2012 RENAULT SCENIC engine

13B-274V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 1
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
NOT DETECTEDIf the vehicle is not fitted with cruise control/speed limiter function buttons, status
ET042 Cruise control/speed limiter is permanently NOT DETECTED. Confirmation
of the absence of the cruise control or speed limiter function on the vehicle.
If the vehicle is fitted with cruise control or speed limiter function buttons and the main
switch is in the rest (or neutral) position and after the injection computer has been
programmed or reprogrammed, then status ET042 is NOT DETECTED.
To activate the cruise control or speed limiter function, press the main switch in the
cruise control position and then in the speed limiter position.
Return to rest position
The tool displays status ET042: INACTIVE.
If not, several steps must be checked:
1. Return to the multiplex network test page on the Clip application. Repeat the
multiplex network test. Re-establish dialogue with the injection computer.
CheckET042. If ET042 is INACTIVE, the injection computer has detected the
various positions of the main switch. The cruise control/speed limiter is active.
2. If ET042 is still NOT DETECTED, check that the owner of the vehicle has not
had the cruise control/speed limiter function deactivated in the past. Contact
the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-276V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 3
"INACTIVE"
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Check the continuity, insulation and the absence of interference resistance of
the following connections:
•3FX and 3PD between components 1081 and 120 (for Vel Satis ph2, Laguna II
ph2, Espace IV ph2 and Mégane II ph2),
•3FX and 3PD between components 1546 and 120 (for Scénic II ph2).
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Also check:
The engine management computer connections.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-278V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 5
LIMITER
Check the continuity, insulation and the absence of interference resistance of
the following connections:
•3FX and 3PD between components 1081 and 120 (for Vel Satis ph2, Laguna II
ph2, Espace IV ph2 and Mégane II ph2)
•3FX and 3PD between components 1546 and 120 (for Scénic II ph2).
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Also check:
The engine management computer connections.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-280V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042
CONTINUED 7
CRUISE
CONTROL
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Check the continuity, insulation and the absence of interference resistance of
the following connections:
•3FX and 3PD between components 1081 and 120 (for Vel Satis ph2, Laguna II
ph2, Espace IV ph2 and Mégane II ph2),
•3FX and 3PD between components 1546 and 120 (for Scénic II ph2).
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Also check:
The engine management computer connections.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-281V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET076STARTING
STATUS
DEFINITIONPROHIBITED: This status indicates that starting is not possible.
AUTHORISED: This status indicates that starting is possible.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"PROHIBITED"Refer to the fault finding note for the UCH (see 87B, Passenger compartment
connection unit).
"AUTHORISED"Refer to the fault finding note for the UCH (see 87B, Passenger compartment
connection unit).
EDC16CP33_V18_ET076 / EDC16CP33_V1C_ET076 / EDC16CP33_V54_ET076 / EDC16CP33_V20_ET076 / EDC16CP33_V58_ET076 /
EDC16CP33_V5C_ET076 / EDC16CP33_V24_ET076 / EDC16CP33_V04_ET076 / EDC16CP33_V08_ET076 / EDC16CP33_V44_ET076 /
EDC16CP33_V4C_ET076 / EDC16CP33_V34_ET076 / EDC16CP33_V38_ET076 / EDC16CP33_V74_ET076 / EDC16CP33_V28_ET076 /
EDC16CP33_V62_ET076 / EDC16CP33_V26_ET076 / EDC16CP33_V60_ET076
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-282V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET077IMPACT DETECTED
STATUS
DEFINITIONNO: This status indicates that the airbag computer has not detected an impact.
YES: This status indicates that the airbag computer has detected an impact.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
This signal is transmitted by the airbag computer via the multiplex network.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"NO"The status is usually NO as no impact has been detected.
Otherwise, check the airbag computer (see88C, Airbags and pretensioners).
"YES"If YES an impact must be present.
Otherwise, check the airbag computer (see88C, Airbags and pretensioners).
After the repair, clear the faults (even if no fault is displayed).
EDC16CP33_V18_ET077 / EDC16CP33_V1C_ET077 / EDC16CP33_V54_ET077 / EDC16CP33_V20_ET077 / EDC16CP33_V58_ET077 /
EDC16CP33_V5C_ET077 / EDC16CP33_V24_ET077 / EDC16CP33_V04_ET077 / EDC16CP33_V08_ET077 / EDC16CP33_V44_ET077 /
EDC16CP33_V4C_ET077 / EDC16CP33_V34_ET077 / EDC16CP33_V38_ET077 / EDC16CP33_V74_ET077 / EDC16CP33_V28_ET077 /
EDC16CP33_V62_ET077 / EDC16CP33_V26_ET077 / EDC16CP33_V60_ET077
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-283V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET079AIR CONDITIONING PRESENT
STATUS
DEFINITIONYES: This status indicates that air conditioning is present on the vehicle.
NO: This status indicates that air conditioning is not present on the vehicle.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
The heating and air conditioning system is present depending on the vehicle's
equipment level.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
YES or NOYES or NO, depending on the vehicle equipment.
EDC16CP33_V18_ET079 / EDC16CP33_V1C_ET079 / EDC16CP33_V54_ET079 / EDC16CP33_V20_ET079 / EDC16CP33_V58_ET079 /
EDC16CP33_V5C_ET079 / EDC16CP33_V24_ET079 / EDC16CP33_V04_ET079 / EDC16CP33_V08_ET079 / EDC16CP33_V44_ET079 /
EDC16CP33_V4C_ET079 / EDC16CP33_V34_ET079 / EDC16CP33_V38_ET079 / EDC16CP33_V74_ET079 / EDC16CP33_V28_ET079 /
EDC16CP33_V62_ET079 / EDC16CP33_V26_ET079 / EDC16CP33_V60_ET079
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-284V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
IMA*: Individual injector correction
ET104INJECTOR CODE USE
STATUS
DEFINITIONNO: This status indicates that the injector codes have not been entered.
YES: This status indicates that the injector codes have been entered.
FAULTY: This status indicates that there has been an injector code entry fault.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"NO"If status ET104 is NO, program the injector codes using:
either command SC002 Enter injector codes (the IMA* codes must be read from
left to right),
or command SC001 Write saved data when replacing with a blank computer
orafter reprogramming (see Interpretation of commands).
"YES"When injector code programming is complete, status ET104 becomes YES.
"FAULTY"If status ET104 is FAULTY, program the injector codes using:
– either command SC002 (the IMA* codes must be read from left to right),
– or command SC001 when replacing with a blank computer or after
reprogramming (see Interpretation of commands).
EDC16CP33_V18_ET104 / EDC16CP33_V1C_ET104 / EDC16CP33_V54_ET104 / EDC16CP33_V20_ET104 / EDC16CP33_V58_ET104 /
EDC16CP33_V5C_ET104 / EDC16CP33_V24_ET104 / EDC16CP33_V04_ET104 / EDC16CP33_V08_ET104 / EDC16CP33_V44_ET104 /
EDC16CP33_V4C_ET104 / EDC16CP33_V34_ET104 / EDC16CP33_V38_ET104 / EDC16CP33_V74_ET104 / EDC16CP33_V28_ET104 /
EDC16CP33_V62_ET104 / EDC16CP33_V26_ET104 / EDC16CP33_V60_ET104
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74