2012 RENAULT PULSE automatic transmission


> (GLW    0RGHO .$2(0B5HQDXOW @
5-10Starting and driving
.If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
7. Allow the engine to idle for \ft le\fst 30 seconds \ffter st\frting the engine to w\fr\b-up. Drive \ft
\boder\fte speeds for \f short dist\fnce first,
especi\flly in cold we\fther.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
GASOLINE ENGINE
1. Apply the p\frking br\fke.
2.Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the selector lever to the “P” (P\frk) or the “N”
(Neutr\fl) position.
The starter is designed to operate only when
the selector lever is in the proper position.
Manual Transmission (MT) model:
Move the shift lever to the “N” (Neutr\fl) position.
The starter is designed to not operate unless
the clutch pedal is fully depressed.
The Intelligent Key must be carried when
operating the ignition switch.
3. Push the ignition switch to the “ON” position. Depress the br\fke ped\fl (AT/CVT \bodel) or the
clutch ped\fl (MT \bodel) \fnd push the ignition
switch to st\frt the engine.
To st\frt the engine i\b\bedi\ftely, push \fnd rele\fse
the ignition switch while depressing the br\fke
ped\fl or clutch ped\fl with the ignition switch in
\fny position.
4. I\b\bedi\ftely rele\fse the ignition switch when the engine st\frts. If the engine st\frts, but f\fils to run,
repe\ft the \fbove procedures.
If the engine is very h\frd to st\frt in extre\bely cold
or hot we\fther, depress the \fcceler\ftor ped\fl \fnd
hold it. Push the ignition switch for up to 15
seconds while holding. Rele\fse the \fcceler\ftor
ped\fl when the engine st\frts.CAUTION:
.As soon as the engine has started, release
the ignition switch immediately.
. Do not operate the starter for more than 15
seconds at a time. If the engine does not
start, push the ignition switch to the “OFF”
position and wait 10 seconds before crank-
ing the engine again. Otherwise, the starter
could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
5. Allow the engine to idle for \ft le\fst 30 seconds \ffter st\frting the engine to w\fr\b-up. Drive \ft
\boder\fte speeds for \f short dist\fnce first,
especi\flly in cold we\fther.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
6. To stop the engine, \bove the selector lever to the“P” (P\frk) position (AT/CVT \bodel) or \bove the
shift lever to the “N” (Neutr\fl) position (MT \bodel) ,
\fpply the p\frking br\fke \fnd push the ignition
switch to the “OFF” position.
STARTING ENGINE (model with
Intelligent Key system)
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
DIESEL ENGINE
1. Apply the park\fng brake.
\b. Move the sh\fft lever to the “N” (Neutral) pos\ft\fon.The starter is designed to not operate unless
the clutch pedal is fully depressed.
The Intelligent Key must be carried when
operating the ignition switch.
3. Push the \fgn\ft\fon sw\ftch to the “ON” pos\ft\fon and wa\ft unt\fl the glow plug \fnd\fcator l\fght turns off.
Depress the clutch pedal and push the \fgn\ft\fon
sw\ftch to start the eng\fne.
To start the eng\fne \fmmed\fately, push and release
the \fgn\ft\fon sw\ftch wh\fle depress\fng the clutch
pedal w\fth the \fgn\ft\fon sw\ftch \fn any pos\ft\fon.
4. Immed\fately release the \fgn\ft\fon sw\ftch when the eng\fne starts. If the eng\fne starts, but fa\fls to run,
repeat the above procedures.
If the eng\fne \fs very hard to start \fn extremely cold
or hot weather, depress the accelerator pedal and
hold \ft. Push the \fgn\ft\fon sw\ftch for up to 15
seconds wh\fle hold\fng. Release the accelerator
pedal when the eng\fne starts.
CAUTION:
.As soon as the engine has started, release
the ignition switch immediately.
. Do not operate the starter for more than 20
seconds at a time. If the engine does not
start, push the ignition switch to the “OFF”
position and wait 20 seconds before crank-
ing the engine again. Otherwise, the starter
could be damaged. .
If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
5. Allow the eng\fne to \fdle for at least 30 seconds after start\fng the eng\fne to warm-up. Dr\fve at
moderate speeds for a short d\fstance f\frst,
espec\fally \fn cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
6. To stop the eng\fne, move the sh\fft lever to the “N”(Neutral) pos\ft\fon, apply the park\fng brake and
push the \fgn\ft\fon sw\ftch to the “OFF” pos\ft\fon.
DRIVING WITH AUTOMATIC TRANSMIS-
SION (AT)
The Automat\fc Transm\fss\fon (AT) \fn your veh\fcle \fs
electron\fcally controlled to produce max\fmum power
and smooth operat\fon.
The recommended operat\fng procedures for th\fs
transm\fss\fon are shown on the follow\fng pages. Follow
these procedures for max\fmum veh\fcle performance
and dr\fv\fng enjoyment.
CAUTION:
.The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up.
. Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Do not downshift abruptly on slippery roads.
This may cause a loss of control.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
your vehicle checked by a RENAULT dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idling speed while
shifting from the “N” (Neutral) position to
any driving position.
Starting and driving5-11
DRIVING VEHICLE
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
P (Park):
Use this position when the vehicle is parked or when
starting the engine.Make sure that the vehicle is
completely stopped and move the selector lever
into the P (Park) position. \fpply the parking brake.
When parking on a hill\b apply the parking brake first\b
and then move the selector lever into the P (Park)
position.
R (Reverse):
Use this position to back up. Make sure that the vehicle
is completely stopped before selecting the R (Reverse)
position.
N (Neutral):
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the N (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
Use this position for all normal forward driving.
2 (Second gear):
Use this position for climbing hills or engine braking on
downhill grades.
1 (Low gear):
Use this position when climbing steep hills slowly or
driving slowly through deep snow\b or for maximum
engine braking on steep downhill grades.
Do not shift into the gears when the vehicle speed
exceeds the following limits\b otherwise the engine may
over-rev and cause engine damage. Engine model
Selector lever position
12
HR12DE
km/h (MPH) 45 (28) 90 (56)
HR15DE
km/h (MPH) 50 (30)
95 (60)
Overdrive switch
JVS0013XLeft-Hand Drive (LHD) modelEach time the engine is started\b the overdrive function
is automatically reset to “ON”.
“ON” position:
With the engine running and the selector lever in the
“D” (Drive) position\b the transmission upshifts into the
overdrive as vehicle speed increases.
Overdrive does not engage until the engine has
reached operating temperature.
“OFF” position:
For driving up and down long slopes where engine
braking is necessary\b push the overdrive switch. The
overdrive off indicator light
in the meter panel
illuminates.
When cruising at a low speed or climbing a gentle
slope\b you may feel uncomfortable shift shocks as the transmission shifts into and out of the overdrive
repeatedly. In this case\b push the overdrive switch to
turn the overdrive “OFF”.
When driving conditions change\b push the overdrive
switch to turn the overdrive “ON”. The overdrive off
indicator light will turn off.
Remember not to drive at high speeds for extended
periods of time with the overdrive “OFF”. This reduces
fuel economy.
\fccelerator downshift - in D (Drive) position
For passing or climbing hills\b depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear\b depending on the vehicle speed.
Shift lock release
If the battery is discharged\b the selector lever may not
be moved from the “P” (Park) position even with the
foot brake pedal depressed.
To move the selector lever\b release the shift lock. The
selector lever can be moved to the “N” (Neutral)
position. However\b the steering wheel will be locked
unless the ignition switch is placed in the “ON”
position. This allows the vehicle to be moved if the
battery is discharged.
Starting and driving5-13
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-16Starting and driving
P (Park):
Use this position when the vehicle is par\fed or when
starting the engine.Make sure that the vehicle is
completely stopped and move the selector lever
into the \bP”(Park) position. Apply the par\fing
bra\fe. When par\fing on a hill, first depress the foot
bra\fe pedal, apply the par\fing bra\fe, and then move
the selector lever into the \bP” (Par\f) position.
R (Reverse):
Use this position to bac\f up. Ma\fe sure that the vehicle
is completely stopped before selecting the \bR”
(Reverse) position.
N (Neutral):
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the \bN” (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
Use this position for all normal forward driving.
L (Low):
Use this position when climbing steep hills slowly or
driving slowly through deep snow, sand or mud, or for
maximum engine bra\fing on steep downhill grades.SPORT mode switch
JVC0027XRight-Hand Drive (RHD) modelTo select the SPORT mode, push the SPORT mode
switch with the selector lever in the \bD” (Drive)
position. The SPORT mode indicator light
in the
meter panel illuminates. To turn off the SPORT mode,
push the SPORT mode switch again. The SPORT
mode indicator light will turn off. When the selector
lever is shifted to any position other than \bD”, the
SPORT mode will be automatically turned off.
“OFF” position:
For normal driving and fuel economy, use the \bOFF”
position.
“ON” position:
For driving up or down long slopes where engine
bra\fing is necessary, or for powerful acceleration, use
the \bON” position. The transmission will automatically
select a different gear ratio, allowing the engine to
provide high output.
When driving conditions change, push the switch to
turn the SPORT mode off.
Remember not to drive at high speeds for extended
periods of time with the SPORT mode in the \bON”
position. This reduces fuel economy.
Accelerator downshift - in the \bD” position -
For passing or climbing hills, depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear, depending on the vehicle speed.
Shift loc\f release
JVC0028XRight-Hand Drive (RHD) modelIf the battery charge is low or discharged, the selector
lever may not be moved from the \bP” (Par\f) position
even with the bra\fe pedal depressed and the selector
lever button pushed.
To move the selector lever, perform the following
procedure:
1. Model with Intelligent Key system:
Place the ignition switch in the \bOFF” or \bLOCK”
position.
Model without Intelligent Key system:
Place the ignition switch in the \bLOCK” position,
and remove the \fey if it is inserted.
2. Apply the par\fing bra\fe.
3. Depress the shift loc\f release button.
4. Push the selector lever button and move the selector lever to the \bN” (Neutral) position while
holding down the shift loc\f release.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5. Place the ignition switch in the “ON” \fosition tounlock the steering wheel.
\bhe vehicle may be moved to the desired location.
Re\flace the removed shift lock release cover after the
o\feration.
For model with Intelligent Key system: If the battery is
discharged com\fletely, the steering wheel cannot be
unlocked. Do not move the vehicle with the steering
wheel locked.
If the selector lever cannot be moved out of the “P”
(Park) \fosition, have a RENAUL\b dealer check the
CV\b system as soon as \fossible.
WARNING:
If the selector lever cannot be moved from the
“P” (Park) position while the engine is running
and the brake pedal is depressed, the stop lights
may not work. Malfunctioning stop lights could
cause an accident injuring yourself and others.
High fluid tem\ferature \frotection mode
\bhis transmission has a high fluid tem\ferature \frotec-
tion mode. If the fluid tem\ferature becomes too high
(for exam\fle, when climbing stee\f grades in high
tem\ferature with heavy loads, such as when towing a
trailer) , engine \fower and, under some conditions,
vehicle s\feed will be decreased automatically to
reduce the chance of transmission damage. Vehicle
s\feed can be controlled with the accelerator \fedal,
but engine and vehicle s\feed may be limited.
Fail-safe
When the fail-safe o\feration occurs, the CV\b will not
be shifted to the selected driving \fosition.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
place the ignition switch in the “OFF”position
and wait for 10 seconds. Then turn the ignition
switch back to the “ON”position. The vehicle
should return to its normal operating condition.
If it does not return to its normal operating
condition, have a RENAULT dealer check the
transmission and repair it if necessary.
WARNING:
When the fail-safe operation occurs, vehicle
speed may be gradually reduced. The reduced
speed may be lower than other traffic, which
could increase the chance of a collision. Be
especially careful when driving. If necessary, pull
to the side of the road at a safe place and allow
the transmission to return to normal operation,
or have it repaired if necessary.
DRIVING WI\bH MANUAL \bRANSMISSION
(M\b)
WARNING:
. Do not downshift abruptly on slippery roads.
This may cause a loss of vehicle control.
. Do not over-rev the engine when shifting to
a lower gear. This may cause a loss of
vehicle control or engine damage.
CAUTION:
.Do not rest your foot on the clutch pedal
while driving. This may damage the clutch
system.
. Fully depress the clutch pedal before shift-
ing to help prevent transmission damage.
. Stop the vehicle completely before shifting
into the “R” (Reverse) position.
. When the vehicle is stopped for a period of
time, for example waiting at stoplights, shift
to the “N” (Neutral) position and release the
clutch pedal with the foot brake pedal
depressed.
. Do not shift to the "N" (Neutral) position
while driving. Doing so may result in an
accident due to loss of engine braking.
Starting and driving5-17
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-30Starting and driving
Setting cruising speed
1. Acce\ferate to the desired speed.
\b. Push the SETíswitch and re\fease it.
3. The SET indicator \fight and set speed indicator i\f\fuminate on the meter pane\f and the vehic\fe
information disp\fay.
4. Take your foot off the acce\ferator peda\f.
The vehic\fe wi\f\f maintain the set speed.
Passing another vehicle:
Depress the acce\ferator peda\f to acce\ferate. After
re\feasing the acce\ferator peda\f, the vehic\fe wi\f\f return
to the previous\fy set speed.
The vehic\fe may not maintain the set speed when
going up or down steep hi\f\fs. In such cases, drive
without the cruise contro\f.
Resetting to slower speed:
Use any one of the fo\f\fowing methods to reset to a
s\fower speed.
. Light\fy tap the foot brake peda\f. When the vehic\fe
reaches the desired speed, push and re\fease the
SETí switch.
. Push and ho\fd the SETí switch. When the vehic\fe
reaches the desired speed, re\fease the SETí
switch.
. Quick\fy push and re\fease the SETí switch. This
wi\f\f reduce the vehic\fe speed by about 1 km/h or 1
MPH.
Resetting to faster speed:
Use any one of the fo\f\fowing methods to reset to a
faster speed.
. Depress the acce\ferator peda\f. When the vehic\fe
reaches the desired speed, push and re\fease the
SETí switch. .
Push and ho\fd the RES+ switch. When the
vehic\fe reaches the desired speed, re\fease the
RES+ switch.
. Quick\fy push and re\fease the RES+ switch. This
wi\f\f increase the vehic\fe speed by about 1 km/h or
1 MPH.
Resuming at preset speed:
Push and re\fease the RES+ switch.
The vehic\fe wi\f\f resume the \fast set cruising speed
when the vehic\fe speed is over 40 km/h (\b5 MPH) .
Cance\fing cruising speed
Use any one of the fo\f\fowing methods to cance\f the set
speed.
. Push the CANCEL switch. The SET indicator \fight
wi\f\f turn off.
. Tap the foot brake peda\f. The SET indicator \fight
wi\f\f turn off.
. Push the cruise contro\f MAIN switch. Both the
SET and cruise indicator \fights turn off.
WARNING:
.Do not stop or park the vehicle over
flammable materials such as dry grass,
waste paper or rags. They may ignite and
cause a fire.
. Safe parking procedures require that both
the parking brake be applied and the
selector lever placed in the “P ” (Park)
position (Automatic Transmission model/
Continuously Variable Transmission model)
or the shift lever placed in an appropriate
gear (Manual Transmission model) . Failure
to do so could cause the vehicle to move
unexpectedly or roll away and result in an
accident.
. When parking the vehicle, make sure the
selector lever is moved to the “P”(Park)
position. The selector lever cannot be moved
out of the “P ” (Park) position without
depressing the foot brake pedal.
. Never leave the engine running while the
vehicle is unattended.
. When parking for an extended period of time
with Stop/Start (Idling Stop) System (if
equipped) activated, the engine will restart
automatically. Never leave the vehicle with
the ignition switch in the “ON”position.
. Never leave children or adults who would
normally require the support of others alone
in the vehicle. Pets should not be left alone
either. They could unknowingly activate
switches or controls and inadvertently be-
come involved in a serious accident and
injure themselves. On hot, sunny days,
temperatures in a closed vehicle could
PARKING
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
quickly become high enough to cause se-
vere or possibly fatal illness to people and
animals.
SSD0488
Left-Hand Drive (LHD) model
SSD0489
Right-Hand Drive (RHD) model1. Firmly apply the par\fing bra\fe.
\b. Automatic Transmission (AT)/Continuously Vari-able Transmission (CVT) model: Move the selector
lever to the “P” (Par\f) position.
Manual Transmission (MT) model: Move the shift
lever to the “R” (Reverse) position. When par\fing
on an uphill grade, move the shift lever to the “1”
(1st) position. 3. To help prevent the vehicle from moving into traffic
when par\fed on an incline, it is a good practice to
turn the wheels as illustrated.
HEADED DOWNHILL WITH CURB
*1
Turn the wheels into the curb and move the vehicle
forward until the curb side wheel gently touches
the curb. Then apply the par\fing bra\fe. HEADED UPHILL WITH CURB
*2
Turn the wheels away from the curb and allow the
vehicle to move bac\f until the curb side wheel
gently touches the curb. Then apply the par\fing
bra\fe.
HEADED UPHILL OR DOWNHILL, WITHOUT
CURB
*3
Turn the wheels toward the side of the road so the
vehicle will move away from the center of the road
if the vehicle moves. Then apply the par\fing bra\fe.
4. Model with Intelligent Key system:
Place the ignition switch in the “OFF” position.
Model without Intelligent Key system:
Place the ignition switch in the “LOCK” position
and remove the \fey.
NOTE:
For Model with Stop/Start (Idling Stop) System:
Use this system when the vehicle is stopped for
a period of time, for example waiting at stop-
lights.
Stop the engine with the ignition switch when
parking, etc. for an extended period of time.
Starting and driving5-31
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
6-2In case of emergency
If you have a flat tire, follow the in\ftruction\f a\f follow\f.
S\bOPPING VEHICLE
WARNING:
.Be sure to apply the parking brake firmly.
. Be sure to move the shift lever to the “R”
(Reverse) position (Manual Transmission
(MT) model) .
. Be sure to move the selector lever to the “P”
(Park) position. (Automatic Transmission
(AT)/Continuously Variable Transmission
(CVT) model)
. Never change tires when the vehicle is on a
slope, ice or slippery area. This is hazardous.
. Never change tires when the oncoming
traffic is close to your vehicle. Call for
professional road assistance.
1. Safely move the vehicle off the road away from traffic.
2. \burn on the hazard indicator fla\fher light\f.
3. Park on a level \furface.
4. Apply the parking brake.
5. Automatic \bran\fmi\f\fion (A\b)/Continuou\fly Vari- able \bran\fmi\f\fion (CV\b) model: Move the \felector
lever to the “P” (Park) po\fition.
Manual \bran\fmi\f\fion (M\b) model: Move the \fhift
lever to the “R” (Rever\fe) po\fition.
6. \burn off the engine.
7. Open the hood and \fet up the warning triangle (if equipped):
.\bo warn other traffic.
.\bo \fignal profe\f\fional road a\f\fi\ftance per\fon-nel that you need a\f\fi\ftance.
8. Have all pa\f\fenger\f get out from the vehicle and \ftand in a \fafe place, away from other traffic and
clear of the vehicle.
PREPARING \bOOLS
SCE0902
Rai\fe the back door floor cover.
Your vehicle i\f equipped with either a \fpare tire or an
emergency tire puncture repair kit. Carefully read the
in\ftruction\f provided in the appropriate \fection. .
For model with \fpare tire: See “Changing flat tire
(for model with \fpare tire)” (P.6-2) .
. For model with emergency tire puncture repair kit:
See “Repairing flat tire (for model with emergency
tire puncture repair kit)” (P.6-5) .
CHANGING FLA\b \bIRE (for model with \fpare
tire)
SCE0913
Remove the jack, nece\f\fary tool\f and the \fpare tire
from the \ftorage area.
If \fpacer\f are equipped, remove them before removing
the \fpare tire.
Blocking wheel\f
MCE0001A
FLAT TIRE
&RQGLWLRQ