2012 Peugeot iOn change time

1
Instruments and controls
29
Service indicator
When the ignition is switched on, pressbutton A
several times in succession until the
ser vice indicator is displayed in the desiredunits. This point can be indicated in one o
f two ways:
- the miles (km) remaining,
- the time remaining to the next ser vice.



Operation
1.
The screen indicates that 620 miles (10 0 0 km) or 1 month remain before thenext service. 2.The screen indicates that the date for theservice has been exceeded.
Every time the ignition is switched on,
the ser vice spanner is displayed for a
few seconds to remind you that a ser vice should be carried out as soon as possible.3.Once the ser vice has been carried out, the
distance or the number of months to the next ser vice is displayed again.

System which informs the driver when the next service is due in accordance with the
manufacturer's servicing schedule.
The point at which the next ser vice is due is calculated from the last service indicator zeroreset.
S
ystem for manual adjustment of the brightness of the instruments and controls in relation to theexterior brightness.
With the lighting on or off, press button Ato select the function, then hold down to change
the intensity of the lighting of the instruments
and controls in "day" or "night" mode.
The intensity of the lighting increases each timebutton Ais pressed.
When the lighting reaches the maximumsetting, press again to change to the minimum setting.
When the lighting reaches the required
intensity, release button A .
The setting is saved when you release button A
and retained when the ignition switch is turned
to OFF.
Lighting dimmer

Instruments and controls
30
This function gives an estimate of the number
of miles (km) that your vehicle can still cover,
based on the recent conditions of use (driving style, use of heating, air conditioning...).
Range indicator
When the remaining range falls to a low level,"---"
is displayed in the instrument panel.
The display of "---", indicating that theservice date has arrived, comes on automatically after a cer tain time and distance travelled. The screen then indicates the time remaining before the next service is due.

Resetting the service indicator to zero
After each ser vice, the ser vice indicator shouldbe rest to zero.
The procedures is as follows: )Switch off the ignition (switch in the LOCK
or ACC position).
)Press the reset button A
several times in succession until the service indicator is
displayed. )Press and hold the reset button for a fewseconds until the spanner flashes.)Press the reset button while the spanner is flashing to change the display from "---"
to"CLEAR".The distance (or time) remaining before thenext ser vice is due is displayed.

8
Practical information
103
Changing dipped beam headlamp bulbs
)Turn the bulb holder to the left and pull it out. )Remove the bulb by pressing on the
tongue.)Change the bulb.
To r efit, carry out these operations in reverse order.








Changing front foglamp bulbs / daytime running lamp bulbs
)
Put the front wheels onto full lock, to facilitate access.)
Remove the clips securing the protective covers on the bulb holders.)
Move the cover aside.
)
Turn the bulb holder ( Afor the front fog
lamp, B for the daytime running lamp) to
the left and pull it out.
) Pull the bulb out and change it.
To reassemble, carry out these operations in
reverse order.

8
Practical information
111

Access to the fuses
)Open the bonnet (refer to the "Checks" section),)Unclip the cover and remove it completely
by pulling towards you. )Change the fuse (refer to the corresponding paragraph).)When you have finished, close the cover carefully to ensure sealing of the fusebox.
Fuse N°RatingFunctions
1110 A On-board charger.
12 10 A
Dir
ection indicator.
1
310 A Horn.
1410 A Daytime running lamps.
1515 A
Battery fan.
1610 A
Air conditioning compressor.
1720 A Right hand dipped beam.
1820 A
Left hand dipped beam, headlamp adjusters.
1
910 A
Right hand main beam.
20 10 A
Left hand main beam.

02
131
RADIO
Press SRC/TEL several times insuccession and select the FM1 or FM2radio band.
Press a button to listen to the corresponding preset station.Select the desired radio station and confi rm by pressing "OK".







RADIO

Press LIST
to display the list of stations received in alphabetical order.
The exterior environment
(hills, buildings, tunnel, car park, below ground...) may prevent reception, even in RDS station tracking mode.This phenomenon is normal in the propagation of radio waves and is in no way indicative of a fault with the audio system.

A long press on LIST
builds or updates
the list of stations; audio reception is cut
momentarily.
Make a long press on one o
f the buttons
to preset the station being heard.
The name of the station is displayedaccompanied by an audible signal to confi rm the preset.

A press changes to the next or previous
letter (e.g. A, B, D, F, G, J, K, ...). MANAGE THE LIST
PRESETTING AND SELECTING A STATION