2012 SKODA RAPID light

No. Power consumer
29 Injection, coolant pump
30 Fuel pump, ignition system, cruise control 31 Lambda probe
32 High pressure fuel pump, pressure valve
33 Engine control unit
34 Engine control unit, vacuum pump
35 Switch illumination, number plate light, parking light, headlamp washer
system
36 Main beam 37 Rear fog light, DC-DC converter
38 Fog lights 39 Air blower for heating
40 Not assigned 41 Heated front seats
42 Rear window heater
43 Horn
44 Windscreen wipers 45 Boot lid lock, central locking system
46 Alarm 47 Cigarette lighter, power socket in the luggage compartment
48 ABS 49 Turn signal lights, brake lights50 DC-DC converter, radio 51 Electric windows (driver's window and rear left window)
52 Electric windows (front passenger's window and rear right)
53 Windscreen washer
54 START-STOP instrument cluster, steering wheel module, multi-function
steering wheel
55 Control unit for automatic gearbox
56 Headlight cleaning system 57 Low beam on the left
58 Low beam on the right Ð Fuses in the engine compartment
Fig. 123
Schematic representation of fuse box in engine compartment: Ver-
sion
1/version 2
First read and observe the introductory information and safety warn-
ings on page 156.
Fuse assignment in engine compartment
No. Power consumer
1 Generator
2 Not assigned
3 Vehicle interior (variant 1) » Fig. 123 Power supply for fuse block (variant
2) » Fig. 123
4 Electric auxiliary heater (variant 1) » Fig. 123 Vehicle interior (variant
2) » Fig. 123
5 Interior
6 Engine cooling fan, control unit for preheating unit 7 Electrohydraulic power steering
8 ABS 9 Radiator fan
10 Automatic gearbox 11 ABS
12 Central control unit
13 Electrical auxiliary heating system £ ä
158 Do-it-yourself

Note
Fuses 1 - 7 are replaced by a specialist ŠKODA garage. ÐReplacing the fuses in the engine compartment
Fig. 124
Vehicle battery: Cover for the fuse box (variant 1) Fig. 125
Vehicle battery: Cover for the fuse box (variant 2)
First read and observe the introductory information and safety warn-
ings on page 156.
›
Press together the interlocks of the cover simultaneously in the direction of the
arrow 1
» Fig. 124.
› Push the cover in the direction of the arrow 2
.
› Use a flat screwdriver to release the fixtures in the openings 3
.
› Lift the cover upwards in the direction of the arrow 4
.
Ð
ä Bulbs
ä
Introduction
This chapter contains information on the following subjects:
Headlights 160
Changing the bulb for the low beam 160
Changing the bulb for main beam, separate daytime running lights, and
parking light 161
Changing the bulb for the front turn signal light 161
Changing light bulbs for fog lights 162
Changing the bulb for the licence plate light 162
Tail lamp assembly 163
Replacing the bulbs in the tail lamp assembly 163
Some manual skills are required to change a bulb. For this reason, if uncertain, we
recommend that bulbs are replaced by a ŠKODA specialist garage or other expert
help is sought.
› Switch off the ignition and all of the lights before replacing a bulb.
› Faulty bulbs must only be replaced with the same type of bulbs. The designa-
tion is located on the light socket or the glass bulb.
› A stowage compartment for replacement bulbs is located in a plastic box in the
spare wheel or underneath the floor covering in the boot. WARNING
■ Accidents can be caused if the road in front of the vehicle is not sufficiently
illuminated and the vehicle cannot or can only be seen with difficulty by other
road users.
■ Always read and observe the warnings before completing any work in the
engine compartment »

page 126, Engine compartment .
■ Bulbs H7 and H15 are pressurised and may burst when changing the bulb -
risk of injury! We therefore recommended wearing gloves and safety glasses
when changing a bulb. £
159
Fuses and light bulbs

CAUTION
■ Do not take hold of the glass bulb with naked fingers (even the smallest
amount of dirt reduces the working life of the light bulb). Use a clean cloth, nap-
kin, or similar. ■ When removing and installing the tail light make sure that the paintwork of the
vehicle and the tail light are not damaged. Note
■ This Owner's Manual only describes the replacement of bulbs where it is possi-
ble to replace the bulbs on your own without any complications arising. Other
light bulbs should be changed by a
ŠKODA specialist garage.
■ We recommend that a box of replacement bulbs be always carried in the vehi-
cle. Replacement bulbs can be purchased from
ŠKODAOriginal Accessories.
■ We recommend that the headlight settings are checked by a ŠKODA specialist
garage after replacing a bulb in the main or low beam.
■ LED diodes should be changed by a specialist ŠKODA garage. ÐHeadlights
Fig. 126
Bulb arrangement: Halogen
headlight
First read and observe the introductory information and safety warn-
ings on page 159.
Bulb arrangement in the Halogen headlamp
Low beam
Main beam, separate daytime running lights, and parking light
Turn signal light (at the front) Ð
ä A
B
C Changing the bulb for the low beam
Fig. 127
Changing the bulb for the low
beam
First read and observe the introductory information and safety warn-
ings on page 159.
›
Remove the rubber cover A
» Fig. 126 on page 160

» page 160.
› Remove the connector with the bulb by pulling it back in the direction of the
arrow with loosening movements »
Fig. 127.
› Remove the connector.
› Insert a new light bulb in such a way that the fixing lugs of the bulb fit in the
recesses of the reflector.
› Fit the connector.
› Insert the rubber cover. Ð
ä
160 Do-it-yourself

Changing the bulb for main beam, separate daytime running
lights, and parking light
Fig. 128
Changing the bulb for main beam, separate daytime running lights,
and parking light
First read and observe the introductory information and safety warn-
ings on page 159.
Removing and replacing the bulb for main beam and separate daytime running
lights
›
Remove the rubber cover B
» Fig. 126 on page 160
» page 160.
› Turn the bulb holder A
» Fig. 128 anti-clockwise
up to the stop and remove.
› Replace the bulb, insert the bulb holder with the new bulb and turn in a
clock-
wise direction to the stop.
› Insert the rubber cover.
Removing and replacing the bulb for the parking light
› Remove the rubber cover B
» Fig. 126 on page 160

» page 160.
› Remove the socket C
» Fig. 128
together with the bulb with loosening move-
ments.
› Remove the faulty bulb from the bulb holder C
in the direction of the arrow.
› Insert a new bulb in the bulb holder up to the stop.
› Replace the bulb holder in the headlamp with the bulb.
› Insert the rubber cover. Ð
ä Changing the bulb for the front turn signal light
Fig. 129
Changing the bulb for the turn
signal light
First read and observe the introductory information and safety warn-
ings on page 159.
›
Turn the socket with the bulb
» Fig. 129 anti-clockwise up to the stop and re-
move.
› Replace the bulb, insert the socket with the new bulb and turn
clockwise up to
the stop. Ð
ä
161
Fuses and light bulbs

Changing light bulbs for fog lights
Fig. 130
Front bumper: Protective grille/removing the fog light Fig. 131
Replacing the light bulb
First read and observe the introductory information and safety warn-
ings on page 159.
Removing the protective grille
›
Remove the protective grille by inserting the clamp for removing the wheel
trims at the location » Fig. 130 -  indicated by the arrow » page 145, Vehicle
tool kit .
› Remove the protective grille in the direction of the arrow
» Fig. 130.
Changing light bulbs for fog lights
› Use the screwdriver from the tool kit to unscrew the fog lamp
» Fig. 130 -
.
› Remove the fog lamp in the direction of the arrow.
› Remove the connector.
› Turn the bulb holder A
» Fig. 131 in an anti-clockwise
direction up to the stop
and remove.
ä ›
Insert the bulb holder into the lamp and turn in a
clockwise direction as far as
the stop.
› Fit the connector.
› Replace the fog lamp by inserting it in the opposite direction of the ar-
row » Fig. 130 -  and tighten.
› Insert the protective grille and carefully press it in. The protective grille must
engage firmly. Ð Changing the bulb for the licence plate light
Fig. 132
Remove the number plate light/replace the bulb
First read and observe the introductory information and safety warn-
ings on page 159.
›
Open the boot lid.
› Insert a flat screwdriver at the location indicated by the arrow
» Fig. 132 - ,
press it in lightly, and unlatch the springs.
› Remove the lamp.
› Pull the faulty bulb out of the holder in the direction of the arrow
» Fig. 132 -  .
› Insert a new bulb into the holder.
› Replace the lamp and lightly press it until the spring latches. Ð
ä
162 Do-it-yourself

Tail lamp assembly
Fig. 133
Removing the cover of the lamp/removing the lamp Fig. 134
Installing the lamp connector/lamp
First read and observe the introductory information and safety warn-
ings on page 159.
Removing the tail lamp assembly
›
Open the boot lid.
› Insert the clamp for removing the wheel trims
» page 145, Vehicle tool kit into
the hole indicated by the arrow » Fig. 133 - .
› Remove the cover in the direction of the arrow.
› Use the screwdriver from the tool kit
» Fig. 133 -  to unscrew the lamp.
› Grip the tail lamp assembly and carefully remove it by pulling it back at an angle
with loosening movements.
› Pull the locking mechanism 1
» Fig. 134 on the connector in the direction of
the arrow.
› Press the locking mechanism 2
» Fig. 134 and remove the connector.
ä Installing the tail lamp assembly
› Insert the connector into the lamp and lock it securely.
› Carefully press the tail lamp assembly into the bodywork so that the bolts 2
» Fig. 135 on page 163 latch with the mounts in the body
» Fig. 134 - .
› Screw the tail lamp into place and install the cover. Ensure that the cover en-
gages firmly. Ð Replacing the bulbs in the tail lamp assembly
Fig. 135
Outer part of the lamp/inner part of the lamp
First read and observe the introductory information and safety warn-
ings on page 159.
Changing the bulb in the outer part of the lamp
›
Turn the bulb holder 1
» Fig. 135 anti-clockwise
remove it from the lamp hous-
ing.
› Replace the bulb, insert the holder with the bulb into the lamp housing and
turn in a clockwise direction to the stop.
Changing the bulb in the inner part of the lamp
› Unlock the bulb holder using the locking latches
» Fig. 135 -  and remove the
holder from the tail lamp.
› Turn the bulb holder
anti-clockwise up to the stop and remove it from the lamp
housing » Fig. 135 - .
› Replace the bulb, insert the holder with the bulb into the lamp housing and
turn in a clockwise direction to the stop.
› Insert the bulb holder in the tail lamp assembly. All locking mechanisms must
audibly snap into place. Ð
ä
163
Fuses and light bulbs

Index
A
ABS 73
Warning light 20
Accessories 144
Adjusting Exterior mirror 42
Adjusting seats 92
Adjustment Seat 45
Aerial 118
see Radio reception 120
Airbag 99
Deployment 99
Front airbag 100
Head airbag 102
Side airbag 101
Airbag system 99
Air conditioning system Air outlet vents 60
Climatronic 65
Manual air conditioning system 62
Alarm 29
Anti-theft alarm system 29
Antilock brake system 73
Armrest 45
rear 48
Ashtray 53
ASR 73
Assist systems ABS 20, 73
ASR 73
Cruise control systems (CCS) 75
EDL 73
ESC 19, 72
Parking aid 74START/STOP 77
TCS 20
Auto Check Control 16
Automatic gearbox 79
Dynamic shift programme 82
Emergency programme 82
Information for driving 79
Kickdown 82
Manual shifting of gears 81
Parking 80
Selector lever-emergency unlocking 83
Selector lever lock 81
Selector lever positions 80
Starting off 80
Stopping 80
Tiptronic 81
Automatic load deactivation 136
AUX-IN 90
Avoiding damage to your vehicle 113
B
Before setting off 91
Belts 95
Belt tensioners 98
Bonnet Closing 128
Opening 128
Boot Class
N1 vehicles 49
Cover 50
Emergency unlocking 31
Fastening elements 49
Fixing nets 50
Hooks 50
Light 49
see Boot lid 31
Unlocking the boot lid 31
Boot lid 31
Automatic locking 31
Brake assist 72Brake booster 72
Brake fluid Checking 132
Brakes Brake booster 72
Handbrake 72
Running in 109
Warning light 17
Braking Brake fluid 132
Breakdown kit 149
Bulbs Replacing 159
Button in the driver's door Electrical power windows 31
C
Car computer see Multifunction display 11
Car jack 145
Carrier 51
Catalytic converter 109
Central locking button 27
Central locking system 25
lock 27
unlock 26
Changes 144
Changing Engine oil 130
Wheel 146
Charging a vehicle battery 135
Checking Battery electrolyte level 135
Brake fluid 132
Coolant level 130
Engine oil 129
Oil level 129
Windscreen washer fluid 132
Children and safety 105
170 Index

Child safety
Side airbag 106
Child safety lock 25
Child seat Classification 106
ISOFIX 107
on the front passenger seat 105
Suitability 107
TOP TETHER 108
Chrome parts refer to Taking care of your vehicle 119
Cigarette lighter 53
Cleaning 117
Artificial leather 122
Headlight lenses 120
Material coverings 122
Materials 122
Natural leather 122
Plastic parts 119
Wheels 121
Climatronic Recirculated air mode 66
Clock 11
Clothes hooks 58
Cockpit 12-volt power socket 54
Ashtray 53
Cigarette lighter 53
General view 7
Light 38
Storage compartments 54
Compartments 54
Computer see Multifunction display 11
Coolant Checking 130
Replenishing 131
Temperature gauge 9
Warning light 19
Correct seated position 92
Counter for distance driven 10Cruise control system (CCS) 75
Cup holder front 52
rear 53
D
DAY LIGHT see Daytime running lights 35
Daytime running lights 35
Deactivating an airbag 103
Defrsoting rear window 39
Delayed locking of the boot lid see Boot lid 31
Diesel refer to Fuel 126
Diesel fuel Operation in winter 126
Diesel particulate filter 21
Digital clock 11
Dipstick 129
Display Coolant temperature 9
Fuel gauge 9
Service interval 10
Distance driven 10
Door Child safety lock 25
Doors Emergency locking 30
Driving Abroad 113
Driving through water on the street 114
Emissions 164
Fuel consumption 164
Maximum speed 167
E
Economical and environmentally friendly driving 110EDL 73
Electrical power windows Button in the driver's door 31, 32
Button in the rear door 32
Electronic differential lock 73
Electronic immobiliser 69
Emergency Automatic gearbox 82
Changing a wheel 146
Hazard warning light system 37
Jump-starting 152
locking of the doors 30
Selector lever-unlocking 83
Towing the vehicle 153
Tyre repair 149
Unlocking the boot lid 31
Emissions 164
Engine Running in 109
Starting engine 70
Switching off the engine 70
Engine compartment Brake fluid 132
Coolant 130
Overview 128
Vehicle battery 133
Engine oil Capacity 166
Changing 130
Checking 129
Replenishing 129
Specification 166
Warning light 18
Engine revolutions counter 9
Environment 110
Environmental compatibility 112
Environmentally friendly driving 110
ESC 72
Warning light 19
171
Index