Changing light bulbs for fog lights
Fig. 130
Front bumper: Protective grille/removing the fog light Fig. 131
Replacing the light bulb
First read and observe the introductory information and safety warn-
ings on page 159.
Removing the protective grille
›
Remove the protective grille by inserting the clamp for removing the wheel
trims at the location » Fig. 130 - indicated by the arrow » page 145, Vehicle
tool kit .
› Remove the protective grille in the direction of the arrow
» Fig. 130.
Changing light bulbs for fog lights
› Use the screwdriver from the tool kit to unscrew the fog lamp
» Fig. 130 -
.
› Remove the fog lamp in the direction of the arrow.
› Remove the connector.
› Turn the bulb holder A
» Fig. 131 in an anti-clockwise
direction up to the stop
and remove.
ä ›
Insert the bulb holder into the lamp and turn in a
clockwise direction as far as
the stop.
› Fit the connector.
› Replace the fog lamp by inserting it in the opposite direction of the ar-
row » Fig. 130 - and tighten.
› Insert the protective grille and carefully press it in. The protective grille must
engage firmly. Ð Changing the bulb for the licence plate light
Fig. 132
Remove the number plate light/replace the bulb
First read and observe the introductory information and safety warn-
ings on page 159.
›
Open the boot lid.
› Insert a flat screwdriver at the location indicated by the arrow
» Fig. 132 - ,
press it in lightly, and unlatch the springs.
› Remove the lamp.
› Pull the faulty bulb out of the holder in the direction of the arrow
» Fig. 132 - .
› Insert a new bulb into the holder.
› Replace the lamp and lightly press it until the spring latches. Ð
ä
162 Do-it-yourself
Tail lamp assembly
Fig. 133
Removing the cover of the lamp/removing the lamp Fig. 134
Installing the lamp connector/lamp
First read and observe the introductory information and safety warn-
ings on page 159.
Removing the tail lamp assembly
›
Open the boot lid.
› Insert the clamp for removing the wheel trims
» page 145, Vehicle tool kit into
the hole indicated by the arrow » Fig. 133 - .
› Remove the cover in the direction of the arrow.
› Use the screwdriver from the tool kit
» Fig. 133 - to unscrew the lamp.
› Grip the tail lamp assembly and carefully remove it by pulling it back at an angle
with loosening movements.
› Pull the locking mechanism 1
» Fig. 134 on the connector in the direction of
the arrow.
› Press the locking mechanism 2
» Fig. 134 and remove the connector.
ä Installing the tail lamp assembly
› Insert the connector into the lamp and lock it securely.
› Carefully press the tail lamp assembly into the bodywork so that the bolts 2
» Fig. 135 on page 163 latch with the mounts in the body
» Fig. 134 - .
› Screw the tail lamp into place and install the cover. Ensure that the cover en-
gages firmly. Ð Replacing the bulbs in the tail lamp assembly
Fig. 135
Outer part of the lamp/inner part of the lamp
First read and observe the introductory information and safety warn-
ings on page 159.
Changing the bulb in the outer part of the lamp
›
Turn the bulb holder 1
» Fig. 135 anti-clockwise
remove it from the lamp hous-
ing.
› Replace the bulb, insert the holder with the bulb into the lamp housing and
turn in a clockwise direction to the stop.
Changing the bulb in the inner part of the lamp
› Unlock the bulb holder using the locking latches
» Fig. 135 - and remove the
holder from the tail lamp.
› Turn the bulb holder
anti-clockwise up to the stop and remove it from the lamp
housing » Fig. 135 - .
› Replace the bulb, insert the holder with the bulb into the lamp housing and
turn in a clockwise direction to the stop.
› Insert the bulb holder in the tail lamp assembly. All locking mechanisms must
audibly snap into place. Ð
ä
163
Fuses and light bulbs
