2012 MITSUBISHI iMiEV light

2-22 Seat and restraint systems
2
The seat belt pre-tensioner system includes the following com-
ponents:
The airbag control unit monitors the readiness of the electronic
parts of the system whenever the electric motor switch is in the
“ON” or “START” position. These include all of the items
listed above and all related wiring.
The pre-tensioner seat belt system will operate only when the
electric motor switch is in the “ON” or “START” position.When the seat belt pre-tensioners activate, some smoke is
released and a loud noise will be heard. The smoke is not harm-
ful, but care should be taken not to intentionally inhale it, as it
may cause some temporary irritation to people with respiratory
problems.
The pre-tensioners activate in the event of a moderate-to-
severe front or side impact, even if the seat belt is not being
worn. The seat belt pre-tensioners may not activate in certain
frontal collisions, even though the vehicle may appear to be
severely damaged. Such non-activation does not mean some-
thing is wrong with the seat belt pre-tensioner system, but
rather that the collision forces were not severe enough or not of
the type to activate the system.
SRS warning light
N00408700124
This warning light tells you if there is a problem involving the
SRS airbags and/or the pre-tensioner seat belts. Refer to “SRS
warning light” on page 2-44.
1- SRS warning light
2- Front impact sensors
3- Seat belt pre-tensioners
4- Airbag control unit
WA R N I N G
!
The seat belt pre-tensioner system is designed to
work only once. After the seat belt pre-tensioners
have been activated, they will not work again. They
must promptly be replaced and the entire seat belt
pre-tensioner system inspected by a certified i-MiEV
dealer.
BK0140800US.book 22 ページ ２０１１年９月２９日　木曜日　午後３時２８分

2-34 Seat and restraint systems
2
Children who have outgrown child restraint sys-
tems
N00407600591
Children who have outgrown a child restraint system should be
seated in the rear seat and wear the seat belt. If the shoulder
belt crosses their face or neck, and/or the lap belt crosses their
stomach, a commercially available booster seat (including a
booster cushion) must be used, to raise the child so that the
shoulder belt crosses their shoulder and the lap belt remains
positioned low across their hips. The booster seat (including a
booster cushion) should fit the vehicle seat and have a label
certifying compliance with Federal Motor Vehicle Safety Stan-
dards or Motor Vehicle Restraint Systems and Booster Cush-
ions Safety Regulations.
Maintenance and inspection of seat belts
N00407000351
The seat belt webbing may be cleaned with mild soap or deter-
gent solution. Do not use an organic solvent. Allow the belts to
dry in the shade. Do not allow them to retract until completely
dry. Do not attempt to bleach or re-dye the belts. The color may
rub off and the webbing strength may be affected.
Regularly check your seat belt buckles and their release mech-
anisms for positive engagement and release of the latch plate.
Check the retractors for automatic locking when in the Auto-
matic Locking Retractor function.
The entire seat belt assembly should be replaced if the webbing
shows any obvious cuts, tears, increase in thickness in any sec-
tion of the webbing from broken fibers, or severe fading from
sunlight. All of these conditions indicate a weakening of the
belt, which may adversely affect seat belt performance in an
accident.
WA R N I N G
!
Any child who is too small to properly wear a seat
belt must be properly restrained in an appropriate
child restraint system, to reduce their risk of serious
injury or death in an accident.
A child should never be left unattended in, or unsu-
pervised, around your vehicle. When you leave the
vehicle always take the child out as well.
Children can die from heat stroke if left or trapped
inside the vehicle, especially on hot days.
Keep your vehicle locked when not in use. Keep
your vehicle keys away from children.
WA R N I N G
!
Do not attempt to repair or replace any part of the
seat belt assemblies. This work should be done by a
certified i-MiEV dealer. Failure to have a certified i-
MiEV dealer perform the work could reduce the
effectiveness of the belts and could result in a serious
injury or death in an accident.
BK0140800US.book 34 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Seat and restraint systems
2-39
2
How the Supplemental Restraint System works
N00407800489
The SRS includes the following components:
The airbag control unit monitors the readiness of the electronic
parts of the system whenever the electric motor switch is in the
“ON” or “START” position. These include all of the items
listed above and all related wiring.
The airbags will operate only when the electric motor switch is
in the “ON” or “START” position. 1- Driver’s airbag
2- SRS warning light
3- Passenger’s airbag off indicator
4- Front impact sensors
5- Passenger’s front airbag
6- Driver’s seat position sensor
7- Passenger’s seat occupant classification sensor system
8- Airbag control unit
9- Side airbag modules
10- Curtain airbag modules
11- Side impact sensors
BK0140800US.book 39 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Seat and restraint systems
2-41
2
Driver’s seat position sensor
N00417900210
The driver’s seat position sensor is attached to the seat rail and
provides the airbag control unit with information on the seat’s
fore-aft position. The airbag control unit controls deployment
of the driver’s front airbag in accordance with the information
it receives from this sensor.
If there is a problem involving the driver’s seat position sensor,
the SRS warning light in the instrument panel will come on.
Refer to “SRS warning light” on page 2-44.
Passenger’s seat occupant classification sensor
system
N00418000348
The passenger’s seat occupant classification sensor system is
attached to the front passenger seat cushion and provides the
airbag control unit with information regarding the occupant on
the front passenger seat. The airbag control unit controls
deployment of the passenger’s front airbag in accordance with
the information it receives from this system.
The passenger’s front airbag will not deploy in an impact when
the system senses no occupant on the front passenger’s seat or
a child in a child restraint system. In this case, the passenger’s
airbag off indicator will come on.
Refer to “Passenger’s airbag off indicator” on page 2-43.
If there is a problem involving the passenger’s seat occupant
classification sensor system, the SRS warning light in the
instrument panel will come on. Refer to “SRS warning light”
page 2-44.
WA R N I N G
!
If the SRS warning light comes on, have the vehicle
inspected by a certified i-MiEV dealer as soon as
possible.
Please observe the following instructions to ensure
that the driver’s seat position sensor can operate
correctly.
• Adjust the seat to the correct position, and sit well
back against the seatback.
Refer to “Front seats” on page 2-3.
• Do not recline the seatback more than necessary
when driving.
• Do not place metallic objects or luggage under the
front seat.

If the vehicle is involved in a severe impact, have the
SRS sensor inspected by a certified i-MiEV dealer as
soon as possible.
WA R N I N G
!
If any of the following conditions occur, you should
immediately have your vehicle inspected by a certi-
fied i-MiEV dealer as soon as possible:
• The SRS warning light does not initially come on
when the electric motor switch is turned to the
“ON” or “START” position.
• The SRS warning light does not go out after sev-
eral seconds.
• The SRS warning light comes on while you are
driving.
BK0140800US.book 41 ページ ２０１１年９月２９日　木曜日　午後３時２８分

2-44 Seat and restraint systems
2
SRS warning light
N00408300566
There is a Supplemental Restraint System (SRS) warning light
on the instrument panel. The system checks itself each time the
electric motor switch is turned on. When the electric motor
switch is in the “ON” or “START” position, the SRS warning
light should come on for several seconds and then go out. This
means the system is working properly. If there is a problem
involving one or more of the SRS components, the warning
light will come on and stay on. The SRS warning light is
shared by the Supplemental Restraint System (SRS) and the
seat belt pre-tensioner system.
WA R N I N G
!
If any of the following conditions occur, the SRS
and/or seat belt pre-tensioners are not working
properly and you should immediately have it
inspected by a certified i-MiEV dealer:
• The SRS warning light does not come on when the
electric motor key is turned to the “ON” or
“START” position.
• The SRS warning light does not go out after sev-
eral seconds.
• The SRS warning light comes on while driving.
BK0140800US.book 44 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3
Features and controls
Break-in recommendations . . . . . . . . . . . . . . . . . .3- 2
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 2
Electronic immobilizer
(Anti-theft starting system). . . . . . . . . . . . . . . . .3- 3
Keyless entry system . . . . . . . . . . . . . . . . . . . . . . .3- 7
Door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 12
Power door locks . . . . . . . . . . . . . . . . . . . . . . . . . .3- 14
Child safety locks for rear door . . . . . . . . . . . . . . .3- 15
Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 16
Theft-alarm system . . . . . . . . . . . . . . . . . . . . . . . .3- 18
Power window control . . . . . . . . . . . . . . . . . . . . . .3- 22
Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 25
Inside rearview mirror . . . . . . . . . . . . . . . . . . . . . .3- 26
Outside rearview mirrors . . . . . . . . . . . . . . . . . . . .3- 28
Electric motor switch . . . . . . . . . . . . . . . . . . . . . . .3- 30
Steering wheel lock . . . . . . . . . . . . . . . . . . . . . . . .3- 32
Starting the electric motor unit. . . . . . . . . . . . . . . .3- 33
Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 33
Acoustic vehicle alerting system (AVAS) . . . . . . .3- 38
Service brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- 39
Brake assist system . . . . . . . . . . . . . . . . . . . . . . . .3- 40
Anti-lock braking system . . . . . . . . . . . . . . . . . . . .3- 41
Electric power steering system (EPS) . . . . . . . . . .3- 44Active stability control (ASC). . . . . . . . . . . . . . . . 3- 46
Tire pressure monitoring system . . . . . . . . . . . . . . 3- 49
Rear-view camera (if so equipped) . . . . . . . . . . . . 3- 55
Instrument cluster . . . . . . . . . . . . . . . . . . . . . . . . . 3- 58
Indicator and warning light package . . . . . . . . . . . 3- 71
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 72
Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 73
Combination headlights and dimmer switch . . . . . 3- 76
Turn signal lever . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 82
Hazard warning flasher switch . . . . . . . . . . . . . . . 3- 83
Front fog light switch (if so equipped) . . . . . . . . . 3- 83
Wiper and washer switch . . . . . . . . . . . . . . . . . . . 3- 84
Electric rear window defogger switch. . . . . . . . . . 3- 89
Horn switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 90
Link System (if so equipped) . . . . . . . . . . . . . . . . 3- 90
Bluetooth
® 2.0 interface (if so equipped) . . . . . . . 3- 91
USB input terminal (if so equipped) . . . . . . . . . . . 3- 117
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 122
12 V power outlet . . . . . . . . . . . . . . . . . . . . . . . . . 3- 123
Interior lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 124
Storage spaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 128
Cup holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 130
Assist grip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- 131
BK0140800US.book 1 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-3
3
NOTE
The key number (A) is stamped on the key number plate
as shown in the illustration.
Make a record of the key number and store the key and
key number plate in separate places, so that you can order
a key from a certified i-MiEV dealer if the original keys
are lost.

The key is a precision electronic device with a built-in sig-
nal transmitter. Please observe the following in order to
prevent damage.
• Do not leave where it may be exposed to heat caused by
direct sunlight, such as on top of the dashboard.
• Do not take the remote control transmitter apart.
• Do not excessively bend the key or subject it to strong
impacts.
• Keep the remote control transmitter dry.
• Keep away from magnetic objects such as key holders.
• Keep away from devices that produce magnetism, such
as audio systems, computers and televisions.
• Do not clean with ultrasonic cleaners.
• Do not leave the key where it may be exposed to high
temperature or high humidity.

As your vehicle is equipped with an electronic immobi-
lizer, the electric motor unit is designed so that it will not
start if the ID code registered in the immobilizer computer
and the key’s ID code do not match. Refer to the section
entitled “Electronic immobilizer” for details and key
usage.
Electronic immobilizer (Anti-theft starting
system)
N00509100777
The electronic immobilizer is designed to significantly reduce
the possibility of vehicle theft. The purpose of the system is to
immobilize the vehicle if an invalid start is attempted. A valid
start attempt can only be achieved (subject to certain condi-
tions), using a key “registered” to the immobilizer system.
All of the keys provided with your new vehicle have been pro-
grammed to the vehicle’s electronics.
BK0140800US.book 3 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-7
3
General information
N00562300084
Your electronic immobilizer operates on a radio frequency sub-
ject to Federal Communications Commission (FCC) Rules
(For vehicles sold in U.S.A.) and Industry Canada Rules (For
vehicles sold in Canada). This device complies with Part 15 of
the FCC Rules and RSS-Gen of the Industry Canada Rules.
Operation is subject to the following two conditions.

This device may not cause harmful interference.

This device must accept any interference received, includ-
ing interference that may cause undesired operation.
This digital apparatus does not exceed the Class A limits for
radio noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian Department of
Communications.
Keyless entry system
N00509000907
Press the remote control transmitter buttons to lock or unlock
the doors and to open the liftgate.
It can also help you signal for attention by setting off the panic
alarm.
CAUTION
!
Changes or modifications not expressly approved by
the manufacturer for compliance could void the
user’s authority to operate the equipment.
1-
LOCK ( ) button
2-
UNLOCK ( ) button
3- PANIC button
4- Indicator light
BK0140800US.book 7 ページ ２０１１年９月２９日　木曜日　午後３時２８分