13B-453V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
Laguna II ph2, Vel Satis ph2, Espace IV ph2 only.
AC154LOW-SPEED FAN ASSEMBLY
NOTESThere must be no present or stored faults.
Perform this fault finding after an engine cooling fault or air conditioning fault.
Engine stopped.
Use the Wiring Diagram Technical Note for Laguna II ph2, Vel Satis ph2, Espace
IV ph2.
If, when running command AC154, the low speed fan assembly relay does not operate:
Check the condition of the low speed fan assembly relay mounting connectors (see Wiring Diagram Technical
Note, Vehicle, component code 597).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
If the fault is still present, check that the relay is actuated by the engine management computer as follows:
Disconnect the low speed fan assembly relay, fit a 50 Ω to 100 Ω resistor on the relay mounting in place of the
coil, and connect a voltmeter as follows:
– positive terminal to + 12 V battery,
– negative terminal to connection 3JN of component 700.
Run command AC154.
If the voltmeter shows the battery voltage (4 ON-OFF cycles of 10 seconds), replace the relay.
If the voltmeter does not show the battery voltage (4 ON-OFF cycles of 10 seconds), contact the Techline.
If the low speed fan assembly relay is supplied using command AC154, but there is still a fan assembly actuation
fault, use the wiring diagram to check:
The conformity of the fan assembly maxi-fuse.
– Check the continuity of connection 49L between components 700 and 321.
– Check the low speed resistor (resistance and connections).
– Check the continuity of connection 49B between components 262 and 321.
– Check for complete earthing on connection MAS of component 162.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
EDC16CP33_V18_AC154 / EDC16CP33_V1C_AC154 / EDC16CP33_V54_AC154 / EDC16CP33_V20_AC154 / EDC16CP33_V58_AC154 /
EDC16CP33_V5C_AC154 / EDC16CP33_V24_AC154 / EDC16CP33_V04_AC154 / EDC16CP33_V08_AC154 / EDC16CP33_V44_AC154 /
EDC16CP33_V4C_AC154 / EDC16CP33_V34_AC154 / EDC16CP33_V38_AC154 / EDC16CP33_V74_AC154 / EDC16CP33_V28_AC154 /
EDC16CP33_V26_AC154
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
13B-470
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
13B
ALP1 No dialogue with engine management computer
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2,
Scénic II ph2.
STEP 1
Check the conformity of the vehicle type, and the domain selected on the tool.
Check that the tool is not faulty by trying to establish dialogue with a computer on another vehicle.
Check the supply to the diagnostic socket, component code 225, of the following connections:
•BCP4 of component 225 (+ before ignition),
•AP10 of component 225 (+ after ignition),
•NAP and MA of component 225 (earth).
Check the conformity of the after ignition fuse.
– The conformity of the injection relay mounting.
Check the conformity of the main relay (relay removed):
–Insulation between connections 3FB and BP37 of component 983 or 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
– Measure the resistance between connections 3AA and BP37 of component 983 or 1337.
If the resistance of the injection relay is not between: 60 Ω < X < 70 Ω, replace the relay.
Disconnect the engine management computer and check that there are no conducting parts on the computer
studs. If this reveals any kind of impurity, rectify it and try to establish dialogue.
If the fault is still present, place the bornier Elé. 1681 on the engine harness:
Check the continuity and absence of interference resistance on the following multiplex connections:
•133B between components 120 and 225,
•133C between components 120 and 225.
Check the +12 V after relay supply to the engine management computer on the following connections:
•3FB of component 120,
•3FB1 of component 120,
•3FB2 of component 120.
Check for complete earthing on connections NT of component 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
EDC16CP33_V18_ALP01 / EDC16CP33_V1C_ALP01 / EDC16CP33_V54_ALP01 / EDC16CP33_V20_ALP01 / EDC16CP33_V58_ALP01 /
EDC16CP33_V5C_ALP01 / EDC16CP33_V24_ALP01 / EDC16CP33_V04_ALP01 / EDC16CP33_V08_ALP01 / EDC16CP33_V44_ALP01 /
EDC16CP33_V4C_ALP01 / EDC16CP33_V34_ALP01 / EDC16CP33_V38_ALP01 / EDC16CP33_V74_ALP01 / EDC16CP33_V28_ALP01 /
EDC16CP33_V62_ALP01 / EDC16CP33_V26_ALP01 / EDC16CP33_V60_ALP01
DIESEL INJECTION
Fault finding – Fault Finding Chart
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
