2012 SSANGYONG KORANDO Bearing

02-4
2. TIGHTENING TORQUE
Name Size Quantity Tightening torque
Heater core screw bolt - 170 ± 7 Nm
Ladder frame bolt M8 X 1.25 X 20 725 ± 2.5 Nm
TGCC M6 X 1.0 X 25 1010 ± 1.0 Nm
Oil drain plug - 130 ± 3.0 Nm
Oil pan bolt M6 X 1.0 X 20 1610 ± 1.0 Nm
Oil pan bolt M6 X 1.0 X 35 410 ± 1.0 Nm
Oil pan bolt M6 X 1.0 X 85 210 ± 1.0 Nm
Oil dipstick gauge bolt M6 X 1.0 X 16 110 ± 1.0 Nm
Camshaft cap M6 X 1.0 X 30 2010 ± 1.0 Nm
Main gallery screw bolt - 155 ± 5.5 Nm
Main bearing cap bolt - 1055 Nm + 90°
Cylinder head bolt M12X1.75X102 1055 Nm + 180°
Cylinder head TGCC side bolt M8 X 1.25 X 30 425 ± 2.5 Nm
Cylinder head front cover bolt M6 X 1.0 X 25 810 ± 1.0 Nm
Cylinder head cover bolt M6 X 1.0 X 30 2010 ± 1.0 Nm
Crankshaft center bolt M18 X 1.5 X 50 1200 ± 20 Nm
90 ° + 10 °
Flywheel bolt M10 X 1.0 X 22 845 ± 5 Nm
90 ° + 10 °
Connecting rod bolt M9 X 1.0 X 52 8 40 + 5 Nm
90 ° + 10 °
Cam Cap bolt (#1) M6 X 1.0 X 35 410 ± 1.0 Nm
Cam Cap bolt (#2~5) M6 X 1.0 X 30 1610 ± 1.0 Nm
Solenoid valve bolt M5 X 0.8 X 22 18 ± 1 Nm
Intake manifold bolt M8 X 1.25 X 32 525 ± 2.5 Nm

02-331130-25
Components
Overview ▶
Connecting rod converts the reciprocating movement of piston to the rotating movement of crankshaft.
The big end is connected to connecting rod bearing and the crank pin journal, and the small end is
connected to the piston pin.
Components ▶
Connecting rod
Piston pin bush
Connecting rod
Connecting rod upper bearing
Connecting rod lower bearing
Connecting rod cap
Connecting rod cap bolt A.
B.
C.
D.
E.
F.

02-34
Selection of connecting rod bearing ▶
Select the bearing shell combination according to the table below:
Conrod_UPR
GradeConrod_LWR
GradeClearance
Red Blue 0.005 ~ 0.050
Yellow Yellow 0.005 ~ 0.050
Blue Red 0.005 ~ 0.050

02-36
Bottom of cylinder block Crankshaft sprocket installing surface
Crankshaft lower bearing Crankshaft lower bearing
Selection of crankshaft main bearing ▶
핀 펀치 마크별 베어링 선택
Pin
punch
markColorDiameter of crankshaft
main journal in cylinder
block (mm)
* Blue 62.500 ~ 62.506
** Yellow 62.506 ~ 62.513
*** Red 62.513 ~ 62.519
Mark ColorDiameter of
crankshaft main
journal (mm)
B Blue 57.960 ~ 57.965
Y Yellow 57.955 ~ 57.960
R Red 57.950 ~ 57.955
W White 57.945 ~ 57.950
V Violet 57.940 ~ 57.945
Engine
name
Main
journal
bearing
#1 #2 #3 #4 #5
G2 0DF
RRWWR

02-38
Engine oil
Coolant
Coolant and oil flows ▶
Cylinder head
Cylinder block water
jacket
Coolant pumpCoolant pipe
Thermostat
Supply line to cylinder head
Oil pumpSupply line to PCJ
Main bearing
Oil filter assembly

07-71535-01
Oil pressure switch
1. OVERVIEW
The lubrication system supplies oil to each lubrication section to prevent friction and wear and to remove
heat from the friction part. As the engine runs, frictional heat is generated on each lubrication section. If
this condition persists, the bearing can be burned and stuck.
In other words, it creates an oil film on each sliding surface to convert solid friction to liquid friction in
order to minimize wear and prevent temperature increasing on the friction part.
2. COMPONENTS
Engine oil dipstickOil jet
Engine oil panOil pumpOil filter module

07-8
1) Operation Flow
3. OPERATING PROCESS
CVVT
Cam journal
bearing
Main oil gallery
in cylinder block
Oil pressure
switch
Oil filter assembly
Oil supply Oil pump Main journal bearingChain
tensioner
Oil jet

05-33310-02
1. SPECIFICATION
Description Specification
Structure 2-piece type with CV joint, spider, and rubber
coupling
Weight below 12.0 kg
Joint type CV joint, spider, rubber coupling
Spider Numbers one (installed on center bearing side)
External diameterØ24 mm
Overall sizeØ62.5 mm
Dimension
(Length x Dia.)No.1 shaft (TM to spider)1,069 x Ø60 mm
No. 2 shaft (spider to axle)847.5 x Ø60 mm
Runout of tube (after installation) 0.3 mm
Unbalance 80g.mm @ 3,000rpm
(second measurement: 120 g.mm)
U-joint Starting torque 0.3 to 0.7 Nm
Minimum starting angle18˚
Amount of grease in CV joint 210+-10g
2. TIGHTENING TORQUE
Fastener Tightening torque
Bolt/nut for rubber coupling (rear axle side) 39.2 to 49.0 Nm
Bolt/nut for CV joint (transaxle side) 29.4 to 39.2 Nm
Mounting bolt for center bearing 58.8 to 68.6 Nm