2012 RENAULT SCENIC lock

13B-480
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP5 Irregular engine operation
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic tool.
If the customer complaint is not eliminated, perform the following checks.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
If the engine races during gear changes, if there is a floor mat, check that this is not blocking the accelerator pedal,
the brake pedal and the clutch pedal, then check the conformity of the clutch switch and the conformity of the
accelerator pedal sensor when the pedal is released (see PR086 Pedal potentiometer voltage gang 1 and
PR088 Pedal potentiometer voltage gang 2, Sensor supply).
Measure the resistance between connections 3BG and 3BL of component 149.
If the sensor resistance is not between:
741 Ω < X < 905 Ω at +20°C, replace the sensor.
Check the continuity and absence of interference resistance on the following connections:
•3BG between the components 120 and 149,
•3BL between components 120 and 149.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the conformity of the engine earths (oxidation, tightness, etc.).
Check the mounting and condition (overheating) of the sensor.
Check the low pressure circuit: run Test 3 Low pressure circuit check.
Apply the air flow checking procedure, (see conformity in the interpretation of statuses and parameters).
Check the turbocharger: apply Test 7 Variable geometry turbocharger control.
If the fault is still present, test the high pressure fuel circuit:
Run scenario SC035 High pressure fuel circuit fault finding.
To interpret the result, apply the interpretation of command SC035 (see Interpretation of commands).
EDC16CP33_V18_ALP05 / EDC16CP33_V1C_ALP05 / EDC16CP33_V54_ALP05 / EDC16CP33_V20_ALP05 / EDC16CP33_V58_ALP05 /
EDC16CP33_V5C_ALP05 / EDC16CP33_V24_ALP05 / EDC16CP33_V04_ALP05 / EDC16CP33_V08_ALP05 / EDC16CP33_V44_ALP05 /
EDC16CP33_V4C_ALP05 / EDC16CP33_V34_ALP05 / EDC16CP33_V38_ALP05 / EDC16CP33_V74_ALP05 / EDC16CP33_V28_ALP05 /
EDC16CP33_V62_ALP05 / EDC16CP33_V26_ALP05 / EDC16CP33_V60_ALP05
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-487
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$170.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP9 PARTICLE FILTER WARNING LIGHT COMES ON TOO OFTEN
NOTESBefore dealing with this customer complaint, check that there are no faults except
DF312 Speed request, and the conformity (or otherwise) of the "parameters" and
"statuses" using the diagnostic tool. Deal with the other faults first.
If the customer complaint is not eliminated, perform the following checks.
Have the last 10 regeneration
attempts failed?Are all the regeneration failures
linked to engine cut-off?
See group parameter (ET706
Stored engine status no. 1 to
ET715 Stored engine status no.
10)
(e.g. ET706 STOPPED)Output 1 Is the distance of PR412 Distance of
last successful regeneration less
than all the parameters of group 2?
(PR794 to PR803 Stored
regeneration failure no.1 to no.10)
Is at least one status for group
1 = STATUS4?Check the exhaust pipe for leaks
or blockage. Repair if necessary.
Carry out an After-Sales
regeneration if not already
performed. To do this, see SC017
Particle filter regeneration in
Interpretation of commands.Output 2
YES
YES
NONO
YES
A
NO
B
EDC16CP33_V18_ALP09 / EDC16CP33_V1C_ALP09 / EDC16CP33_V54_ALP09 / EDC16CP33_V20_ALP09 / EDC16CP33_V58_ALP09 /
EDC16CP33_V5C_ALP09 / EDC16CP33_V24_ALP09 / EDC16CP33_V28_ALP09 / EDC16CP33_V62_ALP09 / EDC16CP33_V26_ALP09 /
EDC16CP33_V60_ALP09
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-493V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST1 Exhaust system check
Engine stopped: Check that the silencer outlet is
not blocked. Repair or replace the silencer, if
necessary.
Check the seal of the exhaust manifold on the
contact surface between the turbocharger and the
exhaust manifold.
Is the seal in order?Repair or replace the faulty part.
Loosen the catalytic converter on the turbocharger
side.
Place a wooden block between the two parts.
Start the vehicle and check if the engine runs
better.
Is the engine running normally?The exhaust system is not the cause of the fault;
repeat the engine fault finding (see Customer
complaints - Fault finding chart).
Retighten the catalytic converter.
Loosen or separate the particle filter on the
catalytic converter side. Place a wooden block
between the two parts if necessary.
Start the vehicle and check if the engine runs
better.
Is the engine running normally?Replace the catalytic converter.
NO
YES
NO
YES
NO
YES
A
EDC16CP33_V18_TEST1 / EDC16CP33_V1C_TEST1 / EDC16CP33_V54_TEST1 / EDC16CP33_V20_TEST1 / EDC16CP33_V58_TEST1 /
EDC16CP33_V5C_TEST1 / EDC16CP33_V24_TEST1 / EDC16CP33_V04_TEST1 / EDC16CP33_V08_TEST1 / EDC16CP33_V44_TEST1 /
EDC16CP33_V4C_TEST1 / EDC16CP33_V34_TEST1 / EDC16CP33_V38_TEST1 / EDC16CP33_V74_TEST1 / EDC16CP33_V28_TEST1 /
EDC16CP33_V62_TEST1 / EDC16CP33_V26_TEST1 / EDC16CP33_V60_TEST1
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-497V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST3 Low pressure circuit check
Check the fuel filter:
– Conformity of the fuel filter (correct part number and RENAULT filter).
– Positioning and degree of clogging of the filter cartridge.
– Positioning and condition of the seals.
– If there is metal swarf in the filter:
Replace the fuel filter, bleed the circuit and continue the fault finding procedure.
Supplying the injection system with fuel from an additional tank.
This operation aims to detect possible faults in the low pressure supply system of a vehicle by replacing it entirely
with an additional tank.
Mode:
– Disconnect the diesel fuel supply pipe at the fuel filter inlet and block it with a plug.
– Connect a pipe to the fuel filter inlet and insert the other end in a clean container with a capacity of approximately
5 litres.
– Disconnect the diesel fuel return pipe at the diesel temperature sensor (pump return and injector return join), and
block it using a plug.
– Connect a transparent pipe to the union of the diesel fuel temperature sensor, and insert the other end in the
container.
– Fill the container with clean diesel fuel.
– Start the engine and let the system drain itself of its air (there must not be any air bubbles in the return pipe).
Is the customer complaint still present?If the low pressure circuit is in order, reconnect the
various low pressure circuit pipes, and repeat the
fault finding chart procedure or the procedure for
the fault that referred you to this test.
Are the low pressure circuit connections in order
and in good condition?Carry out the necessary repairs.
YES
NO
NO
A
YES
EDC16CP33_V18_TEST3 / EDC16CP33_V1C_TEST3 / EDC16CP33_V54_TEST3 / EDC16CP33_V20_TEST3 / EDC16CP33_V58_TEST3 /
EDC16CP33_V5C_TEST3 / EDC16CP33_V24_TEST3 / EDC16CP33_V04_TEST3 / EDC16CP33_V08_TEST3 / EDC16CP33_V44_TEST3 /
EDC16CP33_V4C_TEST3 / EDC16CP33_V34_TEST3 / EDC16CP33_V38_TEST3 / EDC16CP33_V74_TEST3 / EDC16CP33_V28_TEST3 /
EDC16CP33_V62_TEST3 / EDC16CP33_V26_TEST3 / EDC16CP33_V60_TEST3
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-498V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST3
CONTINUED
Check the condition and operation of the priming bulb. Perform repairs if necessary and continue the test.
Check the condition of all the low pressure diesel pipes from the tank to the injection pump (in particular no pinching
of pipes).
If the fault is still present with a low fuel level, check the consistency of the actual fuel level and that indicated on
the instrument panel.
The transfer pump is supplied via a Venturi pipe located underneath it.
Check that the opening of the venturi (6 mm to 8 mm in diameter) is not blocked by dirt contained in the fuel tank.
Check the priming of the low pressure diesel circuit.
Check that the fuel tank is correctly filled and that the fuel is correct (see Test 12 Diesel fuel conformity check).
If the diesel fuel is not correct:
– Replace the fuel (diesel fuel).
– Replace the fuel filter (diesel fuel).
– Bleed the low and high pressure fuel circuit (diesel fuel).
Low pressure circuit correct.
A
YES
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-499V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST4 Turbocharged air inlet circuit check
Engine stopped: Check the sealing (leak or air intake) of the low and high pressure air circuit (before/after
turbocharger).
Check the parts that are abnormally greasy of the circuit and reveal a lack of tightness.
Check:
– the condition and fitting of the ducts (foreign, clogged, not joined, kinked, broken, pierced, cut bodies, tightness
of the mounting bolts, etc.).
– the presence, condition and fitting of the seals.
– the present and tightening of the clamps.
– The fitting of the turbocharging pressure sensor.
– The pipes and the take-off point between the air duct and the turbocharging sensor.
Carry out the necessary repairs.
Check the air filter.
Check:
– That the inlet and outlet of the air filter unit is not blocked.
– the condition and the assembly of the air filter unit (disconnected, broken, pierced …).
– The cleanliness, the conformity and the non-distortion of the filter element.
– The air flowmeter: run Test 5 Air flowmeter.
Carry out the necessary repairs
Check:
– the condition of the damper valve,
– the tightening of the mounting bolts,
– cracks in the damper valve.
Carry out the necessary repairs.
A
EDC16CP33_V18_TEST4 / EDC16CP33_V1C_TEST4 / EDC16CP33_V54_TEST4 / EDC16CP33_V20_TEST4 / EDC16CP33_V58_TEST4 /
EDC16CP33_V5C_TEST4 / EDC16CP33_V24_TEST4 / EDC16CP33_V04_TEST4 / EDC16CP33_V08_TEST4 / EDC16CP33_V44_TEST4 /
EDC16CP33_V4C_TEST4 / EDC16CP33_V34_TEST4 / EDC16CP33_V38_TEST4 / EDC16CP33_V74_TEST4 / EDC16CP33_V28_TEST4 /
EDC16CP33_V62_TEST4 / EDC16CP33_V26_TEST4 / EDC16CP33_V60_TEST4
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-500V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
TEST4
CONTINUEDTurbocharged air inlet circuit check
Check that there is no leak at the exhaust manifold, in particular at the exhaust manifold/turbocharger connection.
Check the exhaust, run Test 1 Exhaust pipe check.
Carry out the necessary repairs.
Visually check the EGR circuit sealing.
Note:
The operational clearance of the EGR exchanger flap shaft leaves slight traces of a black substance due to
inconsequential leakage. Do not replace this part.
– Check the condition of the intercooler:
– clogging,
– leaks (vehicle stationary, stabilise the engine speed between 3500 rpm and 4000 rpm and check that there are
no leaks).
Replace if necessary.
Check that the turbocharging pressure sensor take-off point is not blocked.
Carry out the necessary repairs
END OF TEST.
A
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-505V12 MR-372-J84-13B300$180.mif
DIESEL INJECTION
Fault finding – Test13B
Part B (except VDiag 18, 04 and 44):
TEST10
CONTINUED 2
Run SC031 Cylinder operational fault
finding.
Is SC031 correct?
The injectors are operating correctly.Check the engine compressions: use a compression
gauge, M9R hose end piece, part no. Mot. 1772 and apply
command VP036 Fuel supply inhibition (see
Interpretation of commands).
Run compressions on all cylinders.
Are the compressions correct?
Check the cylinder block.Check the fitting of the injector concerned and repair if
necessary.
Otherwise change the injector concerned.
After replacing the injector, follow the injector code
programming procedure (see Replacement of
components), run SC036 Reinitialise programming, and
select the number of the injector replaced.
Repeat Part B of Test 10 to confirm the repairs.
IMPORTANT:
When removing / refitting injectors, follow the cleanliness and safety instructions (see MR 395 (Laguna II ph2),
402 (Vel Satis), 405 (Espace IV Ph2), 364 (Megane II ph2), 370 (Scenic II ph2) Mechanical, 13B, Diesel
injection, Diesel injectors: Removal - Refitting).NO
YES
YESNO
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74