2012 RENAULT SCENIC air

13B-301V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 3
STATUS 4
Cancel button pressed
The cruise control/speed limiter function is deactivated each time the suspend
button is pressed.
Status ET415 becomes STATUS 4, when driving when:
– Either the cruise control is active, or
– the speed limiter is active
– and when the "0" button is pressed by the driver.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703 Cruise control / speed limiter buttons and run fault
finding on the R/0 control button located on the right-hand side of the steering wheel.
STATUS 5Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the
injection computer receiving a signal that the brake pedal switch has been pressed.
If status ET415 is STATUS 5, consult the interpretation:
- of status ET042 Cruise control / speed limiter,
- of status ET703 Cruise control / speed limiter buttons,
- of status ET704 Brake switch no. 1,
- of status ET705 Brake switch no. 2,
to test the cruise control/speed limiter system components and find the defective
component.
In addition, check the operation of the accelerator pedal, and use the diagnostic tool
to check for any faults associated with the accelerator pedal. Deal with them if
necessary.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-302V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 4
STATUS 5
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 changes to STATUS 5, deal with present faults or those stored in
the injection computer.
If the fault is still present, contact the Techline.
STATUS 6Gear lever in neutral (manual gearbox) or neutral (automatic gearbox)
Status ET415 changes to STATUS 6, when driving, with cruise control active (ET042:
CRUISE CONTROL) and:
– if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
– if the gear lever is put in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on
a manual gearbox without declutching, or into the neutral position on an automatic
transmission, run fault finding on the ABS computer and check the configuration of the
tyre size stored in the computer. If the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-303V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 5
STATUS 7
Lack of correlation between the request and the vehicle speed
Status ET415 becomes STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
This could occur when driving with the cruise control active (ET042 Cruise control /
speed limiter: CRUISE CONTROL) on very steep terrain.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 7 where the surface is not uneven, contact the
Techline.
STATUS 8Automatic gearbox in defect mode.
Status ET415 becomes STATUS 8, when driving with cruise control active
(ET042: CRUISE CONTROL) and if the automatic transmission is in defect mode.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the automatic transmission
computer.
Deal with any present or stored faults (see 23A, Automatic transmission).
Clear the automatic transmission computer memory by running command RZ001.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If STATUS 8 is still present, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-304V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 6
STATUS 9
Vehicle speed monitoring.
Status ET415 becomes STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the ABS computer.
Deal with any present or stored faults (see 38C, Anti-lock braking system,
Interpretation of faults).
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If STATUS 9 is still present, contact the Techline.
STATUS 10Monitoring by injection computer.
Status ET415 becomes STATUS 10 when driving with cruise control active
(ET042 Cruise control / speed limiter: CRUISE CONTROL) and if the injection
computer detects a fault anywhere in the engine management system, or an
engine overspeed or underspeed.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the injection computer.
Deal with any present or stored faults (see Interpretation of faults).
Reinitialise status ET415 on the injection computer by running command RZ001.
If STATUS 10 is still present, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-305V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET587RECIRCULATED EXHAUST GAS COOLING
STATUS
DEFINITIONACTIVE: This status indicates that exhaust gas cooling is recirculated.
INACTIVE: This status indicates that exhaust gas cooling is not recirculated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
INACTIVE:
According to computer programming.
In the event of a fault, consult the interpretation of faults
DF209 EGR valve position sensor circuit and DF647
EGR valve position regulation
.
EDC16CP33_V18_ET587 / EDC16CP33_V1C_ET587 / EDC16CP33_V54_ET587 / EDC16CP33_V20_ET587 / EDC16CP33_V58_ET587 /
EDC16CP33_V5C_ET587 / EDC16CP33_V24_ET587 / EDC16CP33_V04_ET587 / EDC16CP33_V08_ET587 / EDC16CP33_V44_ET587 /
EDC16CP33_V4C_ET587 / EDC16CP33_V34_ET587 / EDC16CP33_V38_ET587 / EDC16CP33_V74_ET587 / EDC16CP33_V28_ET587 /
EDC16CP33_V62_ET587 / EDC16CP33_V26_ET587 / EDC16CP33_V60_ET587
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-306V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET615AUTOMATIC GEARBOX LEVER POSITION
STATUS
DEFINITIONNeutral, 1, 2, 3, 4, 5, 6, reverse.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Note:
This status is specific to engine types M9R 721 and M9R 761.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NEUTRALThis status indicates that the gear lever is in neutral.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
1This status indicates that the gearbox is in 1st gear.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
2This status indicates that the gearbox is in 2nd gear.
If this status is incorrect,
perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
EDC16CP33_V18_ET615 / EDC16CP33_V1C_ET615 / EDC16CP33_V54_ET615 / EDC16CP33_V20_ET615 / EDC16CP33_V58_ET615 /
EDC16CP33_V5C_ET615 / EDC16CP33_V24_ET615 / EDC16CP33_V28_ET615 / EDC16CP33_V62_ET615 / EDC16CP33_V26_ET615 /
EDC16CP33_V60_ET615
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-307V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET615
CONTINUED
3
This status indicates that the gearbox is in 3rd gear.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
4This status indicates that the gearbox is in 4th gear.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
5This status indicates that the gearbox is in 5th gear.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
6This status indicates that the gearbox is in 6th gear.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
REVERSEThis status indicates that the gear lever is in the reverse gear position.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-308V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651EGR PROGRAMMING CUT-OFF
STATUS
DEFINITIONThis status indicates the operating mode of the EGR valve and has 25 different
definitions: STATUS 1 to 24 or NONE.
NOTESNone.
NONENo EGR cut-off, the EGR valve is operating correctly in accordance with
the computer programs.
STATUSES
1, 5, 6, 7, 9, 10, 12,
13, 15, 19, 23, 24Switch off the engine and wait for the diagnostic tool message (maximum time
8 minutes) Communication lost with the computer: EDC16CP33, check the
tool connection and computer supply.
Switch the ignition on and check for faults.
Check the battery voltage with the engine switched off and the engine running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much or attain an engine speed that is too high.
STATUSES
3, 14, 16Accelerate above idle speed for a few seconds.
STATUS 2Check that the clutch pedal status (ET405 Clutch pedal switch) is not ACTIVE,
and that the vehicle has stopped completely.
EDC16CP33_V18_ET651 / EDC16CP33_V1C_ET651 / EDC16CP33_V54_ET651 / EDC16CP33_V20_ET651 / EDC16CP33_V58_ET651 /
EDC16CP33_V5C_ET651 / EDC16CP33_V24_ET651 / EDC16CP33_V04_ET651 / EDC16CP33_V08_ET651 / EDC16CP33_V44_ET651 /
EDC16CP33_V4C_ET651 / EDC16CP33_V34_ET651 / EDC16CP33_V38_ET651 / EDC16CP33_V74_ET651 / EDC16CP33_V28_ET651 /
EDC16CP33_V62_ET651 / EDC16CP33_V26_ET651 / EDC16CP33_V60_ET651
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74