Page 88 of 168
Practical information
86
Check the compatibility of the charging station and its charging cable with your vehicle.
)
Press latch 4to open the socket cover. )
Ensure that there is no foreign body on the
vehicle's charging socket.
Fast charging *
)Apply the parking brake and put the drive
selector in position P.P )Switch off all electrical consumers and turn
the ignition switch to the "LOCK"position. )Pull lever 3 , located alongside the driver's
seat, outer side, to open the access flap for
the fast char
ging socket (left hand side of
the vehicle).
Do not touch the metal end of thenormal charging socket or of thecharging cable. Risk of electrocution and/or faults.
)Connect the charging cable of the charging station to the vehicle following the
instructions on use of the station.
*
Depending on equipment.
Page 92 of 168
Practical information
90
Charging the battery using
a battery charger
)Star t the other vehicle and wait a fewminutes. )Turn the ignition key on your vehicle, until
the "Ready" lamp comes on.
)Disconnect the cables in the reverse order. )Refit the battery protective cover and
tighten the fixing screw.
I
f the "Ready" lamp does not come on, proceedas follows: )Leave the cables connected. )Return the ignition switch on your vehicle to
the " LOCK" position. )Put the main battery on charge, followingthe procedure for normal charging (see the"charging the main battery" section). )When the charging warning lamp in
the instrument panel comes on fixed,disconnect the cables. )Leave the battery on charge for at least one hour. )Turn the ignition key on your vehicle, until
the "Ready" lamp comes on.
If the problem persists, contact a
PEUGEOT dealer or a qualified workshop.
)
Remove the protective cover from thebattery.
Ensure that the electrolyte is not frozen.Check the electrolyte level and top upwith distilled water if necessary (refer tothe "checking levels" section).
)Slacken nut 1
and lift off the retaining bar.
Page 93 of 168
8
Practical information
91
Never charge the battery without first disconnecting the terminals and removing it from the vehicle.Do not disconnect the terminals whenthe "Ready" lamp is on, nor when thevehicle is being charged.
Before disconnecting
You must wait 2 minutes after switchingoff the ignition before disconnecting the battery.
Batteries contain harmful substancessuch as sulphuric acid and lead. Theymust be disposed of in line with legal requirements and never put out withhousehold waste. Ta k e used batteries to an authorisedcollection point.
)Disconnect the negative (-) terminal. )Lift the protective cover on the (+) terminal 2 . )Slacken nut 3. )Disconnect the positive (+) terminal. )Remove the battery. )Charge the battery following the
instructions given by the manufacturer of
the battery charger. )Reconnect the battery starting with the (+) cable.
After reconnecting
After reconnecting the battery, switchon the ignition and wait 1 minutebefore starting, to allow initialisation of the electronic systems. However, if minor problems persist after doingthis, contact a PEUGEOT dealer or a qualified workshop.Remember to enter the radio code yourself, referring to the relevant section.
Ensure that the battery posts and cable terminals are clean. If they are coveredwith sulphates (whitish or greenish deposit), disconnect and clean them.
Page 96 of 168
Practical information
94
Repair procedure
1. Sealing
)Switch off the ignition. )Indicate on the speed restriction sticker provided, the wheel to be repaired, then fix it to the steering wheel as a reminder that a
wheel is in temporary use. )Shake the sealant car tridge, remove the cap and screw on the injection pipe.
) Remove the valve cap for the tyre to be
repaired. ) Remove the valve core using the tool
provided, and store in in a clean place.
) Connect the injection pipe to the valve of
the tyre to be repaired.
)Tap the sealant car tridge (top down)several times with your hand, so as to injectall of the product into the tyre. )Remove the injection pipe. )Refit the valve core and tighten it using the
tool provided.
Take care, this product is harmful (e.g. ethylene-glycol, colophony...) if swallowed andcauses irritation to the eyes.Keep it out of reach of children. The use-by date of the sealant is marked on the car tridge.
After use, do not discard the empty cartridge but take it to a PEUGEOT dealer (France) or
an authorised waste disposal site. Don't forget to obtain a replacement cartridge; they are available from a PEUGEOT dealer or a qualified workshop.
Avoid removing any foreign bodieswhich have penetrated into the tyre.
Page 97 of 168
8
Practical information
95
2. Infl ation
)Check that the compressor switch A
is in
the "OFF" position. )Uncoil the compressor pipe B.
)
Connect this pipe to the valve of the
repaired wheel. )
Connect the compressor's electric plug to
the vehicle's 12 V socket (ignition switch in
position "ON" or "ACC"). ) Star t the compressor by turning the
switch A
to the "ON" position. )
Using the compressor, adjust the pressure in accordance with the vehicle's tyre
pressure label (located in the driver's door
aperture).
A loss of pressure indicates that the
puncture has not been fully plugged;contact a PEUGEOT dealer or a qualified
workshop for assistance.
) Remove the compressor and stow the kit. )
Drive off straight away at reduced speed (50 mph [80 km/h] max) limiting
the distance travelled to approximately120 miles (200 km).
As soon as possible, go to a PEUGEOT dealer or a qualified workshop. Tell the technician that you have used the kit. After checking, the technicianwill advise you whether the tyre can berepaired or must be replaced.
If after around 5 to 7 minutes the pressure is not attained, this indicates that the tyre is not repairable; contacta PEUGEOT dealer or a qualifiedworkshop for assistance.
Page 98 of 168
Practical information
96
Changing a wheel
To o l s r equired
- A jack: for lifting the vehicle.
- A wheelbrace: for removin
g and refitting
the wheel bolts.
- A handle: for operating the jack.
These tools are not supplied with your vehicle.
Parking the vehicle
Immobilise the vehicle where it does notblock traffic: the ground must be level,stable and not slippery. Apply the parking brake, switch off the ignition and put the drive selector in
position Pto lock the wheels.
If necessary, place a chock under thewheel diagonally opposite the wheel to be changed.
You must ensure that the occupants get out of the vehicle and wait where they are safe. Never go underneath a vehicle raised using a jack; use an axle stand.
Wheel with wheel trim
When removing the wheel , firstremove the wheel trim using the wheelbrace, by pulling at the valve hole.When fitting the wheel, refit the wheeltrim star ting by aligning the valve hole
with the valve, and then press on theedge of the trim with the palm of your hand.
Page 109 of 168
8
Practical information
107
Changing a fuse
the fusebox cover in the dashboard (left handside).
For access: )Unclip the cover and remove it completely by pulling it towards you. )Remove the tweezer.
Access to tools
Before changing a fuse, the cause of the failure
must be identified and rectified. ) Check that the ignition switch is in the "LOCK" position. )
Identify the faulty fuse by checking thecondition of its filament.
Changing a fuse
Good Failed
)
Use the special tweezer to extract the fuse from its location. )
Always replace the faulty fuse with a fuse
of the same rating. ) Check that the number etched on the box,
the rating etched on the top and the tablesbelow all agree.
PEUGEOT will not accept responsibilityfor the cost incurred in repairing your vehicle or for rectifying the malfunctionsresulting from the installation of accessories not supplied and not recommended by PEUGEOT andnot installed in accordance with itsinstructions, in par ticular when the consumption of all of the additional equipment connected exceeds 10 milliamperes.
Your vehicle's electrical system isdesigned to operate with standard or optional equipment.
Before installing other electrical equipment or accessories in your vehicle, contact a PEUGEOT dealer or a qualified workshop.
Page 138 of 168
03
136
CD, USB
AUDIO
PLAYING A COMPILATION
Insert an MP3 compilation in the CD pla
yer or connect a memory stick to the USB port.
The system creates playlists
(temporary memory) the creation timefor which can take from a few seconds to several minutes.
The pla
ylists are updated every time the ignition is switched off or aUSB memory stick is connected.
Pla
y starts automatically after a period which depends on the capacity of the USB memory stick.
At a fi rst connection, the order suggested is by folder.When connecting again, the order previously chosen is retained.
To pla
y a disc or memory stick whichhas already been inserted, press SRC/TELseveral times in succession and select " CD
" or " USB".
Press one of the buttons to select the next or previous track.
Pr
ess one of the buttons to select the next or previous folder in the order chosen.
Pr
ess and hold one of the buttons for
fast forwards or backwards.
