2012 RENAULT SCENIC filter

13B-139
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF107
PRESENT
OR
STOREDCOMPUTER MEMORY
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault is declared present after:
– a road test followed by a power latch phase.
Special notes:
The level 1 and EOBD (European On Board Diagnostic) warning lights are lit.
If the fault is stored, clear the fault from the computer memory.
In the main screen of the CLIP diagnostic tool, note the injector codes.
Clear the computer memory using command RZ034 Computer memory.
Switch off the ignition, wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the
computer: EDC16 CP33, check the tool connection and the computer supply voltage then switch on the
ignition again.
Switch on the ignition and re-establish dialogue.
If the fault is still present, contact the Techline.
If the fault is no longer present, carry out the programming (see Programming).
Switch off the ignition, wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the
computer: EDC16 CP33, check the tool connection and the computer supply voltage then switch on the
ignition again.
For vehicles equipped with a particle filter:
– Check the exhaust pipe for leaks or blockage. Repair if necessary.
– Carry out a particle filter regeneration using command SC017 Particle filter regeneration (see Interpretation
of commands) and perform an oil change if the vehicle is not new.
EDC16CP33_V18_DF107 / EDC16CP33_V1C_DF107 / EDC16CP33_V54_DF107 / EDC16CP33_V20_DF107 / EDC16CP33_V58_DF107 /
EDC16CP33_V5C_DF107 / EDC16CP33_V24_DF107 / EDC16CP33_V04_DF107 / EDC16CP33_V08_DF107 / EDC16CP33_V44_DF107 /
EDC16CP33_V4C_DF107 / EDC16CP33_V34_DF107 / EDC16CP33_V38_DF107 / EDC16CP33_V74_DF107 / EDC16CP33_V28_DF107 /
EDC16CP33_V62_DF107 / EDC16CP33_V26_DF107 / EDC16CP33_V60_DF107

13B-143
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
13B
DF120
PRESENT
OR
STOREDENGINE SPEED SENSOR SIGNAL
1.DEF: Engine speed signal interference, broken tooth on flywheel or engine speed
sensor internal fault
2.DEF: No engine speed signal, or interference affecting engine speed signal
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault is declared present after:
– starting the engine,
– a road test,
– attempting to start the engine.
Special notes:
The engine speed sensor is consistent with the camshaft sensor.
If the fault is present:
– particle filter regeneration is inhibited,
–the level 2 warning light is lit.
Use bornier Elé.1681 for any operations on the injection computer connectors.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Check the condition of the engine speed sensor connector (see Wiring Diagram Technical Note, Laguna II ph2,
Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 149).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check that the sensor is securely attached.
Measure the resistance between connections 3BG and 3BL of component 149.
If the winding resistance is not between 600Ω and 1000Ω, replace the engine speed sensor.
EDC16CP33_V18_DF120 / EDC16CP33_V1C_DF120 / EDC16CP33_V54_DF120 / EDC16CP33_V20_DF120 / EDC16CP33_V58_DF120 /
EDC16CP33_V5C_DF120 / EDC16CP33_V24_DF120 / EDC16CP33_V04_DF120 / EDC16CP33_V08_DF120 / EDC16CP33_V44_DF120 /
EDC16CP33_V4C_DF120 / EDC16CP33_V34_DF120 / EDC16CP33_V38_DF120 / EDC16CP33_V74_DF120 / EDC16CP33_V28_DF120 /
EDC16CP33_V62_DF120/ EDC16CP33_V26_DF120 / EDC16CP33_V60_DF120
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-160
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF209
PRESENT
OR
STOREDEGR VALVE POSITION SENSOR CIRCUITCC.0: Short circuit to earth
CO.0: Open circuit or short circuit to earth
CO.1: Open circuit or short circuit to +12 V
1.DEF: Open circuit or short circuit
NOTESPriorities when dealing with a number of faults:
– DF046 Battery voltage.
– DF012 Sensor supply voltage no. 2.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the ignition is switched on.
– the engine is started,
– a road test.
Special notes:
If the fault is present:
–the EOBD (European On Board Diagnostic) warning light is lit,
– EGR programming cut-off: valve in the closed position,
– particle filter regeneration is inhibited.
Use bornier Elé. 1681 for all operations on the engine management computer
connector.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
CO.1
1.DEF
NOTESNone.
Check the condition of the EGR valve (see Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2,
Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1460 or 169).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33_V18_DF209 / EDC16CP33_V1C_DF209 / EDC16CP33_V54_DF209 / EDC16CP33_V20_DF209 / EDC16CP33_V58_DF209 /
EDC16CP33_V5C_DF209 / EDC16CP33_V24_DF209 / EDC16CP33_V04_DF209 / EDC16CP33_V08_DF209 / EDC16CP33_V44_DF209 /
EDC16CP33_V4C_DF209 / EDC16CP33_V34_DF209 / EDC16CP33_V38_DF209 / EDC16CP33_V74_DF209 / EDC16CP33_V28_DF209 /
EDC16CP33_V62_DF209 / EDC16CP33_V26_DF209 / EDC16CP33_V60_DF209
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-183
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF293
PRESENT
OR
STOREDWATER IN DIESEL FUEL SENSOR
1.DEF: Open circuit on the line or water present in the diesel fuel
NOTESIMPORTANT:
Please observe the cleanliness guidelines and safety advice.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Check that there is no water in the fuel filter.
Bleed the fuel filter and the low pressure diesel circuit if necessary.
Start the engine and wait at least 1 minute to confirm the repair.
If the fault was stored but not present, carry out a road test (see Note).
If the fault is still present:
Check the continuity and absence of interference resistance on the following connection:
•3WT between the components 120 and 414.
Check the + 12 V after relay supply to the water detection sensor on the following connection:
•3FB of component 414.
Check that the earth is in order on connection NT or M of component 414.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Start the engine and wait at least 1 minute to confirm the repair.
If the fault is still present, check the conformity of the fuel used:
– Check that the fuel tank has been filled correctly.
–Run Test 12 Fuel conformity check.
– If the diesel fuel is not correct:
– Replace the diesel fuel.
– Change the diesel filter.
– Bleed the low pressure diesel circuit.
EDC16CP33_V18_DF293 / EDC16CP33_V1C_DF293 / EDC16CP33_V54_DF293 / EDC16CP33_V20_DF293 / EDC16CP33_V58_DF293 /
EDC16CP33_V5C_DF293 / EDC16CP33_V24_DF293 / EDC16CP33_V04_DF293 / EDC16CP33_V08_DF293 / EDC16CP33_V44_DF293 /
EDC16CP33_V4C_DF293 / EDC16CP33_V34_DF293 / EDC16CP33_V38_DF293 / EDC16CP33_V74_DF293 / EDC16CP33_V28_DF293 /
EDC16CP33_V62_DF293 / EDC16CP33_V26_DF293 / EDC16CP33_V60_DF293
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-184
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF293
CONTINUED
If none of these checks reveal any faults:
– Replace the water detection sensor.
– Clear the fault.
Start the engine and wait at least 1 minute to confirm the repair.
Note:
When the water level in the fuel filter unit is below the sensor's electrodes, some driving conditions (cornering,
gradients) may result in water being detected (in fact, the sensor's off-centre position in the fuel filter unit, combined
with the driving conditions, causes water to be detected).
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-185
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF297
PRESENT
OR
STOREDPRESSURE SENSOR
1. DEF: Absent
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
– blue/white smoke and black particles coming from the exhaust,
– the EOBD (European On Board Diagnostic) warning light will come on after three
consecutive driving cycles (starting + 5 seconds + switch off the ignition and wait
40 seconds).
–The level 1 warning light is lit (for Vdiag 20, 24, 58, 5C, 26, 28, 60 and 62).
Priorities when dealing with a number of faults:
– DF315 Particle filter diff. pressure sensor if present or stored.
– DF717 Particle filter upstream pressure if it is present or stored.
NOTE:
In the long term, this fault may lead to premature wear and a greater risk of turbocharger
failure.
Check the condition of the differential pressure sensor connector (see Wiring Diagram Technical Note, Laguna
II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1290).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33_V18_DF297 / EDC16CP33_V1C_DF297 / EDC16CP33_V54_DF297 / EDC16CP33_V20_DF297 / EDC16CP33_V58_DF297 /
EDC16CP33_V5C_DF297 / EDC16CP33_V24_DF297 / EDC16CP33_V28_DF297 / EDC16CP33_V62_DF297 / EDC16CP33_V26_DF297 /
EDC16CP33_V60_DF297
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-186
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF297
CONTINUED
Check the particle filter is present.
If it is present:
Visually check that the particle filter is in good condition by positioning the vehicle on a lift:
– not damaged (no abnormal welds, if necessary compare it with another vehicle fitted with particle filter),
– if there are After-Sales sleeves, as a result of a previous operation, check that the particle filter's contents were
not emptied out when it was removed.
If the particle filter is not working correctly or is absent:
– replace it,
– run command SC036 Reinitialise programming and select After particle filter replacement (see
Interpretation of commands),
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Loss of dialogue
with the computer: EDC16 CP33, check the tool connection and the computer supply voltage,
– then switch on the ignition again,
– clear the faults from the computer memory (this operation must be carried out within 3 minutes of the ignition
being switched on).
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-191
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
diff.*: Differential
temp.*: Temperature
DF308
PRESENT
OR
STOREDCLOGGED PARTICLE FILTER
1.DEF: Maximum limit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
– the EGR function is inhibited,
– the vehicle performance is reduced,
–the level 1 warning light is lit and a warning message (or warning light) is displayed
on the instrument panel,
–the EOBD (European On Board Diagnostic) warning light is lit (except Vdiag 18,
1C, 24 and 54).
Priorities when dealing with a number of faults:
Deal with the following faults first:
– DF315 Particle filter differential pressure sensor if it is present.
– DF308 if DF315 is stored.
– DF717 Particle filter upstream pressure if it is present or stored.
– DF645 Damper valve position regulation if it is present or stored.
– DF272 EGR valve control circuit if it is present or stored.
– DF647 EGR valve position regulation if it is present or stored.
– DF309 Particle filter downstream temperature sensor if it is present or stored.
– DF899 Regeneration temperature threshold exceeded if it is present or stored.
– DF310 Particle filter upstream temperature sensor if it is present or stored.
– DF652 Turbine upstream temperature sensor circuit if it is present or stored.
EDC16CP33_V18_DF308 / EDC16CP33_V1C_DF308 / EDC16CP33_V54_DF308 / EDC16CP33_V20_DF308 / EDC16CP33_V58_DF308 /
EDC16CP33_V5C_DF308 / EDC16CP33_V24_DF308 / EDC16CP33_V28_DF308 / EDC16CP33_V62_DF308 / EDC16CP33_V26_DF308 /
EDC16CP33_V60_DF308
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62