2012 RENAULT SCENIC heater

13B-448V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC064THERMOPLUNGER No. 2 RELAY
NOTESThere must be no present or stored faults.
Perform this fault finding procedure if there is a fault with the passenger compartment
heating - demisting.
Consult the "Wiring diagrams" Technical Note to locate the relevant fuses and relays.
Special notes:
The thermoplunger no. 2 relay or the additional heater interface unit supplies
thermoplungers 2 and 3 in parallel.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
If the thermoplunger no. 2 relay does not operate during command AC064.
Check the condition of the thermoplunger 2 relay mounting on the engine fuse box or the additional heater
interface unit (see Wiring Diagram Technical Note, Vehicle, component code 1068 or 1550).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Vehicle, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
if the fault is still present, check as follows that this relay is controlled by the engine management computer:
Disconnect the thermoplunger no. 2 relay, fit a 50 Ω to 100 Ω resistor on its mounting instead of the coil, and
connect a voltmeter as follows:
– positive terminal to + 12 V battery,
– negative terminal on connection 3JAA of component 1068 or 1550.
Run command AC064.
If the voltmeter shows the battery voltage (4 ON-OFF cycles of 10 seconds), replace the thermoplunger no. 2
relay.
If the voltmeter does not show the battery voltage (4 ON-OFF cycles of 10 seconds), contact the Techline.
EDC16CP33_V18_AC064 / EDC16CP33_V1C_AC064 / EDC16CP33_V54_AC064 / EDC16CP33_V20_AC064 / EDC16CP33_V58_AC064 /
EDC16CP33_V5C_AC064 / EDC16CP33_V24_AC064 / EDC16CP33_V04_AC064 / EDC16CP33_V08_AC064 / EDC16CP33_V44_AC064 /
EDC16CP33_V4C_AC064 / EDC16CP33_V34_AC064 / EDC16CP33_V38_AC064 / EDC16CP33_V74_AC064 / EDC16CP33_V28_AC064 /
EDC16CP33_V62_AC064 / EDC16CP33_V26_AC064 / EDC16CP33_V60_AC064
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-468V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
VP036INHIBIT FUEL SUPPLY
NOTESThis command enables you to disable the supply to the injectors.
This command is carried out with the engine switched off, and ignition on.
This command allows the injectors to be locked, so that starting is not possible.
Command VP036 allows the engine compressions to be checked in complete safety without disconnecting the
connectors of the injectors or the TDC sensor.
Procedure to follow (cylinder no. 1 is located on the timing end):
– Remove all of the heater plugs, connect the compression gauge with the M9R flexible end piece, part no.
MOT 1772, to a cylinder.
– Position the gear lever in neutral (manual gearbox) or to position P (automatic/sequential gearbox).
– Depress the brake pedal and keep it in this position throughout the test.
– Activate command VP036.
– Attempt to start the vehicle (within 10 seconds of activating command VP036).
If the vehicle does not start, check the cylinder compressions.
Start the procedure again on another cylinder.
WARNING:
Keep the brake pedal depressed for the length of the test.
This command is inhibited automatically after 10 seconds.
EDC16CP33_V18_VP036 / EDC16CP33_V1C_VP036 / EDC16CP33_V54_VP036 / EDC16CP33_V20_VP036 / EDC16CP33_V58_VP036 /
EDC16CP33_V5C_VP036 / EDC16CP33_V24_VP036 / EDC16CP33_V04_VP036 / EDC16CP33_V08_VP036 / EDC16CP33_V44_VP036 /
EDC16CP33_V4C_VP036 / EDC16CP33_V34_VP036 / EDC16CP33_V38_VP036 / EDC16CP33_V74_VP036 / EDC16CP33_V28_VP036 /
EDC16CP33_V62_VP036 / EDC16CP33_V26_VP036 / EDC16CP33_V60_VP036
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-473
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP2
CONTINUED 1
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the conformity of the engine earths (oxidation, tightness, etc.).
Check the mounting and condition (overheating) of the sensor.
Check the synchronisation of the camshaft sensors and the engine speed sensors with the display of ET238
Synchronisation. If synchronisation is not active, refer to the checks described in DF195 Camshaft/engine
speed sensor consistency.
Test the high pressure fuel circuit:
Run scenario SC035 High pressure fuel circuit fault finding.
To interpret the result, apply the interpretation of command SC035 (see Interpretation of commands).
Check the fuel circuit sealing: run Test 3 Low pressure circuit check.
If Test 3 is correct.
If Test 3 is not correct, proceed as follows:
Check the conformity of the type of heater plugs configured:
For Vdiag 20, 24, 38 and 74: consult ET781 Heater plugs in the Ignition/Preheating subfunction and check the
conformity with the type of plugs installed:
– Slow plugs have a black ring.
– Fast plugs have a white ring.
If the heater plugs are being replaced with plugs of a different type (see Replacement of components, Replacing
heater plugs).
For all Vdiags, check that all 4 plugs have the same colour ring.
Check that the heater plugs are actuated using the AC037 Preheating relay command.
Check the sealing and condition of the inlet circuit: run Test 4 Turbocharged air inlet circuit check, and follow
the related fault finding procedure (see Test 4).
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-495V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST2 Resolving misfires
Check for faults DF059 Misfire on cylinder 1, DF060
Misfire on cylinder 2, DF061 Misfire on cylinder 3,
DF062 Misfire on cylinder 4, DF065 Misfire using the
diagnostic tool.
Run a compression test using the M9R flexible end piece,
part number Mot. 1772 and apply command VP036 Fuel
supply inhibition (see Interpretation of commands).
Are the values obtained correct?Check the mechanical conformity of the
valves, heater plugs and segments.
Clear the faults, start the engine and leave the engine
running at idle speed for 1 minute.
Check for faults DF059, DF060, DF061, DF062, DF065
using the diagnostic tool.
Are there any faults remaining?End of test.
Change the faulty injector to another position.
Did the fault follow the injector to its new location?Put the injectors back in their initial
positions.
NO
YES
NO
YES
NO
YES
A
EDC16CP33_V18_TEST2 / EDC16CP33_V1C_TEST2 / EDC16CP33_V54_TEST2 / EDC16CP33_V20_TEST2 / EDC16CP33_V58_TEST2 /
EDC16CP33_V5C_TEST2 / EDC16CP33_V24_TEST2 / EDC16CP33_V04_TEST2 / EDC16CP33_V08_TEST2 / EDC16CP33_V44_TEST2 /
EDC16CP33_V4C_TEST2 / EDC16CP33_V34_TEST2 / EDC16CP33_V38_TEST2 / EDC16CP33_V74_TEST2 / EDC16CP33_V28_TEST2 /
EDC16CP33_V62_TEST2 / EDC16CP33_V26_TEST2 / EDC16CP33_V60_TEST2
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-496V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST2
CONTINUED
Replace the faulty injector by observing the
procedure described in the section
Replacement of components.Clear the faults, start the engine and leave the engine
running at idle speed for 1 minute.
Check for faults DF059, DF060, DF061, DF062, DF065
using the diagnostic tool.
Are there any faults remaining?
End of test.Check the mechanical conformity
of the valves, heater plugs and
segments.
A
YES
NO
YESNO
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-506V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST10
CONTINUED 3
Part C:
Confirmation of flow correction fault finding for each injector (individual correction):
Clear the faults and run a test with the engine at idle speed and the fuel temperature > 50°C, check that no faults
appear on the diagnostic tool and that the correction values do not reach X = ± 5 mg/stroke to confirm the repair.
– If one or more cylinders have flow correction values for an injector which exceed X = ± 5 mg/stroke, follow the
fault finding procedure described in Part A: Fuel regulation balance check for each injector (individual) of
Test 10.
– Otherwise, follow the fault finding procedure described in Part D of Test 10.
Part D:
Injector nozzle sealing check:
Check the level and condition of the engine oil:
– If there is contamination from the diesel fuel, the leaking injector nozzle will be "greasy".
– Disconnect the preheating relay.
– Ensure that this is not caused by rising engine oil by checking the engine compression values.
– Check the condition of the heater plug: this must not be wet. If it is, change the defective injector.
– If the engine compression values are correct: locate the faulty injector by looking at the condition of the cylinders
and the pistons through the heater plug wells (greasy cylinder, overheating, signs of damage, etc.).
– If the cylinder - piston examination is not conclusive, remove the injectors and change the one with the greasy
nozzle.
– If the fault finding checks do not enable the engine to be repaired, contact the Techline.
After replacing the injector, follow the injector code programming procedure (see Replacement of components),
run SC036 Reinitialise programming, and select the number of the injector replaced.
Note:
Before replacing an injector, check for the sealing washer and its conformity (see Fault finding chart ALP4 Poor
performance).
IMPORTANT:
When removing / refitting injectors, follow the cleanliness and safety instructions (see MR 395 (Laguna II ph2),
402 (Vel Satis), 405 (Espace IV Ph2), 364 (Megane II ph2), 370 (Scenic II ph2) Mechanical, 13B, Diesel
injection, Diesel injectors: Removal - Refitting).
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74