front room lamp switch
Door coupled operation switch
Sunroof switch
Front room lamp connector
Sunroof connector

06-398510-00
Front room lamp switch
The driver/passenger room lamps turns on
when pressing in these switches.Door coupled operation switch
The front room lamp and center room
lamp come on when opening a door with
this switch pressed in.
Sunroof switch
Push up the switch briefly: 2-step auto sliding open ▶
Push up and hold the switch: manual sliding open ▶When pushing up the switch briefly, the sunroof is automatically opened. Opening is carried
out in 2 steps. In first step, the area 5 cm behind the sunroof is not opened. Push up the switch
once again in order to open the sunroof completely. The sunroof operation stops if you
operate the switch during its operation.
The sunroof is opened as long as pushing up the switch.
Pull down the switch briefly: auto sliding close ▶
Pull down and hold the switch: manual sliding close ▶When pulling down the switch briefly, the sunroof is automatically closed. To stop the closing
sunroof, operate the switch to either direction.
The sunroof is closed as long as pulling down the switch.

06-418510-00
Sunroof warning control ▶
When removing the ignition key with the sunroof open (without SKM) or when opening the driver door
with IGN OFF or ACC and sunroof open (with SKM), the indoor buzzer sounds for 10 seconds with
the interval of 0.02s ON/1.58s OFF.
When opening and closing the driver door or closing the sunroof during indoor buzzer operation, the
buzzer stops its operation immediately.
When closing the driver door or sunroof and opening again during warning operation, the sunroof
warning does not work. If the condition is met after the ignition switch is turned to "ON" position again,
the indoor buzzer sounds for 10 seconds with the interval of 0.02s ON/1.58s OFF.
The sunroof warning has a priority over the tail lamp ON warning. 1.
2.
3.
4.

02-38810-00
1. SPECIFICATIONS
Operating voltage 9 to 16 V
System diagnosis and SDM self diagnosis voltage 9 to 16 V
Ignition voltage for side air bag and pretensioner 9 to 16 V
Communication voltage for front impact sensor 9 to 16 V
Communication voltage for side impact sensor 9 to 16 V
Operating temperature -40℃ ~ 85℃
Storage temperature -40℃ ~ 90℃
Ignition temperature -30℃ ~ 85℃
Overvoltage protection 24 V
2. MAJOR REPLACEMENT PARTS AFTER AIR BAG
DEPLOYMENT
A. In Case Of Front Air Bag Deployment
Air bag unit and its wirings (including connectors), seat belt pretensioner and its wirings (including
connectors), all front air bags, instrument panel, front impact sensor and other damaged components
B. In Case Of Curtain Air Bag Deployment
Deployed curtain air bag, air bag unit and its wiring (including connector), impact G sensor assembly for
curtain air bag, damaged trim, seat and roof headlining

04-37340-00
1. SPECIFICATIONS
2. CAUTIONS WHEN WORKING
Wear clean work clothes and gloves.
Replace and wash the gloves frequently.
Any unauthorized modification or operational test is not allowed since the sunroof motor and control
unit are preset at the factory.
You can use basic tools, e.g. a 25T/10T star screwdriver, flat-bladed and cross-tip screwdrivers. Do
not use any similar tool.
Take care not to drop the sunroof assembly when removing it and do not keep it right up. 1.
2.
3.
4.
5.
Operating voltage 9 to 16 V
Operating current (open & close) Max. 6 A
At no load Approx. 3 A
Leakage current Max. 1 mA or less
Roof motor operating speed
(at opening and closing)1.4 ± 0.5 sec./100 mm
Motor overload stop conditionsCurrent for 25 A or higher and torque (load) for 7.5 Nm
or higher
2-step opening amount1st step sliding open: 370 ± 5 mm
2nd step sliding open: 450 ± 5 mm
Vertical/horizontal tolerance for
sunroof glass panel± 2 mm

04-4
Sunroof switch
1. SYSTEM LAYOUT
Sunroof assembly
TILTOPEN
Sunroof motor &
control unit

04-57340-00
2. OPERATING PROCESS
1) Sunroof Switch
This can be closed or open manually to block sunlight when the sunroof function is not in use. The sunroof glass can be open in two steps and can be tilted by the switch operation. The sunroof switches are included in the overhead console switches and consists of the TILT,
CLOSE and OPEN switches.
TILT
CLOSE
OPEN ▷
▷
▷
Sun shade panel Sunroof glass Sunroof switch ▶
Opens only rear section of the sunroof.
Closes the sunroof.
Opens the sunroof.
Sunroof glass ▶
Sun shade panel ▶