2012 RENAULT SCENIC warning

13B-129
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
IMA*: Individual injector correction
IMA*: Individual injector correction
DF066
CONTINUED 1
WARNING:
If fault DF066 is still present after the injector codes have been entered, check that power latch occurs each time
the ignition is switched off:
– Switch off the ignition.
– Wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the computer: EDC16
CP33, check the tool connection and the computer supply voltage and switch on the ignition again.
– Establish dialogue.
If the fault has become stored, clear the fault memory and end the operation.
If the fault is still present, contact the Techline.
2.DEF
NOTESConditions for applying the fault finding procedure to a
stored fault:
The fault is declared present after:
– the injection computer has been replaced,
– reprogramming.
This fault is present on all blank computers (new or after reprogramming).
– Program the injector codes using:
– either command SC001 Write saved data,
– or command SC002 Enter injector codes or Interpretation of commands.
The IMA* codes must be read from left to right.
(Consult the procedures defined in the Interpretation of commands section).

13B-130
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
IMA*: Individual injector correction
DF066
CONTINUED 2
– After the codes have been written:
– Switch off the ignition.
– Wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the computer: EDC16
CP33, check the tool connection and the computer supply voltage and switch on the ignition again.
– Establish dialogue and clear the fault memory.
End of the procedure.
WARNING:
If fault DF066 is still present after the injector codes have been entered, check that power latch occurs each time
the ignition is switched off:
– Switch off the ignition.
– Wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the computer: EDC16
CP33, check the tool connection and the computer supply voltage and switch on the ignition again.
– Establish dialogue.
If the fault is still present, contact the Techline.

13B-131
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF069
PRESENT
OR
STOREDIMPACT DETECTED SIGNAL
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present under + after ignition feed.
Special notes:
As soon as the injection computer receives this signal:
– engine operation is prohibited,
the level 2 warning light is lit.
The fault appears when the injection computer receives a frontal impact signal from the Airbag computer via the
multiplex network.
Do not deal with this fault.
If the vehicle has been involved in an accident:
Carry out any necessary repairs,
– clear the fault,
– switch off the ignition,
–wait for 1 minute,
– switch on the ignition.
If the fault does not reappear, end of fault finding procedure.
If the fault recurs, run fault finding on the AIRBAG computer.
If the vehicle has not been involved in an accident:
Run fault finding on the AIRBAG computer (see 88C, Airbag and pretensioner).
EDC16CP33_V18_DF069 / EDC16CP33_V1C_DF069 / EDC16CP33_V54_DF069 / EDC16CP33_V20_DF069 / EDC16CP33_V58_DF069 /
EDC16CP33_V5C_DF069 / EDC16CP33_V24_DF069 / EDC16CP33_V04_DF069 / EDC16CP33_V08_DF069 / EDC16CP33_V44_DF069 /
EDC16CP33_V4C_DF069 / EDC16CP33_V34_DF069 / EDC16CP33_V38_DF069 / EDC16CP33_V74_DF069 / EDC16CP33_V28_DF069 /
EDC16CP33_V62_DF069 / EDC16CP33_V26_DF069 / EDC16CP33_V60_DF069

13B-139
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF107
PRESENT
OR
STOREDCOMPUTER MEMORY
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault is declared present after:
– a road test followed by a power latch phase.
Special notes:
The level 1 and EOBD (European On Board Diagnostic) warning lights are lit.
If the fault is stored, clear the fault from the computer memory.
In the main screen of the CLIP diagnostic tool, note the injector codes.
Clear the computer memory using command RZ034 Computer memory.
Switch off the ignition, wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the
computer: EDC16 CP33, check the tool connection and the computer supply voltage then switch on the
ignition again.
Switch on the ignition and re-establish dialogue.
If the fault is still present, contact the Techline.
If the fault is no longer present, carry out the programming (see Programming).
Switch off the ignition, wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the
computer: EDC16 CP33, check the tool connection and the computer supply voltage then switch on the
ignition again.
For vehicles equipped with a particle filter:
– Check the exhaust pipe for leaks or blockage. Repair if necessary.
– Carry out a particle filter regeneration using command SC017 Particle filter regeneration (see Interpretation
of commands) and perform an oil change if the vehicle is not new.
EDC16CP33_V18_DF107 / EDC16CP33_V1C_DF107 / EDC16CP33_V54_DF107 / EDC16CP33_V20_DF107 / EDC16CP33_V58_DF107 /
EDC16CP33_V5C_DF107 / EDC16CP33_V24_DF107 / EDC16CP33_V04_DF107 / EDC16CP33_V08_DF107 / EDC16CP33_V44_DF107 /
EDC16CP33_V4C_DF107 / EDC16CP33_V34_DF107 / EDC16CP33_V38_DF107 / EDC16CP33_V74_DF107 / EDC16CP33_V28_DF107 /
EDC16CP33_V62_DF107 / EDC16CP33_V26_DF107 / EDC16CP33_V60_DF107

13B-140
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF119
PRESENT
OR
STOREDCAMSHAFT SENSOR SIGNAL
1.DEF: No camshaft signal or timing fault (tension or setting)
2.DEF: Supply fault, signal interference, camshaft sensor internal fault
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault is declared present after:
– starting the engine,
– a road test.
Special notes:
–the level 1 warning light is lit.
Use bornier Elé.1681 for any operations on the injection computer connectors.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
1.DEF
NOTESNone.
Check the condition of the camshaft sensor connector (see Wiring Diagram Technical Note, Laguna II ph2, Vel
Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 746).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
If the fault is stored:
Visually check the condition of the surrounding area.
If, on detection of the fault, the engine speed is considerably lower than the idling speed (less than 150 rpm) and
no customer complaint is declared (warning light indicated by the customer does not come on and vehicle can be
started), the fault was detected because the engine had stalled.
Clear the fault and carry out a road test.
EDC16CP33_V18_DF119 / EDC16CP33_V1C_DF119 / EDC16CP33_V54_DF119 / EDC16CP33_V20_DF119 / EDC16CP33_V58_DF119 /
EDC16CP33_V5C_DF119 / EDC16CP33_V24_DF119 / EDC16CP33_V04_DF119 / EDC16CP33_V08_DF119 / EDC16CP33_V44_DF119 /
EDC16CP33_V4C_DF119 / EDC16CP33_V34_DF119 / EDC16CP33_V38_DF119 / EDC16CP33_V74_DF119 / EDC16CP33_V28_DF119 /
EDC16CP33_V62_DF119 / EDC16CP33_V26_DF119 / EDC16CP33_V60_DF119

13B-143
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
13B
DF120
PRESENT
OR
STOREDENGINE SPEED SENSOR SIGNAL
1.DEF: Engine speed signal interference, broken tooth on flywheel or engine speed
sensor internal fault
2.DEF: No engine speed signal, or interference affecting engine speed signal
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault is declared present after:
– starting the engine,
– a road test,
– attempting to start the engine.
Special notes:
The engine speed sensor is consistent with the camshaft sensor.
If the fault is present:
– particle filter regeneration is inhibited,
–the level 2 warning light is lit.
Use bornier Elé.1681 for any operations on the injection computer connectors.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Check the condition of the engine speed sensor connector (see Wiring Diagram Technical Note, Laguna II ph2,
Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 149).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check that the sensor is securely attached.
Measure the resistance between connections 3BG and 3BL of component 149.
If the winding resistance is not between 600Ω and 1000Ω, replace the engine speed sensor.
EDC16CP33_V18_DF120 / EDC16CP33_V1C_DF120 / EDC16CP33_V54_DF120 / EDC16CP33_V20_DF120 / EDC16CP33_V58_DF120 /
EDC16CP33_V5C_DF120 / EDC16CP33_V24_DF120 / EDC16CP33_V04_DF120 / EDC16CP33_V08_DF120 / EDC16CP33_V44_DF120 /
EDC16CP33_V4C_DF120 / EDC16CP33_V34_DF120 / EDC16CP33_V38_DF120 / EDC16CP33_V74_DF120 / EDC16CP33_V28_DF120 /
EDC16CP33_V62_DF120/ EDC16CP33_V26_DF120 / EDC16CP33_V60_DF120
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-145
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF151
STOREDMAIN RELAY CIRCUIT1.DEF: Relay cut off too soon
2.DEF: Relay cut off too late
NOTESSpecial notes:
The level 1 warning light is on.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
IMPORTANT:
For Mégane II ph2 and Scénic II ph2, the injection supply relay is located on the UPC.
For Laguna II ph2 and Espace IV ph2, the injection supply relay is located on the
engine fuse and relay box.
1.DEF
NOTESNone.
Check the condition of the injection supply relay mounting connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 983).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the tightness and the condition of the "+ " and "-" battery terminals.
Check the conformity of the main relay (relay removed) (Laguna II ph2 and Espace IV ph2):
•Insulation between connections 3FB and BP37 or 3MV of component 983.
• Measure the resistance between connections3AA and BP37 of component983.
(see Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II
ph2, Component code 983).
Replace the relay if its resistance is less than 6 Ω or greater than 1 kΩ.
EDC16CP33_V18_DF151M / EDC16CP33_V1C_DF151M / EDC16CP33_V54_DF151M / EDC16CP33_V20_DF151M /
EDC16CP33_V58_DF151M / EDC16CP33_V5C_DF151M / EDC16CP33_V24_DF151M / EDC16CP33_V04_DF151M /
EDC16CP33_V08_DF151M / EDC16CP33_V44_DF151M / EDC16CP33_V4C_DF151M / EDC16CP33_V34_DF151M /
EDC16CP33_V38_DF151M / EDC16CP33_V74_DF151M / EDC16CP33_V28_DF151M / EDC16CP33_V62_DF151M/
EDC16CP33_V26_DF151M / EDC16CP33_V60_DF151M
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-148
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF165
PRESENT
OR
STOREDACCELERATOR PEDAL POSITION SENSOR CIRCUIT1.DEF: Detection of the accelerator pedal depressed at the same time as the brake
pedal.
2.DEF: No signal
3.DEF: Jammed accelerator pedal detected
NOTESPriorities when dealing with a number of faults:
– DF012 Sensor supply voltage no. 2.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present when the brake pedal and accelerator pedal are
depressed simultaneously.
Special notes:
– Turbocharging and cruise control are not authorised.
– The engine speed is fixed at 1700 rpm.
–The level 1 warning light is lit for 2.DEF and 3.DEF.
Use bornier Elé.1681 for any operations on the computer connectors.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Check that the accelerator pedal is not jammed
Check the condition of the pedal sensor connector (component code 921).
Check the condition of the engine management computer connector (component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3LT and 3LR of component 921.
If the accelerator pedal sensor resistance is not between: 0.7 kΩ < X < 1.7 kΩ or 0.91 kΩ < X < 2.49 kΩ (M9R721),
replace the sensor.
EDC16CP33_V18_DF165 / EDC16CP33_V1C_DF165 / EDC16CP33_V54_DF165 / EDC16CP33_V20_DF165 / EDC16CP33_V58_DF165 /
EDC16CP33_V5C_DF165 / EDC16CP33_V24_DF165 / EDC16CP33_V04_DF165 / EDC16CP33_V08_DF165 / EDC16CP33_V44_DF165 /
EDC16CP33_V4C_DF165 / EDC16CP33_V34_DF165 / EDC16CP33_V38_DF165 / EDC16CP33_V74_DF165 / EDC16CP33_V28_DF165 /
EDC16CP33_V62_DF165/ EDC16CP33_V26_DF165 / EDC16CP33_V60_DF165
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74