2012 RENAULT SCENIC engine

13B-294V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET285INJECTION -> AUTOMATIC TRANSMISSION CONNECTION
STATUS
DEFINITIONPRESENT
ABSENT
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
PRESENTThere is a multiplex connection between the injection computer and the automatic
transmission computer.
ABSENTThere is no multiplex connection between the injection computer and the automatic
transmission computer, as there is a manual gearbox.
If there is an automatic transmission and the message ABSENT appears:
Run a multiplex network test (see 88B, Multiplex).
Check the continuity and insulation to earth of the following connections:
•3MS and 3MT between components 119 and 120.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
EDC16CP33_V18_ET285 / EDC16CP33_V1C_ET285 / EDC16CP33_V54_ET285 / EDC16CP33_V20_ET285 / EDC16CP33_V58_ET285 /
EDC16CP33_V5C_ET285 / EDC16CP33_V24_ET285 / EDC16CP33_V28_ET285 / EDC16CP33_V62_ET285 / EDC16CP33_V26_ET285 /
EDC16CP33_V60_ET285
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-295V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET341IMMOBILISER CODE PROGRAMMED
STATUS
DEFINITIONYES: This status indicates that the immobiliser code has been programmed.
NO: This status indicates that the immobiliser code has not been programmed.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"YES"Status ET341 is YES if dialogue is possible between the UCH computer and the
injection computer and the key code is recognised
.
The engine is only authorised to start if the code is correctly recognised by the UCH
computer and statusET003 Engine immobiliser is INACTIVE.
In the event of a fault, (see 87B, Passenger compartment connection unit,
Conformity check).
"NO"Status ET341 is NO if dialogue is not possible between the UCH computer and the
injection computer (status ET003 remains ACTIVE).
This fault may be caused by incorrect key programming or a lack of key programming.
In this case, refer to the UCH fault-finding note (see 87B, Passenger compartment
connection unit) and follow the key programming procedure.
If the key programming is not the cause, run a multiplex network test (see 88B,
Multiplexing) and check that dialogue between the UCH and the injection
computer is possible.
If dialogue is not established, contact Techline.
EDC16CP33_V18_ET341 / EDC16CP33_V1C_ET341 / EDC16CP33_V54_ET341 / EDC16CP33_V20_ET341 / EDC16CP33_V58_ET341 /
EDC16CP33_V5C_ET341 / EDC16CP33_V24_ET341 / EDC16CP33_V04_ET341 / EDC16CP33_V08_ET341 / EDC16CP33_V44_ET341 /
EDC16CP33_V4C_ET341 / EDC16CP33_V34_ET341 / EDC16CP33_V38_ET341 / EDC16CP33_V74_ET341 / EDC16CP33_V28_ET341 /
EDC16CP33_V62_ET341 / EDC16CP33_V26_ET341 / EDC16CP33_V60_ET341
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-296V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET405CLUTCH PEDAL SWITCH
STATUS
DEFINITIONACTIVE: this status indicates that the clutch pedal is depressed.
INACTIVE: this status indicates that the clutch pedal is released.
NOTESCan only be displayed for manual gearboxes.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"ACTIVE"Clutch pedal depressed.
Non-conformity of the brake signals and/or the clutch switch signals can cause
the engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
"INACTIVE"Clutch pedal released.
Non-conformity of the brake signals and/or the clutch switch signals can cause
the engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
Sensor electrical conformity
EDC16CP33_V18_ET405 / EDC16CP33_V1C_ET405 / EDC16CP33_V54_ET405 / EDC16CP33_V20_ET405 / EDC16CP33_V58_ET405 /
EDC16CP33_V5C_ET405 / EDC16CP33_V24_ET405 / EDC16CP33_V04_ET405 / EDC16CP33_V08_ET405 / EDC16CP33_V44_ET405 /
EDC16CP33_V4C_ET405 / EDC16CP33_V34_ET405 / EDC16CP33_V38_ET405 / EDC16CP33_V74_ET405 / EDC16CP33_V28_ET405 /
EDC16CP33_V62_ET405 / EDC16CP33_V26_ET405 / EDC16CP33_V60_ET405
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-298V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415CRUISE CONTROL/SPEED LIMITER DEACTIVATION
STATUS
DEFINITIONThis status varies according to engine specifications.
NOTESNone.
Note:
Cruise control can be activated when the vehicle speed exceeds 18 mph (30 km/h).
Status ET415 shows various reasons for deactivation of the cruise control / speed limiter function, due to
a driver request or the external environment (e.g. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ001 "Fault memory" to reset this status to "NONE".
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
STATUS 1:Traction control request.
STATUS 2:Brake pedal depressed.
STATUS 3:Clutch pedal depressed.
STATUS 4:Suspend button pressed.
STATUS 5:Cruise control or speed limiter monitoring.
STATUS 6:Gear lever in neutral (manual gearbox) or neutral position (automatic gearbox).
EDC16CP33_V18_ET415 / EDC16CP33_V1C_ET415 / EDC16CP33_V54_ET415 / EDC16CP33_V20_ET415 / EDC16CP33_V58_ET415 /
EDC16CP33_V5C_ET415 / EDC16CP33_V24_ET415 / EDC16CP33_V04_ET415 / EDC16CP33_V08_ET415 / EDC16CP33_V44_ET415 /
EDC16CP33_V4C_ET415 / EDC16CP33_V34_ET415 / EDC16CP33_V38_ET415 / EDC16CP33_V74_ET415 / EDC16CP33_V28_ET415 /
EDC16CP33_V62_ET415 / EDC16CP33_V26_ET415 / EDC16CP33_V60_ET415
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-300V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 2
STATUS 2
Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2, when driving with the cruise control active
(ET042: CRUISE CONTROL) and brake pedal depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 2 without depressing the brake pedal, consult
the interpretation of statuses ET704 Brake contact no. 1 and ET705 Brake
contact no. 2.
STATUS 3Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to
the engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with the cruise control active
(ET042 Cruise control / speed limiter: CRUISE CONTROL) and the clutch pedal is
depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed, consult
the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with an automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation
to the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, Multiplexing).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-304V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 6
STATUS 9
Vehicle speed monitoring.
Status ET415 becomes STATUS 9 if the vehicle speed received by the computer is
invalid or absent.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the ABS computer.
Deal with any present or stored faults (see 38C, Anti-lock braking system,
Interpretation of faults).
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If STATUS 9 is still present, contact the Techline.
STATUS 10Monitoring by injection computer.
Status ET415 becomes STATUS 10 when driving with cruise control active
(ET042 Cruise control / speed limiter: CRUISE CONTROL) and if the injection
computer detects a fault anywhere in the engine management system, or an
engine overspeed or underspeed.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then Perform fault finding on the injection computer.
Deal with any present or stored faults (see Interpretation of faults).
Reinitialise status ET415 on the injection computer by running command RZ001.
If STATUS 10 is still present, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-305V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET587RECIRCULATED EXHAUST GAS COOLING
STATUS
DEFINITIONACTIVE: This status indicates that exhaust gas cooling is recirculated.
INACTIVE: This status indicates that exhaust gas cooling is not recirculated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
INACTIVE:
According to computer programming.
In the event of a fault, consult the interpretation of faults
DF209 EGR valve position sensor circuit and DF647
EGR valve position regulation
.
EDC16CP33_V18_ET587 / EDC16CP33_V1C_ET587 / EDC16CP33_V54_ET587 / EDC16CP33_V20_ET587 / EDC16CP33_V58_ET587 /
EDC16CP33_V5C_ET587 / EDC16CP33_V24_ET587 / EDC16CP33_V04_ET587 / EDC16CP33_V08_ET587 / EDC16CP33_V44_ET587 /
EDC16CP33_V4C_ET587 / EDC16CP33_V34_ET587 / EDC16CP33_V38_ET587 / EDC16CP33_V74_ET587 / EDC16CP33_V28_ET587 /
EDC16CP33_V62_ET587 / EDC16CP33_V26_ET587 / EDC16CP33_V60_ET587
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-306V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET615AUTOMATIC GEARBOX LEVER POSITION
STATUS
DEFINITIONNeutral, 1, 2, 3, 4, 5, 6, reverse.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Note:
This status is specific to engine types M9R 721 and M9R 761.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NEUTRALThis status indicates that the gear lever is in neutral.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
1This status indicates that the gearbox is in 1st gear.
If this status is incorrect, perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
2This status indicates that the gearbox is in 2nd gear.
If this status is incorrect,
perform a multiplex network test (see 88B, Multiplexing).
Run fault finding on the automatic transmission computer (see MR 372 (Scénic II
ph 2), 407 (Espace IV ph 2), 23A, Automatic transmission).
EDC16CP33_V18_ET615 / EDC16CP33_V1C_ET615 / EDC16CP33_V54_ET615 / EDC16CP33_V20_ET615 / EDC16CP33_V58_ET615 /
EDC16CP33_V5C_ET615 / EDC16CP33_V24_ET615 / EDC16CP33_V28_ET615 / EDC16CP33_V62_ET615 / EDC16CP33_V26_ET615 /
EDC16CP33_V60_ET615
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62