2012 RENAULT SCENIC charging

13B-230
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF651
CONTINUED 1
Check the continuity and insulation from earth of the following connections:
•3MX between components 120 and 1299,
•3MY between components 120 and 1299,
•3MZ between components 120 and 1299.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the wiring of the particle filter downstream temperature sensor, component code 1288, is present (with or without
the sensor being present), check the electrical insulation in relation to + 12 V between the following connections:
–3XU between components 120 and 1288,
–3TG between components 120 and 1288.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the faults DF569 Turbocharging circuit and/or DF1188 Air taken into the turbocharging circuit are present,
perform Test 8 Turbocharger rotating part.
If the fault is still present, replace the turbine upstream pressure sensor.
CC.1
NOTESNone.
Check the condition of the turbine upstream pressure sensor connector (component code 1299).
Check the condition of the engine management computer connector (component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-231
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF651
CONTINUED 2
Check the continuity and insulation from + 12 V of the following connections:
•3MX between components 120 and 1299,
•3MY between components 120 and 1299,
•3MZ between components 120 and 1299.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the faults DF569 Turbocharging circuit and/or DF1188 Air taken into the turbocharging circuit are present,
perform Test 8 Turbocharger rotating part.
If the fault is still present, replace the turbine upstream pressure sensor.
1.DEF
NOTESNone.
Check the condition of the turbine upstream pressure sensor connector (component code 1299).
Check the condition of the engine management computer connector (component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and absence of interference resistance on the following connection:
•3MY between components 120 and 1299.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the faults DF569 Turbocharging circuit and/or DF1188 Air taken into the turbocharging circuit are present,
perform Test 8 Turbocharger rotating part.
Replace the turbine upstream pressure sensor if necessary.
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-259
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF1188
PRESENT
OR
STOREDAIR TAKEN INTO THE TURBOCHARGING CIRCUIT
1.DEF: Air leak in the turbocharging circuit
NOTESPriorities when dealing with a number of faults:
– DF004 Turbocharging pressure sensor circuit.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present with the engine running above 3000 rpm and during the
turbocharger regulation phase (for at least 10 seconds).
Special notes:
If the fault is present:
–the level 1 and OBD warning lights are lit,
– the vehicle performance is reduced,
– engine torque is limited,
– the turbo function is inhibited,
– particle filter regeneration is inhibited,
– the EGR function is inhibited by the engine management computer,
Check the condition of the turbocharging pressure sensor connector (component code 1071).
Check the condition of the turbocharging solenoid valve connector (component code 1475).
Check the condition of the engine management computer connector (component code 120).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation of the following connections:
•3LQ between components 120 and 1071,
•3LP between components 120 and 1071,
•3LN between components 120 and 1071,
•3MG between the components 120 and 1475.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
EDC16CP33_V20_DF1188 / EDC16CP33_V24_DF1188 / EDC16CP33_V04_DF1188 / EDC16CP33_V08_DF1188 /
EDC16CP33_V44_DF1188 / EDC16CP33_V4C_DF1188 / EDC16CP33_V34_DF1188/ EDC16CP33_V38_DF1188 /
EDC16CP33_V74_DF1188 / EDC16CP33_V60_DF1188 / EDC16CP33_V62_DF1188
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 20, 24,
34, 38, 44, 4C, 60, 62, 74

13B-285V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET120PRE-POSTHEATING SIGNAL
STATUS
DEFINITIONPRESENT: This status indicates that the pre-postheating signal is still active.
ABSENT: This status indicates that the pre-postheating signal is not active.
NOTESTest the battery and run fault finding on the charging circuit (see Technical Note
6014A, Checking the charging circuit).
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"PRESENT"Status ET120 is PRESENT when preheating is activated.
Refer to the interpretation of fault DF025 Preheating unit diagnostic line, if status
ET120 remains ABSENT.
"ABSENT"Status ET120 is ABSENT when the pre-postheating is not activated.
Consult the interpretation of faults DF025 Preheating unit diagnostic line and DF017
Preheating unit control circuit if status ET120 is PRESENT instead of ABSENT.
EDC16CP33_V18_ET120 / EDC16CP33_V1C_ET120 / EDC16CP33_V54_ET120 / EDC16CP33_V20_ET120 / EDC16CP33_V58_ET120 /
EDC16CP33_V5C_ET120 / EDC16CP33_V24_ET120 / EDC16CP33_V04_ET120 / EDC16CP33_V08_ET120 / EDC16CP33_V44_ET120 /
EDC16CP33_V4C_ET120 / EDC16CP33_V34_ET120 / EDC16CP33_V38_ET120 / EDC16CP33_V74_ET120 / EDC16CP33_V28_ET120 /
EDC16CP33_V62_ET120 / EDC16CP33_V26_ET120 / EDC16CP33_V60_ET120
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-325V12 MR-372-J84-13B300$110.mif
13B
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
OCR*: Opening Cyclic RatioTool parameter Diagnostic tool title
PR002Alternator charge (Mégane II ph2/Scénic II ph2 only)
PR005EGR valve opening setpoint
PR006Rail pressure regulator current
PR007Rail pressure regulator current setpoint
PR008Rail reference pressure
PR009Turbocharging pressure setpoint
PR015Engine torque
PR017Fuel flow
PR022EGR valve position feedback loop difference
PR023Air flow difference
PR030Accelerator pedal position
PR035Atmospheric pressure
PR037Refrigerant pressure (Mégane II ph2/Scénic II ph2 only)
PR038Rail pressure
PR041Turbocharging pressure
PR042Filtered turbocharging pressure
PR048OCR* rail pressure regulation valve
PR051EGR valve position feedback
PR053Engine speed requested by air conditioning
PR055Engine speed
PR059Inlet air temperature
PR061Exterior air temperature
PR063Fuel temperature
PR064Coolant temperature
PR074Battery voltage
PR077EGR valve position sensor voltage
DIESEL INJECTION
Fault finding – Parameter summary table

13B-326V12 MR-372-J84-13B300$110.mif
DIESEL INJECTION
Fault finding – Parameter summary table13B
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
OCR*: Opening Cyclic Ratio
SV*: Solenoid valveTool parameter Diagnostic tool title
PR079Atmospheric pressure sensor voltage
PR080Rail pressure sensor voltage
PR082Fuel temperature sensor voltage
PR083Air temperature sensor voltage
PR084Coolant temperature sensor voltage
PR086Pedal potentiometer voltage gang 1
PR088Pedal potentiometer gang 2 voltage
PR089Vehicle speed
PR104Turbocharging SV* OCR* setpoint
PR128First EGR valve offset
PR129Last EGR valve offset
PR130Cruise control setpoint
PR132Air flow
PR157Fuel flow setpoint
PR171Air flow setpoint for EGR
PR190Engine idle speed setpoint.
PR209Turbocharging pressure loop difference
PR213Rail pressure loop difference
PR224Turbocharging pressure sensor voltage
PR225Air flow sensor voltage
PR290AC refrigerant pressure sensor voltage (Mégane II ph2/Scénic II ph2 only)
PR364Cylinder no. 1 fuel flow correction
PR365Cylinder no. 4 fuel flow correction
PR381Particle filter downstream temperature
PR382Particle filter upstream temperature
PR383Weight of soot in the particle filter

13B-328V12 MR-372-J84-13B300$110.mif
DIESEL INJECTION
Fault finding – Parameter summary table13B
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
OCR*: Opening Cyclic Ratio,
SV*: Solenoid valve,
solen*: solenoid valve.Tool parameter Diagnostic tool title
PR792DF312 recording No. 9
PR793DF312 recording No. 10
PR794Stored regeneration failure no. 1
PR795Stored regeneration failure no. 2
PR796Stored regeneration failure no. 3
PR797Stored regeneration failure no. 4
PR798Stored regeneration failure no. 5
PR799Stored regeneration failure no. 6
PR800Stored regeneration failure no. 7
PR801Stored regeneration failure no. 8
PR802Stored regeneration failure no. 9
PR803Stored regeneration failure no. 10
PR808Supplier 1-0 signal
PR816Stored regeneration start No.1
PR817Stored regeneration start No. 2
PR818Stored regeneration start No.3
PR819Stored regeneration start No.4
PR820Stored regeneration start No. 5
PR821Stored regeneration start No.6
PR822Stored regeneration start No.7
PR823Stored regeneration start No.8
PR824Stored regeneration start No.9
PR825Stored regeneration start No. 10
PR846Turbocharging SV* OCR*
PR848Regeneration failure number
PR850Fuel flow solen.* current setpoint

13B-335
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR009TURBOCHARGING PRESSURE SETPOINTS
PARAMETER
DEFINITIONThis parameter indicates the theoretical turbocharging pressure setpoint value in bar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or Engine running, and engine coolant
temperature > 80°C
The theoretical turbocharging pressure value is a setpoint of:
PR009 ≈ 1 bar.
EDC16CP33_V18_PR009 / EDC16CP33_V1C_PR009 / EDC16CP33_V54_PR009 / EDC16CP33_V20_PR009 / EDC16CP33_V58_PR009 /
EDC16CP33_V5C_PR009 / EDC16CP33_V24_PR009 / EDC16CP33_V04_PR009 / EDC16CP33_V08_PR009 / EDC16CP33_V44_PR009 /
EDC16CP33_V4C_PR009 / EDC16CP33_V34_PR009 / EDC16CP33_V38_PR009 / EDC16CP33_V74_PR009 / EDC16CP33_V28_PR009 /
EDC16CP33_V62_PR009 / EDC16CP33_V26_PR009 / EDC16CP33_V60_PR009
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74