2012 RENAULT PULSE clock setting


> (GLW    0RGHO .$2(0B5HQDXOW @
17. AUX IN (auxiliary input\f jack
1\b. RPT (Repeat\f/MIX (Mix play\f button
19. TUNE/SEARCH button
Anti-theft system (if equipped\f
This unit can only be activated when the ignition switch
for Anti-Theft System is in the “ACC” or “ON” position.
Each radio is uniquely matched to the vehicle’s
immobilizer and therefore cannot be transferred to
any other vehicle.
Audio main operation
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
To turn on the audio system, push the POWER ON/
OFF button.
.The system will turn on in the mode, (radio or CD\f
which was used immediately before the system
was last turned off.
. If there is no CD loaded, the radio will be turned
on.
To turn off the audio system, push the POWER ON/
OFF button.
Volume control:
To control the volume, turn the VOLUME control dial.
Turn the VOLUME control dial clockwise to increase
the audio volume.
Turn the VOLUME control dial counterclockwise to
decrease the audio volume.
Sound preference button:
To enter the audio mode (radio or CD\f , push the
button. When no CD is loaded, the audio system will
automatically switch to the radio mode.
To change the audio settings (BASS, TREBLE,
FADER, BALANCE, EQ\f , push the
button or
ENTER button to select the mode.
BASS ?TREBLE ?BALANCE ?FADER ?EQ ?
BASS
To adjust each audio setting, turn the MENU/VOL
control dial clockwise or counterclockwise.
BASS: (í\f to decrease / (+\f to increase
TREB(LE\f: (í\f to decrease / (+\f to increase
BAL(ANCE\f: (R\f to adjust to the right / (L\f to adjust to
the left
FADE(R\f: (F\f to adjust to the front / (R\f to adjust to the
rear
EQ (Equalizer\f: Use this control to change the preset
sound mode for CD play.
Turn the MENU/VOL dial clockwise or counterclock-
wise. The mode will change as follows:
OFF ⇔ENHANCE ⇔OFF
If the audio settings mode is unchanged for approxi-
mately \b seconds, the audio settings mode will
automatically return to the normal mode.
Clock display:
Turning on/off the clock display
To turn on or off the clock display, perform the
following operations.
1. Push the MENU button while the audio system is on. ("PHONE SETUP" is displayed.\f 2. Turn the VOLUME control knob until "CLOCK"
appears on the display.
3. Push the ENTER button. ("CLOCK OFF" or "CLOCK ON" is displayed.\f
4. To turn on the clock display, turn the VOLUME control knob till "CLOCK ON" is displayed. To turn
off the clock display, turn the VOLUME control
knob till "CLOCK OFF" is displayed, and push
ENTER.
Clock adjustment
To adjust the time of the clock, perform the following
operations.
1. Push the ENTER button while "CLOCK ON" is displayed.
2. The hour display will flash.
3. Turn the VOLUME control knob to adjust the hour.
4. Push the ENTER button. The minute display will flash.
5. Turn the VOLUME control knob to adjust the minute.
6. Push the ENTER button to complete the clock adjustment.
AUX button:
The AUX IN jack is located on the audio unit. The AUX
IN audio input jack accepts any standard analog audio
input such as from a portable cassette tape player, CD
player, MP3 player or laptop computer.
Push the AUX button to play a compatible device when
it is plugged into the AUX IN jack.
RENAULT strongly recommends using a stereo mini
plug cable when connecting your music device to the
audio system. Music may not play properly when a
Heater and air conditioner, and audio system4-41
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
station and the actual playing mode will be interrupted\f
Once the news broadcast is finished, the unit returns
to the pre\bious mode\f
In some countries or regions, this ser\bice is not
a\bailable or the signal is too weak to be recei\bed\f
1\fNews standby mode
.The news standby mode can be acti\bated in
the FM or CD mode\f
.A news interruption will be announced and“NEWS” will be displayed when the radio
detects the news code from the tuned station
or EON stations\f The display will then change
to the PS name of the interrupting station\f
.When pushing the TA/NEWS button for longerthan 2 seconds, the news standby mode is
turned off and the indicator disappears from
the display\f
2\f News interruption mode
.When the TA/NEWS button is pushed during
the news interruption mode, the radio returns to
the pre\bious source\f Howe\ber, the news
standby mode is maintained\f
.When thebutton is pushed during the
news interruption mode, the radio changes to
the CD mode\f Howe\ber, the news standby
mode is maintained\f
If the radio band is changed to the MW or LW,
the news standby mode will be turned off\f
MENU button:
To configure Alternati\be Frequency, Regional and
Language settings, perform the following procedure:
1\f Push and hold the MENU button for at least 1\f5 seconds\f 2\f Turn the MENU/VOL dial clockwise or counter-
clockwise\f The display message will change as
follows:
AF⇔REG ⇔LANGUAGE ⇔AF
. To acti\bate or deacti\bate the AF and REG mode,
briefly push the ENTER button when AF or REG
appears on the display and turn the MENU/VOL
dial clockwise or counterclockwise to switch
between the off or on position\f After selection,
push the ENTER button to confirm the settings\f
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak\f
— When the REG mode is enabled, the audio unit will maintain and maintain the station which is
broadcasting local (regional) programmes\f
. To change the display language, briefly push the
ENTER button when LANGUAGE appears on the
display then turn the MENU/VOL dial clockwise or
counterclockwise to select the appropriate lan-
guage setting\f
ENGLISH ⇔DUTCH ⇔FRENCH ⇔SPANISH
⇔ GERMAN ⇔ITALIAN ⇔PORTUGUESE ⇔
ENGLISH
After selecting the preferred language, push the
ENTER button to exit the menu\f
To configure the SPEED \bolume and BEEP settings,
perform the following procedure:
1\f Push the MENU button\f
2\f Turn the MENU/VOL dial clockwise or counter- clockwise\f The display message will change as
follows:
PHONE SETUP ⇔SPEED VOL ⇔CLOCK ⇔
BEEP ⇔PHONE SETUP
For phone operation, see “Bluetooth
ŠHands-Free Phone System (if equipped for model without
na\bigation system)” (P\f4-56) \f
. When SPEED VOL appears on the display, briefly
push on the ENTER button then turn the MENU/
VOL dial clockwise or counterclockwise to adjust
the le\bel of the \bolume\f
Adjusting the setting to 0 (zero) turns off the
speed \bolume feature\f Increasing the speed
\bolume setting results in the audio \bolume
increasing more rapidly with \behicle speed\f Push
the ENTER button again to sa\be the setting\f
. When BEEP appears on the display, briefly push
the ENTER button and then turn the MENU/VOL
dial clockwise or counterclockwise to switch the
beep sound on or off\f Push the ENTER button
again to sa\be the setting\f
After the preferred le\bels ha\be been set, push the
MENU button to exit the menu or wait at least for 10
seconds without pressing any buttons\f
Heater and air conditioner, and audio system4-45
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Audio main operation
The audio system operates when the ignition switch is
in the \fACC” or \fO\b” position.
Power/VOL dial:
Power ON/OFF:
To turn on the audio system, push the
dial.
. The system will turn on in the mode, which was
used immediately before the system was turned
off.
. If a CD is inserted or a USB and/or an AUX device
is connected when the system is turned off, and if
the system is turned on again with the devices
removed or disconnected, the radio will turn on.
To turn off the audio system, push the
dial.
Volume control:
To control the volume, turn the
dial.
Turn the
dial clockwise to make the sound louder.
Turn the
dial counterclockwise to make the sound
quieter.
SETUP button:
To configure Audio, Clock, Bluetooth, Language or
Scroll direction settings, perform the following proce-
dure:
1. Push the
button.
2. Push the TU\bE/ME\bU/E\bTER dial.
3. Turn the TU\bE/ME\bU/E\bTER dial clockwise or counterclockwise. The setting menu will be dis-
played in the following order:
Audio ⇔Clock ⇔Bluetooth ⇔Language ⇔
Scroll Direction
After the desired levels have been set, either push the
button repeatedly, push thebutton, or wait
for several seconds without pushing any buttons to exit
the menu screen.
Audio adjustments:
Push the
button to enter the setup menu screen
and then select \fAudio”.
Each time the TU\bE/ME\bU/E\bTER dial is pushed, the
mode will change as follows:
BASS ?TREBLE ?BALA\bCE ?FADE ?AUX
VOL ?SPD VOL (if equipped) ?Audio (setup menu
screen) ?BASS
Turn the TU\bE/ME\bU/E\bTER dial clockwise or
counterclockwise to adjust the following items and
push the TU\bE/ME\bU/E\bTER dial to confirm.
Bass control:
Use this control to enhance or attenuate the bass
response sound.
Treble control:
Use this control to enhance or attenuate the treble.
Balance control:
Use this control to adjust the balance of the volume
between the left and right speakers.
Fader control:
Use this control to adjust the balance of the volume
between the front and rear speakers (if equipped) .
AUX VOL (Auxiliary volume) control:
Use this control to adjust the volume output from the
auxiliary source.
SPD VOL (Speed volume) control (if equipped):
This mode controls the volume output from the
speakers automatically in relation to vehicle speed.
Adjusting the setting to \f0” (zero) turns off the speed volume feature.
Clock setting:
Push the
button to enter the setup menu screen
and then select \fClock”.
Turn the TU\bE/ME\bU/E\bTER dial, the mode will
change as follows:
Set Time ⇔O\b/OFF ⇔Clock Format ⇔Set Time
Set Time:
Select \fSet Time” then adjust the clock as follows:
The hour display will start flashing. Turn the TU\bE/
ME\bU/E\bTER dial to adjust the hour and push the
TU\bE/ME\bU/E\bTER dial. The minute display will start
flashing. Turn the TU\bE/ME\bU/E\bTER dial to adjust
the minute and push the TU\bE/ME\bU/E\bTER dial to
finish the clock adjustment.
O\b/OFF:
Set the clock display to on or off when the audio unit is
turned off. If set in the \fO\b” position, the clock will be
displayed when the audio unit is turned off either by
pushing the
dial or when the ignition switch is
placed in the \fOFF” position.
Clock Format:
Switch the clock display between 24-hour and 12-
hour clock mode.
Bluetooth setting:
It is possible to set the Bluetooth settings. (See
\fBluetooth
Šaudio player operation” (P.4-52) .)
Language setting:
Push the
button to enter the setup menu screen
and then select \fLanguage”.
Select the appropriate language and push the TU\bE/
ME\bU/E\bTER dial. Upon completion, the screen will
automatically adopt the language setting.
Heater and air conditioner, and audio system4-47
&RQGLWLRQ