2012 RENAULT PULSE ESP


> (GLW    0RGHO .$2(0B5HQDXOW @
ignition switch position will change to “ACC”.
NOTE:
.When the ignition switch is pushed to the
“ACC” or“ON” position or the engine is
started by the above procedures, the Intel-
ligent Key battery discharge indicator ap-
pears (on the Vehicle information display) or
the Intelligent Key system warning light may
blink in yellow (on the meter) even if the
Intelligent Key is inside the vehicle. This is
not a malfunction. To stop the warning light
from blinking, touch the ignition switch with
the Intelligent Key again.
. If the Intelligent Key battery discharge
indicator appears (on the Vehicle informa-
tion display) or the Intelligent Key system
warning light in the meter is blinking in
green, replace the battery as soon as
possible. (See “Battery”(P.8-23) .)GA\fOLI\bE E\bGI\bE
1. Apply the parking brake.
2. Depress the foot brake pedal.
3.Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the selector lever to the “P” (Park) or “\b”
(\beutral) position.
The starter is designed to operate only when
the selector lever is in the proper position.
Manual Transmission (MT) model:
Move the shift lever to the “\b” (\beutral) position,
and depress the clutch pedal to the floor while
starting the engine.
The starter is designed to not operate unless
the clutch pedal is depressed.
4. Crank the engine with your foot off the accelerator pedal by turning the ignition switch to the “\fTART”
position.
5. Immediately release the ignition switch when the engine starts. If the engine starts, but fails to run,
repeat the above procedures.
If the engine is very hard to start in extremely cold
or hot weather, depress the accelerator pedal and
hold it to help start the engine.
CAUTION:
.Do not operate the starter for more than 15
seconds at a time. If the engine does not
start, turn the ignition switch off and wait 10
seconds before cranking the engine again.
Otherwise, the starter could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables, the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
6. Allow the engine to idle for at least 30 seconds after starting the engine to warm-up. Drive at
moderate speeds for a short distance first,
especially in cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
DIE\fEL E\bGI\bE
1. Apply the parking brake.
2. Depress the foot brake pedal.
3. Move the shift lever to the “\b” (\beutral) position,and depress the clutch pedal to the floor while
starting the engine.
4. Turn the ignition switch to the “O\b” position and wait until the glow plug indicator light
turns
off.
5. Crank the engine with your foot off the accelerator pedal by turning the ignition switch to the “\fTART”
position.
6. Immediately release the ignition switch when the engine starts. If the engine starts, but fails to run,
repeat the above procedures.
CAUTION:
.Do not operate the starter for more than 20
seconds at a time. If the engine does not
start, turn the ignition switch off and wait 20
seconds before cranking the engine again.
Otherwise, the starter could be damaged.
Starting and driving5-9
STARTING ENGINE (model without
Intelligent Key system)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-10Starting and driving
.If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
7. Allow the engine to idle for \ft le\fst 30 seconds \ffter st\frting the engine to w\fr\b-up. Drive \ft
\boder\fte speeds for \f short dist\fnce first,
especi\flly in cold we\fther.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
GASOLINE ENGINE
1. Apply the p\frking br\fke.
2.Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the selector lever to the “P” (P\frk) or the “N”
(Neutr\fl) position.
The starter is designed to operate only when
the selector lever is in the proper position.
Manual Transmission (MT) model:
Move the shift lever to the “N” (Neutr\fl) position.
The starter is designed to not operate unless
the clutch pedal is fully depressed.
The Intelligent Key must be carried when
operating the ignition switch.
3. Push the ignition switch to the “ON” position. Depress the br\fke ped\fl (AT/CVT \bodel) or the
clutch ped\fl (MT \bodel) \fnd push the ignition
switch to st\frt the engine.
To st\frt the engine i\b\bedi\ftely, push \fnd rele\fse
the ignition switch while depressing the br\fke
ped\fl or clutch ped\fl with the ignition switch in
\fny position.
4. I\b\bedi\ftely rele\fse the ignition switch when the engine st\frts. If the engine st\frts, but f\fils to run,
repe\ft the \fbove procedures.
If the engine is very h\frd to st\frt in extre\bely cold
or hot we\fther, depress the \fcceler\ftor ped\fl \fnd
hold it. Push the ignition switch for up to 15
seconds while holding. Rele\fse the \fcceler\ftor
ped\fl when the engine st\frts.CAUTION:
.As soon as the engine has started, release
the ignition switch immediately.
. Do not operate the starter for more than 15
seconds at a time. If the engine does not
start, push the ignition switch to the “OFF”
position and wait 10 seconds before crank-
ing the engine again. Otherwise, the starter
could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
5. Allow the engine to idle for \ft le\fst 30 seconds \ffter st\frting the engine to w\fr\b-up. Drive \ft
\boder\fte speeds for \f short dist\fnce first,
especi\flly in cold we\fther.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
6. To stop the engine, \bove the selector lever to the“P” (P\frk) position (AT/CVT \bodel) or \bove the
shift lever to the “N” (Neutr\fl) position (MT \bodel) ,
\fpply the p\frking br\fke \fnd push the ignition
switch to the “OFF” position.
STARTING ENGINE (model with
Intelligent Key system)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
DIESEL ENGINE
1. Apply the park\fng brake.
\b. Move the sh\fft lever to the “N” (Neutral) pos\ft\fon.The starter is designed to not operate unless
the clutch pedal is fully depressed.
The Intelligent Key must be carried when
operating the ignition switch.
3. Push the \fgn\ft\fon sw\ftch to the “ON” pos\ft\fon and wa\ft unt\fl the glow plug \fnd\fcator l\fght turns off.
Depress the clutch pedal and push the \fgn\ft\fon
sw\ftch to start the eng\fne.
To start the eng\fne \fmmed\fately, push and release
the \fgn\ft\fon sw\ftch wh\fle depress\fng the clutch
pedal w\fth the \fgn\ft\fon sw\ftch \fn any pos\ft\fon.
4. Immed\fately release the \fgn\ft\fon sw\ftch when the eng\fne starts. If the eng\fne starts, but fa\fls to run,
repeat the above procedures.
If the eng\fne \fs very hard to start \fn extremely cold
or hot weather, depress the accelerator pedal and
hold \ft. Push the \fgn\ft\fon sw\ftch for up to 15
seconds wh\fle hold\fng. Release the accelerator
pedal when the eng\fne starts.
CAUTION:
.As soon as the engine has started, release
the ignition switch immediately.
. Do not operate the starter for more than 20
seconds at a time. If the engine does not
start, push the ignition switch to the “OFF”
position and wait 20 seconds before crank-
ing the engine again. Otherwise, the starter
could be damaged. .
If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
5. Allow the eng\fne to \fdle for at least 30 seconds after start\fng the eng\fne to warm-up. Dr\fve at
moderate speeds for a short d\fstance f\frst,
espec\fally \fn cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
6. To stop the eng\fne, move the sh\fft lever to the “N”(Neutral) pos\ft\fon, apply the park\fng brake and
push the \fgn\ft\fon sw\ftch to the “OFF” pos\ft\fon.
DRIVING WITH AUTOMATIC TRANSMIS-
SION (AT)
The Automat\fc Transm\fss\fon (AT) \fn your veh\fcle \fs
electron\fcally controlled to produce max\fmum power
and smooth operat\fon.
The recommended operat\fng procedures for th\fs
transm\fss\fon are shown on the follow\fng pages. Follow
these procedures for max\fmum veh\fcle performance
and dr\fv\fng enjoyment.
CAUTION:
.The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up.
. Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Do not downshift abruptly on slippery roads.
This may cause a loss of control.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
your vehicle checked by a RENAULT dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idling speed while
shifting from the “N” (Neutral) position to
any driving position.
Starting and driving5-11
DRIVING VEHICLE
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5. Place the ignition switch in the “ON” \fosition tounlock the steering wheel.
\bhe vehicle may be moved to the desired location.
Re\flace the removed shift lock release cover after the
o\feration.
For model with Intelligent Key system: If the battery is
discharged com\fletely, the steering wheel cannot be
unlocked. Do not move the vehicle with the steering
wheel locked.
If the selector lever cannot be moved out of the “P”
(Park) \fosition, have a RENAUL\b dealer check the
CV\b system as soon as \fossible.
WARNING:
If the selector lever cannot be moved from the
“P” (Park) position while the engine is running
and the brake pedal is depressed, the stop lights
may not work. Malfunctioning stop lights could
cause an accident injuring yourself and others.
High fluid tem\ferature \frotection mode
\bhis transmission has a high fluid tem\ferature \frotec-
tion mode. If the fluid tem\ferature becomes too high
(for exam\fle, when climbing stee\f grades in high
tem\ferature with heavy loads, such as when towing a
trailer) , engine \fower and, under some conditions,
vehicle s\feed will be decreased automatically to
reduce the chance of transmission damage. Vehicle
s\feed can be controlled with the accelerator \fedal,
but engine and vehicle s\feed may be limited.
Fail-safe
When the fail-safe o\feration occurs, the CV\b will not
be shifted to the selected driving \fosition.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
place the ignition switch in the “OFF”position
and wait for 10 seconds. Then turn the ignition
switch back to the “ON”position. The vehicle
should return to its normal operating condition.
If it does not return to its normal operating
condition, have a RENAULT dealer check the
transmission and repair it if necessary.
WARNING:
When the fail-safe operation occurs, vehicle
speed may be gradually reduced. The reduced
speed may be lower than other traffic, which
could increase the chance of a collision. Be
especially careful when driving. If necessary, pull
to the side of the road at a safe place and allow
the transmission to return to normal operation,
or have it repaired if necessary.
DRIVING WI\bH MANUAL \bRANSMISSION
(M\b)
WARNING:
. Do not downshift abruptly on slippery roads.
This may cause a loss of vehicle control.
. Do not over-rev the engine when shifting to
a lower gear. This may cause a loss of
vehicle control or engine damage.
CAUTION:
.Do not rest your foot on the clutch pedal
while driving. This may damage the clutch
system.
. Fully depress the clutch pedal before shift-
ing to help prevent transmission damage.
. Stop the vehicle completely before shifting
into the “R” (Reverse) position.
. When the vehicle is stopped for a period of
time, for example waiting at stoplights, shift
to the “N” (Neutral) position and release the
clutch pedal with the foot brake pedal
depressed.
. Do not shift to the "N" (Neutral) position
while driving. Doing so may result in an
accident due to loss of engine braking.
Starting and driving5-17
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-24Starting and driving
WARNING:
.The VDC system is designed to help improve
driving stability but does not prevent acci-
dents due to abrupt steering operation at
high speeds or due to careless or dangerous
driving techniques. Reduce vehicle speed
and be especially careful when driving and
cornering on slippery surfaces and always
drive carefully.
. Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars, bushings and
wheels are not RENAULT-approved or are
extremely deteriorated, the VDC system may
not operate properly. This could adversely
affect vehicle handling performance, and the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If brake related parts such as brake pads,
rotors and calipers are not standard equip-
ment or are extremely deteriorated, the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If engine related parts such as a muffler are
not standard equipment or are extremely
deteriorated, the “VDC OFF” indicator or
“ SLIP ”indicator or both indicator lights
may illuminate.
. When driving on extremely inclined surfaces
such as higher banked corners, the VDC
system may not operate properly and the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate. Do not
drive on these types of roads. .
When driving on unstable surfaces such as a
turntable, ferry, elevator or ramp, the “VDC
OFF” indicator or “SLIP”indicator or both
indicator lights may illuminate. This is not a
malfunction. Restart the engine after driving
onto a stable surface.
. If wheels or tires other than those recom-
mended are used, the VDC system may not
operate properly and “VDC OFF”indicator or
“SLIP” indicator or both indicator lights may
illuminate.
. The VDC system is not a substitute for winter
tires or tire chains on a snowcovered road.
When accelerating or \friving on slipper\b surfaces, the
tires ma\b spin or sli\fe. With the Vehicle D\bnamic
Control (VDC) s\bstem, sensors \fetect these move-
ments an\f control the braking an\f engine output to
help improve vehicle stabilit\b.
. When the VDC s\bstem is operating, the “SLIP”
in\ficator in the instrument panel blinks.
. If the “SLIP” in\ficator blinks, the roa\f con\fitions
are slipper\b. Be sure to a\fjust \bour spee\f an\f
\friving to these con\fitions. Be sure to \frive
carefull\b. (See “Slip in\ficator light” (P.2-17)
an\f“Vehicle D\bnamic Control (VDC) off in\ficator
light” (P.2-18) .)
. In\ficator light
If a malfunction occurs in the s\bstem, the “SLIP”
an\f “VDC OFF” in\ficator lights illuminate in the
instrument panel. As long as these in\ficators are
illuminate\f, the VDC s\bstem function is cancele\f.
The VDC s\bstem uses a Brake Limite\f Slip Differential
(BLSD) function to improve vehicle traction. The BLSD
s\bstem works when one of the \friving wheels is
spinning on a slipper\b surface. The BLSD s\bstem
brakes the spinning wheel, which \fistributes the \friving power to the other \frive wheel. If the vehicle
is operate\f with the VDC OFF switch pushe\f an\f the
VDC s\bstem turne\f off, all VDC s\bstems will be turne\f
off. The BLSD s\bstem will still operate with the VDC
s\bstem off. If the BLSD s\bstem is activate\f, the “SLIP”
in\ficator light will blink an\f \bou ma\b hear a clunk noise
an\f/or feel a pulsation in the foot brake pe\fal. This is
normal an\f is not an in\fication of a malfunction. While
the VDC s\bstem is operating, \bou ma\b feel a pulsation
in the foot brake pe\fal an\f hear a noise or feel a
vibration from un\fer the hoo\f. This is normal an\f
in\ficates that the VDC s\bstem is working properl\b.
The VDC s\bstem computer has a built-in \fiagnostic
feature that tests the s\bstem each time \bou start the
engine an\f move the vehicle at a low spee\f forwar\f or
backwar\f. When the self-test occurs, \bou ma\b hear a
“clunk” noise an\f/or feel a pulsation in the foot brake
pe\fal. This is normal an\f is not an in\fication of a
malfunction.
VEHICLE DYNAMIC CONTROL (VDC) OFF
SWITCH
SIC1881
The vehicle shoul\f be \friven with the Vehicle D\bnamic
Control (VDC) s\bstem ON for most \friving con\fitions.
When the vehicle is stuck in mu\f or snow, the VDC
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM (if equipped except for
Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
system reduces the engine output to reduce wheel
spin. The engine speed will \fe reduced even if the
accelerator is depressed to the floor. \bf maximum
engine power is needed to free a stuck vehicle, turn
the VDC system off.
To turn off the Vehicle Dynamic Control (VDC) system,
push the VDC OFF switch. The
indicator light will
illuminate on.
Push the VDC OFF switch again or restart the engine
to turn ON the system.
WARNING:
. The Electronic Stability Program (ESP) sys-
tem is designed to help improve driving
stability but does not prevent accidents due
to abrupt steering operation at high speeds
or due to careless or dangerous driving
techniques. Reduce vehicle speed and be
especially careful when driving and corner-
ing on slippery surfaces and always drive
carefully.
. If engine related parts such as a muffler are
not standard equipment or the “ESP OFF”
indicator or “SLIP”indicator or both indica-
tor lights may illuminate.
. Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars and bushings
are not RENAULT approved or are extremely
deteriorated the ESP system may not oper-
ate properly. This could adversely affect
vehicle handling performance, and the
“ESP OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If brake related parts such as brake pads,
rotors and calipers are not standard equip-
ment or are extremely deteriorated, the “ESP
OFF” indicator or “SLIP”indicator or both
indicator lights may illuminate.
. When driving on extremely inclined surfaces
such as higher banked corners, the ESP
system may not operate properly and the
“ESP OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate. Do not
drive on these types of roads. .
When driving on unstable surfaces such as a
turntable, ferry, elevator or ramp, the “ESP
OFF” indicator or “SLIP”indicator or both
indicator lights may illuminate. This is not a
malfunction. Restart the engine after driving
onto a stable surface.
. If wheels or tires other than those recom-
mended are used, the ESP system may not
operate properly and “SLIP”indicator light
may illuminate.
. The ESP system is not a substitute for winter
tires or tire chains on a snow-covered road.
. When the ESP system is operating, the “SL\bP”
indicator
in the instrument panel \flinks.
. \bf the “SL\bP” indicator \flinks, the road conditions
are slippery. Be sure to adjust your speed and
driving to these conditions. Be sure to drive
carefully. (See “Slip indicator light” (P.2-17) and
“Electronic Sta\fility Program (ESP) off indicator
light” (P.2-16) .)
. \bndicator light
\bf a malfunction occurs in the system, the “SL\bP”
indicator lights illuminate in the instrument
panel. As long as these indicators are illuminated,
the ESP system function is canceled.
The ESP system uses a Brake Limited Slip Differential
(BLSD) function to improve vehicle traction. The BLSD
system works when one of the driving wheels is
spinning on a slippery surface. The BLSD system
\frakes the spinning wheel, which distri\futes the
driving power to the other drive wheel. \bf the vehicle
is operated with the ESP system turned off, all ESP
system functions will \fe turned off.
The BLSD system and ABS will still operate with the
ESP system off. \bf the BLSD system is activated, the
“SL\bP” indicator light will \flink and you may hear a
Starting and driving5-25
ELECTRONIC STABILITY PROGRAM
(ESP) SYSTEM (if equipped for
Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-26Starting and driving
clunk noise and/or feel a pulsa\fion in \fhe brake pedal.
\bhis is normal and is no\f an indica\fion of a malfunc\fion.
While \fhe ESP sys\fem is opera\fing, you may feel a
pulsa\fion in \fhe brake pedal and hear a noise or feel a
vibra\fion from under \fhe hood. \bhis is normal and
indica\fes \fha\f \fhe ESP sys\fem is working properly.
\bhe ESP sys\fem compu\fer has a buil\f-in diagnos\fic
fea\fure \fha\f \fes\fs \fhe sys\fem each \fime you s\far\f \fhe
engine and move \fhe vehicle a\f a low speed forward or
backward. When \fhe self-\fes\f occurs, you may hear a
“clunk” noise and/or feel a pulsa\fion in \fhe foo\f brake
pedal. \bhis is normal and is no\f an indica\fion of a
malfunc\fion.
ELEC\bRONIC S\bABILI\bY PROGRAM (ESP)
OFF SWI\bCH
JVS0022X
\bhe vehicle should be driven wi\fh \fhe Elec\fronic
S\fabili\fy Program (ESP) sys\fem on for mos\f driving
condi\fions.
When \fhe vehicle is s\fuck in mud or snow, \fhe ESP
sys\fem reduces \fhe engine ou\fpu\f \fo reduce wheel
spin. \bhe engine speed will be reduced even if \fhe
accelera\for is depressed \fo \fhe floor. If maximum
engine power is needed \fo free a s\fuck vehicle, \furn
\fhe ESP sys\fem off.\bo \furn off \fhe ESP sys\fem, push \fhe ESP OFF swi\fch
loca\fed on \fhe lower side of \fhe ins\frumen\f panel.
\bhe
indica\for ligh\f will illumina\fe.
Push \fhe ESP OFF swi\fch again or res\far\f \fhe engine
\fo \furn on \fhe sys\fem. \bhe speed limi\fer allows you \fo se\f \fhe desired vehicle
speed limi\f. While \fhe speed limi\fer is ac\fiva\fed, \fhe
driver can perform normal braking and accelera\fion,
bu\f \fhe vehicle will no\f exceed \fhe se\f speed.
WARNING:
.
Always observe posted speed limits. Do not
set the speed over them.
. Always confirm the setting status of the
speed limiter on the vehicle information
display and instrument panel.
When \fhe speed limi\fer is on, \fhe cruise con\frol canno\f
be opera\fed.
SPEED LIMI\bER OPERA\bIONS
Excep\f for HR12DDR engine model: \bhe speed limi\fer
can be se\f be\fween 30 km/h and 170 km/h or 20 MPH
and 105 MPH.
For HR12DDR engine model (for M\b model): \bhe
speed limi\fer can be se\f be\fween 30 km/h and 180
km/h or 20 MPH and 112 MPH.
For HR12DDR engine model (for CV\b model): \bhe
speed limi\fer can be se\f be\fween 30 km/h and 170
km/h or 20 MPH and 105 MPH.
\bhe speed limi\fer se\f swi\fches are loca\fed on \fhe
s\feering wheel.
SPEED LIMITER (if equipped for
Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-34Starting and driving
JVS0031X
Measurement result:
The displa\f indicatin\b the measurement result
*B(“OK”, “DIFFICULT” or “NOT ADVISED” ) will appear in
the meter as illustrated.
CAUTION:
.This system provides you with an estimation
of the space in which parallel parking is
possible. Be aware that the system does not
guarantee that parking is always possible in
this space.
. This system may not be able to measure the
parking space correctly between the tall
vehicles such as trucks.
. When the tire pressure is not correct, this
system may not be able to measure the
parking space correctly.
. When replacing a tire with one other than a
genuine RENAULT tire (the same size as the
original tire) , have your vehicle adjusted by
RENAULT dealer. If genuine RENAULT tires
are not used, the system cannot guarantee
accurate measurement of the parking space. .
When the sensor is covered in snow or mud,
the system may not be able to measure the
parking space correctly. Always keep your
sensor clean.
JVS0029X
*1Parkin\b space measurement switch
*2ON indicator li\bht
Setting the level mode:
Dependin\b on \four drivin\b level, the modes can be
selected from the followin\b.
. Amateur .
Normal
. Expert
To set the mode, perform the followin\b procedure:
1. Push and hold the parkin\b space measurement switch
*1for at least 5 seconds. The buzzer then
sounds for 5 seconds.
2. Push the switch
*1the number of times needed
to set the desired mode within 10 seconds. After
10 seconds, the buzzer sounds the number of
times previousl\f pushed.
If the switch is not pushed, the buzzer will sound the
number of times that corresponds to the current mode
set.
The mode can be selected to "Amateur", "Normal" and
"Expert" b\f pushin\b the switch once to three times
while the buzzer sounds as follows:
. Push the switch once to select Amateur mode.
. Push the switch two times to select Normal mode.
. Push the switch three times to select Expert mode.
Each mode indicates the size of space in which
parkin\b is possible as follows:
. The Amateur mode indicates the lar\best parkin\b
space.
. The Normal mode indicates the medium parkin\b
space.
. The Expert mode indicates the smallest parkin\b
space.
&RQGLWLRQ