headrest................................................ (up to the end of the DU)
front seats adjustment ...................................... (up to the end of the DU)
adjusting your driving position .............. (up to the end of the DU)
1.15
ENG_UD18801_8
Appuis-tête avant (B74 - K74 - X81 - J81 - X91 - B91 - K91 - D91 - X\
95 - B95 - D95 - J95 - R95 - Renault)
ENG_NU_939-3_D91_Renault_1
Headrests - Seats
fRONT HEAdREsTs
To raise the headrest
Pull the headrest upwards to the de -
sired height.
To lower the headrest
Press button 2 and guide the headrest
down to the desired height.
To adjust the angle of the
headrest
Depending on the vehicle, tilt section A
towards or away from you to the re -
quired position.
To remove the headrest
Raise the headrest to its highest po -
sition (tilt the seatback backwards if
necessary). Press button 1 and lift the
headrest to release it.
To refit the headrest
Pull out the headrest rods 3 as far as
possible by pulling from the top. Take
care to ensure they are clean and cor-
rectly aligned and, if there are any prob-
lems, check that the notches are facing
forwards.
Insert the headrest rods into the holes
(tilt the seatback backwards if neces -
sary).
Lower the headrest until it locks, press
button 1 and lower the headrest as far
as possible.
Check that each headrest rod 3 is se -
curely locked in the seatback by trying
to pull them up or push them down.
The headrest is an impor -
tant safety component:
ensure that it is in place and
in the correct position. The
distance between your head and the
headrest and the distance between
the head and section A should be
as small as possible.
2
3
A1
The three upper positions can
be manipulated without pressing
button 2. However, it is preferable to
press this button to lower the head-
rest.
front seat adjustment ............................(up to the end of the DU)
front seats adjustment ...................................... (up to the end of the DU)
front seats with manual controls ........................................ (current page)
1.16
ENG_UD22179_4
Sièges avant à commandes manuelles (X91 - D91 - Renault)
ENG_NU_939-3_D91_Renault_1
Jaune NoirNoir texte
Depending on the vehicle, the following
may be available:
– front seats with manual controls;
– front seats with electric controls;
– lumbar adjustment for the driver ’s
seatback;
– heated seats;
– driver’s seat position storage (refer
to “Driver’s seat with storage func -
tion” in Section 1).
fRONT sEATs (1/2)
manual controls
To move the seat forwards or back
Lift handle 1 to release. Release the
handle once the seat is in the correct
position and ensure that the seat is fully
locked into position.
To raise or lower the seat base
Move lever 3 as many times as neces-
sary upwards or downwards.
To tilt the seatback
Turn control knob 2 to the required po-
sition.
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
We would advise you not to recline
the seatbacks too far to ensure that
the effectiveness of the seat belts is
not reduced.
Nothing should be placed on the
floor (area in front of driver) as such
objects may slide under the pedal
during braking manoeuvres, thus
obstructing its use.
1
3
2
Electric controls
To move the seat base forwards or
back, move switch 4 forwards or back-
wards.
To raise or lower the rear of the seat
base , move the rear of switch 4 up or
down.
To raise or lower the front of the seat
base, move the front of switch 4 up or
down.
4
heated seats .......................................................... (current page)
JauneNoirNoir texte
1.17
ENG_UD22179_4
Sièges avant à commandes manuelles (X91 - D91 - Renault)
ENG_NU_939-3_D91_Renault_1
8
Lumbar adjustmentLower handle 8 to increase the support
and lift it to decrease it.
Heated seatsWith the engine running, turn control 5
to either position 1, 2 or 3 (depending
on the temperature required). An in -
dicator light on the instrument panel
lights up once the front seat heating
system is operating.
The system, which has a thermostat,
decides whether or not the heating is
needed, according to the position se -
lected.
Electric controls (continued)
Adjusting the seatback:
To tilt the seatback , move the top of
switch 7 forwards or backwards.
storage of the seat position
On equipped vehicles, buttons 6 are
used to store the driving positions (refer
to the following page).
fRONT sEATs (2/2)
57
6
force limiter
If an object is obstructing the seat, an
integrated force limiter stops the seat’s
travel. In this case, reverse the seat’s
travel, remove the object and move the
seat again.
Ensure that nothing is ob -
structing the movement of
the front seats.
front seatdriver’s position memory .................................. (current page)
1.19
ENG_UD14262_5
Mémorisation du siège conducteur (X91 - B91 - K91 - Renault)
ENG_NU_939-3_D91_Renault_1
dRIvER’s sEAT WITH pOsITION mEmORY
It is possible to store three driving po-
sitions.
A driving position includes the settings
for the driver’s seat base and seatback
and the door mirrors.
Operation
The storage of the driving position and
the recall of the driving position by
pressing the buttons are possible:
– with the “hands-free” card de -
tected or, depending on the vehicle,
RENAULT card in the card reader;
– when the driver’s door is opened.
storing your driving positionAdjust the seat using switches 4 and 5
(see previous page).
Adjust the door mirrors (refer to the
information on “Rear view mirrors” in
Section 1)
Press button 1 , 2 or 3 until you hear
a beep: the driving position (seat and
door mirrors) is stored.
To store other driving positions, repeat
this procedure for each of buttons 1, 2
and 3.
Recalling a stored driving
position
With the vehicle stationary , briefly
press button 1, 2 or 3 depending on the
required stored driving position.
Note: recall of the stored driving po -
sition is interrupted if one of the seat
adjustment buttons is pressed during
recall.
When driving, it is not possible to
recall a driving position.
1
23
4
5
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
We would advise you not to recline
the seatbacks too far to ensure that
the effectiveness of the seat belts is
not reduced.
Nothing should be placed on the
floor (area in front of driver) as such
objects may slide under the pedal
during braking manoeuvres, thus
obstructing its use.
seat belts .............................................. (up to the end of the DU)
adjusting your driving position ............................... (current page)
driving position settings ............................................................ (current page)
1.20
ENG_UD25429_7
Ceintures de sécurité (X91 - D91 - Renault)
ENG_NU_939-3_D91_Renault_1
Jaune NoirNoir texte
Always wear your seat belt when trav-
elling in your vehicle. You must also
comply with the legislation of the par -
ticular country you are in.
Before starting the vehicle:
– for the driver, first adjust your
driving position;
– then, ask all passengers to adjust
their seat belt to provide maxi -
mum protection.
Seat belts
Adjusting your driving
position
– s it well back in your seat (having
first removed your coat or jacket).
This is essential to ensure your back
is positioned correctly;
– adjust the distance between the
seat and the pedals. Your seat
should be as far back as possible
while still allowing you to depress
the clutch pedal fully. The seatback
should be adjusted so that your arms
are slightly bent when you hold the
steering wheel;
– adjust the position of your head -
rest. For maximum safety, your head
must be as close as possible to the
headrest;
– adjust the height of the seat. This
adjustment allows you to select the
seat position which offers you the
best possible view;
– adjust the position of the steering
wheel.
Adjusting the seat belts
Sit with your back firmly against the
seatback.
Shoulder strap 1 should be as close as
possible to the base of the neck but not
on it.
Lap belt 2 should be worn flat over the
thighs and against the pelvis.
The belt should be worn so that it is
as close as possible to your body, ie.:
avoid wearing heavy clothing or keep -
ing bulky objects under the belts, etc.
sEAT BELTs (1/3)
1
2
Seat belts which are incor -
rectly adjusted or twisted
may cause injuries in the
event of an accident.
Use one seat belt per person,
whether child or adult.
Even pregnant women should wear
a seat belt. In this case, ensure that
the lap belt is not exerting too much
pressure on the abdomen, but do
not allow any slack.
rear view mirrors ................................... (up to the end of the DU)
1.63
ENG_UD27731_1
Rétroviseurs (X91 - D91 - Renault)
ENG_NU_939-3_D91_Renault_1
Rear-view mirrors
folding door mirrors
The door mirrors automatically fold in
when the vehicle is locked (switch 2 in
position B ). In this case, they will fold
out when the ignition is next switched
on.
In any case, you can make the door
mirrors fold in (switch 2 in position C) or
fold out (switch 2 in position A).
Automatic mode is then deactivated. To
reactivate it, position switch 2 to B.
REAR vIEW mIRRORs (1/2)
door mirrors
Adjustment
Select the door mirror using switch 3 ,
then use button 1 to adjust it to the de-
sired position.
Heated door mirrors
Mirror de-icing is carried out at the
same time as rear screen de-icing.
storing the setting
For vehicles fitted with a driver’s seat
with position memorisation, refer to the
information on the “driver ’s seat with
position memory” in Section 1.
The driver ’s door mirror
may have two clearly de -
fined zones. Zone E shows
what can normally be seen
in an ordinary rear view mirror.
Zone D increases rear side visibility.
The objects in zone D look much
further away than they really are.
1
2
A
c
B
dE
3
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
1.64
ENG_UD27731_1
Rétroviseurs (X91 - D91 - Renault)
ENG_NU_939-3_D91_Renault_1
Rear view mirrors which tilt
in reverse gear
For vehicles equipped with the driver’s
seat with position memory, you can tilt
the door mirrors when reversing and
store the position.
setting and storage
With the vehicle stationary and reverse
gear engaged, select the door mirror
using switch 3 then, with button 1 ,
adjust it to the required position. Store
the position (refer to the information on
the “Driver’s seat with position memory”
in Section 1). Recalling the memorised position
With the vehicle stationary and re
-
verse gear engaged, select the door
mirror using switch 3 and then briefly
press the memory button chosen pre -
viously (refer to the information on the
“Driver’s seat with position memory” in
Section 1).
Returning to the driving position
The door mirrors return in one of the fol-
lowing situations:
– 10 seconds after having come out of
reverse gear;
– speed above 6 mph (10 km/h);
– engine switched off;
– switch 3 in the neutral position.
Interior rear view mirror 4
Its position can be adjusted.
The rear view mirror darkens automati-
cally at night if you are being followed
by a vehicle with its lights on.
1
3
dOOR mIRRORs (2/2)
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
4
7.2
FRA_UD29933_4
Index (X91 - D91 - Renault)
ENG_NU_939-3_D91_Renault_7
Jaune NoirNoir texte
AlphAbeticAl index (2/5)
driving position
settings ........................................................................ 1.20
e
electric windows ..................................................... 3.11 – 3.12
electronic parking brake ............................... 1.47, 2.12 → 2.14
electronic stability control: ESC .............................2.22 → 2.26
emergency brake assist ......................................... 2.22 → 2.26
emergency braking ................................................ 2.22 → 2.26
emergency key ........................................................... 1.2 – 1.3
emergency spare wheel ...................................................... 5.2
engine technical specifications .................................................. 6.6
engine oil .................................................................... 1.47, 4.4
engine oil capacity ...................................................... 4.6 – 4.7
engine specifications ........................................................... 6.6
engine standby .......................................................... 2.6 → 2.8
engine start/stop button ............................................. 2.3 → 2.5
environment ....................................................................... 2.18
ESC: electronic stability control .............................2.22 → 2.26
external temperature ......................................................... 1.62
F
faults operating faults ................................................ 5.28 → 5.32
filter air filter ......................................................................... 4.10
diesel filter .................................................................... 4.10
oil filter .................................................................. 4.7, 4.10
particle filter ................................................................. 1.49
passenger compartment filter ...................................... 4.10
fittings .................................................................... 3.15 → 3.18
front passenger air bag deactivation ................................. 1.38
front seat driver’s position memory .............................................. 1.19
front seat adjustment .............................................. 1.16 – 1.17front seats
adjustment .......................................................1.15 → 1.17
with manual controls .................................................... 1.16
fuel advice on fuel economy ............................................... 2.15
capacity ........................................................................ 1.71
filling ......................................................... 1.48, 1.71 – 1.72
grade ................................................................. 1.71 – 1.72
fuel economy ......................................................... 2.15 → 2.17
fuel level ............................................................................ 1.50
fuel tank capacity ............................................................. 1.71 – 1.72
fuel tank capacity .................................................... 1.71 – 1.72
fuses ....................................................................... 5.19 – 5.20
G
gear lever ........................................................................... 2.11
h
hands-free telephone integrated control ............................ 3.25
hazard warning lights signal ................................... 1.65 – 1.66
headlight flashers .............................................................. 1.65
headlight washer ............................................................... 1.70
headrest .................................................................... 1.15, 3.20
heated seats ............................................................. 1.17, 1.49
heating and air conditioning system .................................. 3.10
heating system .......................................................... 3.4 → 3.9
Hill Start Assist....................................................... 2.22 → 2.26
horn ................................................................................... 1.65
horn: flash ............................................................................. 1.65
sounding the horn ........................................................ 1.65
hubcap tool .......................................................................... 5.8
i
indicators .................................................................. 1.46, 1.65