Page 137 of 332
135
5
Visibility
Switching off
The manual guide-me-home lighting switchesoff immediately if you.
- flash the headlamps again,
- place the lighting control stalk in another
position,
- switch the ignition on (or select "ON" mode
for vehicle with the "Keyless Entry and Starting" system).
Manual guide-me-home
lighting
Switching on
)
Place the lighting control stalk in the "OFF"
position, or "AUTO" for vehicles that have it. ) Place the ignition switch on "LOCK" and remove the key (or select "OFF" mode for
vehicles that have the "Keyless Entry andStarting" system). ) Within one minute after switching off the
ignition, "flash" the headlamps using the lighting control stalk.
The headlamps come on for around30 seconds. ) A further "headlamp flash" within 60 seconds of switching the ignition to OFF (or selection of "OFF" mode for vehicles
with the "Keyless Entry and Star ting" system) reactivates the function for a
further 30 seconds. Te m p o r a r i l
y keeping the dipped beam headlamps
on after the vehicle's ignition has been switched
o
ff makes the exit of the vehicle's occupants easier
when the light is poor.
The duration of the guide-me-home
lighting can be set in the colour screen"Equipment" menu.
Page 138 of 332
136
Visibility
Exterior welcome lighting Remote switching on of the lighting makes your approach to the vehicle easier in poor light.
It comes on when the vehicle is unlocked remotely.
Switching on
) Place the lighting control in
position "OFF" or "AUTO".
) Press the open padlock on the
remote contro
l or the electronic key.
The sidelamps come on for about 30 seconds. For vehicles fitted
with automatic illumination of
headlamps, the welcome lightingonly comes on under conditions of low ambient light.
Switching off
The welcome lighting goes off immediately if:
- you press the open padlock on the remote control,
- you place the lighting control in another position,
- you switch on the ignition (or select "ON"
mode for vehicles fitted with the "Keyless
Entry and Star ting" system).
It is possible to choose the type of lamps switched on or to deactivatethe function via the colour screen"Equipment" menu.
Page 141 of 332
139
5
Visibility
Certain windscreen wiper functions(intermittent operation, ...) can beconfigured via the colour screen"Equipment" menu.
Manual controls
Windscreen wipers
B.
intermittent operation or rain sensor sensitivity adjustment ring.
Windscreen wash
Pull the wiper stalk towards you. Thewindscreen wash then the wipers operate for aset time. The headlamp wash is also activated if the
dipped beam headlamps are on.
Headlamp wash
Press the end of the lighting stalk to activate
the headlamp wash, when the dipped beam
headlamps are on. sin
gle wipe.
park.
intermittent
(the speed can be set
manually).
or
automat
ic rain sensitive wipers(the speed can be set manually).
slow.
f
ast.
A
. wiping speed selection stalk:
Y
ou can increase or decrease:
- the wiping frequency when the intermittent
mode is active,
- the sensitivit
y of the rain sensor when theautomatic mode is active.
- "+": high sensitivity.
- "-": low sensitivity.
To reduce the consumption of screenwash fluid, the headlampwashers only operate with the firstoperation of the screenwash.
Page 148 of 332
146
Safety
Group of supplementary systems which helpyou to obtain optimum braking in complete safety in emergency situations:
- anti-lock braking system (ABS),
- electronic brake force distribution (EBFD).
Braking assistance systems
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the stability and
manoeuvrability of your vehicle when braking,
in par ticular on poor or slippery surfaces.
Activation
The anti-lock braking system is active if the
vehicle speed is higher than 6 mph (10 km/h).
It is deactivated when the vehicle speed falls
below 3 mph (5 km/h).
The anti-lock braking system comes into
operation automatically when there is a risk of
wheel lock.
Normal operation of the ABS may make itself felt by slight vibration of the brake pedal.
Operating fault
When the vehicle is stationar
y
If this warning lamp comes on, accompanied by
the indication on the instrument panel screen, it
indicates a malfunction of the anti-lock brakin
gsystem which could result in a loss of control of
the vehicle when braking.
The vehicle retains normal braking.
Drive carefully at moderate speed and contact
a PEUGEOT dealer or a qualified workshop assoon as possible.
When braking in an emergency, pressvery firmly without releasing thepressure.
The warning lamp comes on for a fewseconds when the ignition is switched on (ON position). If it does not switch off or does not come on, contact a PEUGEOT dealer or a qualified workshop.
Page 149 of 332
147
6
Safety
When the vehicle is moving
If this warning lamp comes
on continuously it indicates a
malfunction of the anti-lock brakingsystem which could result in a loss of control of the vehicle on braking.
The two warning lamps comes on at the same time and the two warnings aredisplayed alternately in the instrumentpanel screen. When replacing wheels (tyres and rims), ensure that they conform to themanufacturer's recommendations.
The vehicle retains normal braking.
Drive carefully at moderate speed and contact
a PEUGEOT dealer or qualified workshop assoon as possible. I
f these two warning lamps come on, linked with
the warnings on the instrument panel screen,
the
y indicate a malfunction of the electronic brake force distribution which could result in a loss of control of the vehicle on braking.
You must stop as soon as it is safe to do so.Contact a PEUGEOT dealer or a qualifiedworkshop.
Page 188 of 332
186
Practical information
Changing a fuse
The extraction tweezer and spare fuses are
fitted in the engine compar tment fusebox.
To gain access to them: )Open the bonnet (refer to the "Checks"
section).
)Unclip the and remove the cover. )Remove the tweezer. )Carefully close the cover to ensure correct
sealing of the fusebox.
Access to the tools
Before changing a fuse, the cause of the failure
must be identified and rectified. ) Check that the switch is in the "LOCK"position or that the vehicle mode is "
OFF". )
Identify the faulty fuse by checking thecondition of its filament. )
Use the special tweezer to extract the fuse from its location. )
Always replace the faulty fuse with a fuse of the same rating. )
Check that the number etched on the box,
the rating etched on the top and the tablesbelow all agree.
Changing a fuse
Good Failed
PEUGEOT will not accept responsibilityfor the cost incurred in repairing your vehicle or for rectifying the malfunctionsresulting from the installation of accessories not supplied and notrecommended by PEUGEOT andnot installed in accordance with its instructions, in par ticular when theconsumption of all of the additionalequipment connected exceeds 10 milliamperes.
Your vehicle's electrical system isdesigned to operate with standard or optional equipment.
Before installing other electrical equipment or accessories in your vehicle, contact a PEUGEOT dealer or a qualified workshop.
The replacement of a fuse not mentioned in the following tables may cause a serious fault on your vehicle.Contact a PEUGEOT dealer or a
qualified workshop.
Page 198 of 332
196
Practical information
Recovering the vehicle
Recovery of your vehicle
2 wheel drive (2WD) versions: towing
with the wheels on the ground
)Put the gear lever into neutral (position Nfor the CVT gearbox). )Unlock the steering by by turning the ignition switch to the " ON
" position (or
to " ON " mode for vehicle fitted with the
"Keyless Entry and Starting" system). )Release the parking brake. )Switch on the hazard warning lamps on both vehicles. )Move off gently and travel slowly for a shor t
distance only.
General
recommendations
Obser ve the legislation in force in your country.
Ensure that the weight of the towing vehicle is higher than that of the towed vehicle.
The person at the wheel of the towed vehicle must have a valid drivinglicence.
When towing a vehicle with all four wheels on the ground, always use anapproved towing bar; rope and strapsare prohibited.
When towing a vehicle with the engine off, there is no longer any power assistance for braking or steering.
In the following cases, you must always call on a professional recovery service:
- vehicle broken down on a motor way or fast road,
- 4 wheel drive vehicle,
- when it is not possible to put the gearbox into neutral, unlock the steering, or release the parking brake,
- towing with only two wheels on the ground,
- where there is no approved towing bar available...
To w i ng with the wheels on the groundis only possible on 2 wheel drive (2WD) versions.
)
Fit the towing bar to the towing eye on thechassis, located under the front bumper.
Page 199 of 332
197
7
Practical information
Vehicles fitted with the 4 wheel drive
system must always be recovered on aflatbed.
Never have the vehicle towed with thefour wheels on the ground, this could damage the transmission.The vehicle must not be towed with the front or rear wheels on the groundevenif it is in front "2WD" (2 wheeldrive) mode.
4 wheel drive (4WD) versions: recovery on a fl atbed
