2012 RENAULT SCENIC programming

13B-227
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF647
CONTINUED 1
1.DEF
2.DEFNOTESNone.
Check the condition of the EGR valve (see Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2,
Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1460 or 169).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3EL and 3JM of component 1460 or 169.
If the resistance of the EGR valve is not between 1 kΩ < X < 7,5 kΩ, replace the EGR valve.
Measure the resistance between connections 3EL and 3GC of component 1460 or 169.
If the resistance of the EGR valve is not between 3.9 kΩ < X < 12.6 kΩ, replace the EGR valve.
After replacement, run command SC036 Reinitialise programming and select EGR valve to reinitialise the EGR
valve offsets.
Check the continuity and absence of interference resistance of the following connections:
•3GC between components 120 and 1460 or 169,
•3EL between components 120 and 1460 or 169,
•3JM between components 120 and 1460 or 169.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring.
Remove and clean the EGR valve, then refit the EGR valve and start the engine (see MR364 (Mégane II ph2),
MR370 (Scénic II ph2), MR 395 (Laguna II ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2), Mechanical, 14A,
Emission control, Exhaust gas recirculation solenoid valve: Removal - Refitting).
If the fault is still present, replace the EGR valve then run command SC036 Reinitialise programming and select
EGR valve to reinitialise the EGR valve offsets.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-254
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF899
PRESENT
OR
STOREDREGENERATION TEMPERATURE LIMIT EXCEEDED
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present during an After-Sales regeneration, if the temperature
threshold is exceeded.
Special notes:
If the fault is present:
– regeneration in progress is stopped.
IMPORTANT: The fault appears if the temperature threshold is exceeded during
the After-Sales regeneration phase.
• Carry out particle filter replacement
• run command SC036 Reinitialise programming (see Interpretation of commands) and select After particle
filter replacement.
•switch off the ignition and wait for the diagnostic tool message (maximum wait 8 minutes): Loss of
dialogue with the computer: EDC16 CP33, check the tool connection and the computer supply voltage,
• then switch on the ignition again,
•clear the present or stored faults from the computer memory (operation to be carried out within 3 minutes
of switching on the ignition).
If the fault is still present, contact the Techline.
EDC16CP33_V18_DF899 / EDC16CP33_V1C_DF899 / EDC16CP33_V54_DF899 / EDC16CP33_V20_DF899 / EDC16CP33_V58_DF899 /
EDC16CP33_V5C_DF899 / EDC16CP33_V24_DF899 / EDC16CP33_V28_DF899 / EDC16CP33_V62_DF899 / EDC16CP33_V26_DF899 /
EDC16CP33_V60_DF899
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-258
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF1069
PRESENT
OR
STOREDHEATER PLUGS NOT CONFIGURED
1.DEF: Configuration / Initialisation
NOTESSpecial notes:
If the fault is present:
– engine torque limited,
– an engine speed below 1500 rpm.
The level 1 warning light is illuminated.
Conditions under which the fault appears:
This fault only appears when the computer is reprogrammed after a change of Vdiag.
If the fault is present, display status ET781 Heater plugs in the sub-function Ignition/Preheating.
If status ET781 is STATUS 3, this means that the heater plugs are not configured in the injection computer.
To find out which type of heater plugs are fitted to the engine, look at the colour of the rings on the plugs.
– Slow plugs have a black ring.
– Fast plugs have a white ring.
To configure the type of plugs, run command SC036 Reinitialise programming and select HEATER PLUGS (see
Interpretation of commands).
If the fault is stored, clear the fault.
End of fault finding.
If the fault is still present or if status ET781 is not STATUS 3 or is inconsistent with the type of plug fitted, contact
the Techline.
EDC16CP33_V20_DF1069 / EDC16CP33_V24_DF1069 / EDC16CP33_V04_DF1069 / EDC16CP33_V08_DF1069 /
EDC16CP33_V44_DF1069 / EDC16CP33_V4C_DF1069 / EDC16CP33_V34_DF1069 / EDC16CP33_V38_DF1069 /
EDC16CP33_V74_DF1069 / EDC16CP33_V60_DF1069 / EDC16CP33_V62_DF1069
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 20, 24,
34, 38, 44, 4C, 60, 62, 74

13B-262V12 MR-372-J84-13B300$090.mif
13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Tool status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET007Pre-postheating control
ET024Thermoplunger no. 1 request
ET025Thermoplunger no. 2 request
ET026Thermoplunger no. 3 request
ET034Clutch signal registered
ET038Engine
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET079Air conditioning present
ET104Injector code use
ET120Pre-postheating signal
ET143Low-speed fan assembly relay control
ET144High-speed fan assembly relay control
ET205Thermoplunger no. 1 relay control (only on Laguna II ph2 without particle filter)
ET206Thermoplunger no. 2 relay control (only on Laguna II ph2 without particle filter)
ET207Thermoplunger no. 3 relay control (only on Laguna II ph2 without particle filter)
ET238Synchronisation
ET285Injection -> automatic gearbox connection
ET341Immobiliser code programmed
ET405Clutch pedal switch (only for manual gearboxes)
ET415Cruise control/Speed limiter deactivation
ET587Cooling of recirculated exhaust gas
ET589Electric coolant pump control (turbocharger)
ET615Automatic gearbox lever position
ET651EGR programming cut-off
DIESEL INJECTION
Fault finding – Status summary table

13B-264V12 MR-372-J84-13B300$101.mif
13B
ET001COMPUTER + AFTER IGNITION FEED
STATUS
DEFINITIONPRESENT: This status indicates that the + after ignition feed is active.
ABSENT: This status indicates that the + after ignition feed is not active.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"PRESENT"Ignition on and engine running warm at idle speed with the + after ignition feed
activated.
Normal operating condition.
The computer is correctly supplied after the ignition has been switched on.
In the event of a fault, refer to the interpretation of DF046 Battery voltage or DF151
Main relay circuit.
Sensor electrical conformity.
"ABSENT"
NOTESIgnition on
DIESEL INJECTION
Fault finding – Interpretation of statuses
EDC16CP33_V18_ET001 / EDC16CP33_V1C_ET001 / EDC16CP33_V54_ET001 / EDC16CP33_V20_ET001 / EDC16CP33_V58_ET001 /
EDC16CP33_V5C_ET001 / EDC16CP33_V24_ET001 / EDC16CP33_V04_ET001 / EDC16CP33_V08_ET001 / EDC16CP33_V44_ET001 /
EDC16CP33_V4C_ET001 / EDC16CP33_V34_ET001 / EDC16CP33_V38_ET001 / EDC16CP33_V74_ET001 / EDC16CP33_V28_ET001 /
EDC16CP33_V62_ET001 / EDC16CP33_V26_ET001 / EDC16CP33_V60_ET001
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-266V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET003ENGINE IMMOBILISER
STATUS
DEFINITIONACTIVE: This status indicates that the immobiliser is active.
INACTIVE: This status indicates that the immobiliser is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
ACTIVERefer to the fault finding note for the UCH (see 87B, Passenger compartment
connection unit).
INACTIVERefer to the fault finding note for the UCH (see 87B, Passenger compartment
connection unit).
EDC16CP33_V18_ET003 / EDC16CP33_V1C_ET003 / EDC16CP33_V54_ET003 / EDC16CP33_V20_ET003 / EDC16CP33_V58_ET003 /
EDC16CP33_V5C_ET003 / EDC16CP33_V24_ET003 / EDC16CP33_V04_ET003 / EDC16CP33_V08_ET003 / EDC16CP33_V44_ET003 /
EDC16CP33_V4C_ET003 / EDC16CP33_V34_ET003 / EDC16CP33_V38_ET003 / EDC16CP33_V74_ET003 / EDC16CP33_V28_ET003 /
EDC16CP33_V62_ET003 / EDC16CP33_V26_ET003 / EDC16CP33_V60_ET003
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-270V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET034CLUTCH SIGNAL DETECTED
STATUS
DEFINITIONNO: This status indicates that the clutch pedal has not been depressed since
the ignition was switched on.
YES: This status indicates that the clutch pedal has been depressed since the
ignition was switched on.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NOWhen the vehicle ignition is switched on without depressing the clutch pedal,
statusET034 is NO.
EDC16CP33_V18_ET034 / EDC16CP33_V1C_ET034 / EDC16CP33_V54_ET034 / EDC16CP33_V20_ET034 / EDC16CP33_V58_ET034 /
EDC16CP33_V5C_ET034 / EDC16CP33_V24_ET034 / EDC16CP33_V04_ET034 / EDC16CP33_V08_ET034 / EDC16CP33_V44_ET034 /
EDC16CP33_V4C_ET034 / EDC16CP33_V34_ET034 / EDC16CP33_V38_ET034 / EDC16CP33_V74_ET034 / EDC16CP33_V28_ET034 /
EDC16CP33_V62_ET034 / EDC16CP33_V26_ET001 / EDC16CP33_V60_ET001
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-273V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042CRUISE CONTROL/SPEED LIMITER
STATUS
DEFINITIONNOT DETECTED: This status indicates that the cruise control or speed limiter function
is not present on the vehicle.
INACTIVE: This status indicates that the main on/off switch of the cruise control/speed
limiter is in the rest (or neutral) position.
LIMITER: This status indicates that the driver has used the main switch to select the
speed limiter.
CRUISE CONTROL: This status indicates that the driver has used the main switch to
select the cruise control.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NOT DETECTEDThe cruise control or speed limiter function is not present on the vehicle.
INACTIVENo button has been pressed.
LIMITERThe speed limiter ON/OFF button has been pressed.
Lights the orange warning light on the instrument panel.
CRUISE
CONTROLThe cruise control ON/OFF button has been pressed.
Lights the green warning light on the instrument panel.
EDC16CP33_V18_ET042 / EDC16CP33_V1C_ET042 / EDC16CP33_V54_ET042 / EDC16CP33_V20_ET042 / EDC16CP33_V58_ET042 /
EDC16CP33_V5C_ET042 / EDC16CP33_V24_ET042 / EDC16CP33_V04_ET042 / EDC16CP33_V08_ET042 / EDC16CP33_V44_ET042 /
EDC16CP33_V4C_ET042 / EDC16CP33_V34_ET042 / EDC16CP33_V38_ET042 / EDC16CP33_V74_ET042 / EDC16CP33_V28_ET042 /
EDC16CP33_V62_ET042 / EDC16CP33_V26_ET042 / EDC16CP33_V60_ET042
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74