2012 Peugeot 301 clutch

1
25
Instruments and controls
Warning / indicator lampStateCauseAction / Observations
Diesel engine pre-heating fixed. The ignition switch is at the
2nd position (ignition on). Wait until the warning lamp goes off before star ting.
The period of illumination of the warning lamp is
determined by the climatic conditions (up to about
thir ty seconds in extreme climatic conditions).
If the engine does not star t, switch the ignition off and
then on, wait until the warning lamp goes off again,
then start the engine.
Parking brake fixed. The parking brake is applied or notproperly released. Release the parking brake to switch off the warninglamp, keeping your foot on the brake pedal.
Obser ve the safety recommendations.
For further information on the parking brake, refer to
the "Driving" section.
Foot on thebrake pedal fixed. The brake pedal must be pressed. With an electronic gearbox, press the brake pedal to start the engine (lever in position N).
With an automatic gearbox, with the engine running,
press the brake pedal before releasing the parking
brake, to unlock the lever and come out of position P . PIf you wish to release the parking brake without pressing the brake pedal, this warning lamp will
remain on.

flashin
g. With an electronic gearbox, if you hold the vehicle on an incline using
the accelerator for too lon
g, the clutchoverheats. Use the brake pedal and/or the parkin
g brake.

77
5
Driving
Only engage reverse gear when the vehicle is stationary with the engine at idle.
As a safety precaution and to facilitate star ting of the engine:


- always select neutral,

- press the clutch pedal.









Manual gearbox
)Push the gear lever fully to the right thenbackwards.


Engaging reverse gear

79
5
Driving
N
appears in the instrument panel.
N
flashes in the instrument panel screen if the gear lever is not in position Nwhen starting.


You must keep your foot on the brakepedal while star ting the engine.
The vehicle then moves off on itsown (refer to the paragraph "Creepfunction").
)
Select automated mode (position A
), A
manual mode (position M ) or reverse (position R
) R
AUTO
and 1
, 1
or R
appear in the
instrument panel.
) Release the parking brake.)
Progressively take your foot off the brake
pedal.

Moving off
)Select position N.
)Press the brake pedal fully.)Star t the engine.
Do not press the brake and clutch pedals simultaneously. This can cause rapid clutch wear.


The creep function may be temporarilyunavailable if the clutch temperature istoo high or the slope too steep.



Do not leave children unsuper visedinside the vehicle when the engine is running.
)
Accelerate away.


Creep function

This function allows the vehicle to be
manoeuvred more easily at low speeds (when
parking, in traffic jams...).
With the gear lever in position A, Mor R, the
vehicle moves as soon as you take your foot off the brake pedal, at low speed andwith the engine at idle.

87
5
Driving





Cruise control
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.

The cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph (40 km/h), as well as the engagement of:


-
fourth gear on a manual gearbox,

- second gear on a or automatic or electronic gearbox, in sequential mode,

- position A
on an electronic gearbox or position D
on an automatic gearbox.
Th
e cruise control is switched off
manually for by pressing the brake or clutch pedal or
on triggering of the ESP system for safety reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal.
Switching off the ignition cancels any programmed speed value. The controls o
f this system are grouped
together on stalk A.
1.Cruise control mode selection thumb wheel.
2. Value decrease button.3.
Value increase button.4.
Cruise control off/resume button.

Steering mounted controls
The cruise control cannot, in any circumstances, replace the need to respect speed limits,nor can it replace the need for vigilance and responsibility on the par t of the driver.

The programmed information is grouped
together in the instrument panel screen.
5. Cruise control off/resume indication.
6. Cruise control mode selection indication. 7. Programmed speed value.
Displays in the instrument panel